Artillian 1UTVTBPR Operating instructions

1 of 8
INSTALLATION & OWNER’S MANUAL
Rev. B, 11/04/2021 p/n: IM-1UTVTBPR
ARTILLIAN UTV BED MOUNTED TOOL BAR FOR
POLARIS RANGER 1000
P/N: 1UTVTBPR
Fits UTV Models: POLARIS RANGER 1000, XP 1000 &
GRAVELY ATLAS JSV 3400SD
The contents of this envelope are the property of the owner. Leave with the owner when installation is complete.
Approximate Installation Time
Experienced Dealer Technician – 30 Minutes
Average Dealer Technician – 45 Minutes
Do-It-Yourself – 60 Minutes
Approximate Product Specifications
Mounting Bar Width: 42 inches
Weight: 37 lbs. (not including accessories)
Capacity: 100 lbs./tool bar (including
accessories)
The Artillian UTV Tool Rack is an innovative system for attaching
accessories to the vehicle’s bed. It allows for carrying ladders, wood, and
any of the Artillian ROPS Mounted Tool Bar Accessories.
The Artillian UTV Bed Mounted Tool Bar for Polaris Ranger 1000 &
Gravely Atlas JSV 3400SD seamlessly integrates the UTV Tool Rack to
the Polaris Ranger 1000 or Gravely Atlas JSV vehicles.
The proprietary Cam Lever Latching feature found on the many optional
accessories allows for installation and removal of a given accessory in
seconds.
CAUTION Do not exceed the rated capacity for the Tool Bar or its accessories.
Doing so may result in damage to the Tool Bar and will void the warranty.
All images shown are for illustration purposes only. Actual product may vary due to product enhancement.

2 of 8
WARNINGS, TIPS, & REQUIRED TOOLS
Artillian products feature an assembly of parts designed for your vehicle which require
adjustment and alignment of components to accommodate vehicle variations and provide
proper installation. For accurate installation, proper operation, and years of satisfaction,
please read and understand the installation and owner’s manual fully prior to installing the
product.
From all of us at Artillian, we thank you for choosing our product.
NOTICE
This product adds additional weight to the base vehicle. All product and accessory
weights are listed in the Installation & Owner’s Manual. Deduct the product (and
accessories) total weight from the vehicle’s rated capacity and never exceed the
vehicle’s rated capacity, including driver and passenger.
WARNING
!
!
This product is intended to increase the functionality of the UTV bed for use in SLOW
SPEED CONDITIONS. The weight and location of this product and its accessories
(when mounted on a UTV bed) will increase the vehicle’s center of gravity. This may
cause the vehicle to become less stable when driving. Additional caution should be
used when driving with this product installed, especially when multiple accessories
and/or tools are added.
TRAVEL SPEEDS MUST BE GREATLY REDUCED TO AVOID ROLLOVER. FAILURE TO
COMPLY COULD RESULT IN INJURY OR DEATH.
This product is not intended for use in trail riding, driving on particularly rough terrain,
on slopes, or at high speeds.
Do not attempt to dump the vehicle bed with accessories installed on either the Tool
Bar or the Tool Rack. Doing so may result in damage to the Tool Bar, the Tool Rack,
the Tool Bar Accessories, or to the vehicle bed or its dumping mechanism.
GENERAL INFORMATION BEFORE YOU START
•To assist with installation, leave all fasteners loose for later adjustment unless otherwise specified.
•Use caution to avoid damaging factory installed threaded inserts. Begin thread engagement by hand
to avoid or correct potential cross-threading.
TOOLS REQUIRED:
•Set of Standard and Metric Sockets (3/8” Drive)
•3/8” Drive Ratchet
•Set of Standard and Metric Open-End Wrenches
•T30 and T40 Torx Bits
•Non-marring Clamps
•Sharpie or other means of marking hole locations
•Drill
•11/32” Drill Bit

3 of 8
1. Park the vehicle on a flat, level surface.
2. Open the tailgate. Use a 10mm socket to remove the
left and then right tail lights. See Fig. 2.
3. Per Fig. 3, disconnect the left and right tail lights from
the vehicle. Set the tail lights with mounting
hardware aside for re-use in Step 12 on the next
page.
4. Close the tailgate and tilt the bed back using the
vehicle’s bed latch. See Fig. 4.
5. Using a T30 Torx bit, remove (4) screws from the
bottom of the left and right sides of the bed. Set
removed hardware aside for re-use. See Fig. 5.
6. Using a T40 Torx bit, remove the screw next to the
latch handle on the left side and right side of the bed.
Set removed hardware aside for re-use. See Fig. 6.
Fig. 5; Remove Underside Screws on the Side Panel
It is the user’s responsibility to ensure that installation of this
product does not affect the functionality of the vehicle ROPS,
tires, or any other safety feature of the vehicle. Failure to do
so may result in injury or death. Due to the many features on
the UTV vehicle, the Bed Mounted Tool Bar or some of its
quick removal accessories may interfere with dump bed
operation, fender flares, or tires. If necessary, the quick-
release Cam Lever Latches on the ROPS Mounted Tool Bar
accessories allow a given accessory to be quickly removed
and relocated to a non-interfering location.
Artillian strives to continuously improve our products. As such, the
actual product may vary from the images shown throughout this
manual.
Fig. 2; Remove Left Tail Light
WARNING
Fig. 3; Disconnect Left Tail Light
Fig. 4; Tilt Bed Back
Fig. 6; Remove Screw Next to Latch Handle
Remove Hardware (4 places per side)
Remove Hardware
Remove Hardware
Disconnect Connector
KIT INSTALLATION
Note: If installing The Artillian UTV Bed Mounted Tool
Bar on the Polaris Ranger 1000, proceed with the
following steps 1-12. If installing on the Gravely Atlas JSV
3400SD, skip to page 5 and start with step 13.

4 of 8
7. Using a T30 Torx bit, remove the (4) screws on the
inside of the left and right side of the bed. When
removing the screws, the side panels will fall off the
bed of the body. Hold the side panels when removing
the screws. See Fig. 7.
8. Put the bed back down. Using (6) of the supplied
5/16” X 6” long bolts and (6) 5/16” washers, use a
1/2” socket to install the left mounting bracket and
backing plate. Repeat this step on the right side of
the bed with right mounting bracket and backing
plate. Torque the 5/16” bolts to 150 (Inch-Pounds)
or 17 (Newton-Meters). See Fig.8.
Note: Make sure that the threaded inserts on the backing
plates are pointed towards the ground as shown in Fig. 8.
9. With assistance, install 42” long tool bar, tube
clamps, and 32” long UTV Tool Rack Vertical Tubes
(supplied in the UTV Bed Mounted Tool Rack) on left
side of bed. Use (4) of the supplied 5/16” X 1” screws
to secure. When placing the tool bar, make sure to
leave a 1” gap between the end of the tool bar and
the ROPS of the vehicle. Repeat on right side. See
Fig. 9.
Note: Make sure that the (2) threaded inserts of the
Vertical tubes are placed on the top/inside of the
assembly.
10. See Installation Manual for Artillian UTV Bed Mounted
Tool Rack (1UTVRK) to complete installation of the
tool rack. Once installation of the tool rack is
complete, finish the below steps to complete this kit
installation.
11. Tilt the bed back. Re-install the bed’s side panels
removed on Steps 5-7. See Fig. 11.
Note: When tilting the bed back, grab the tool rack and
slowly allow the bed to tilt back. Do not let it free fall.
12. Close the bed and open the tailgate. Re-install the
tail lights removed in Steps 2 and 3. Close the
tailgate. See Fig. 12. The kit installation is now
complete.
Note: The 5/16” x 1” long bolts & 5/16” flange nuts may
be discarded if the tool bar has been installed on a Polaris
vehicle.
Fig. 11; Re-install the Bed’s Side Panels
Fig. 7; Remove Left Tail Light
Fig. 8; Install Left Bracket and Backing Plate
Fig. 9; Install Tool Rack’s Vertical Tubes.
Fig. 12; Re-install Tail Lights
KIT INSTALLATION
Remove Hardware (4 Places)
1” gap
Inserts on Underside
Mounting Bracket
Backing Plate
Inside of
tube

5 of 8
Fig. 17; Tool Bar Mounting Hardware
KIT INSTALLATION
1. Position the left side tool bar mounting bracket on top
of the left side bed rail centering it both left to right
and front to rear and clamp in place. See figure 13
below.
2. Using the tool bar mounting bracket as a template,
mark the center of the (6) slots.
3. Remove clamps and set aside the tool bar mounting
bracket. Drill the vehicle’s bed rails where previously
marked.
4. Debur holes and any sharp edges. Paint bare metal
areas to prevent future oxidation.
5. Fasten the left side tool bar mounting bracket using
the (6) supplied 5/16” x 1” bolts, (6) 5/16” washers
and (6) 5/16” flange nuts. See figure 17.
6. With assistance, install 42” long tool bar, tube
clamps, and 32” long UTV Tool Rack Vertical Tubes
(supplied in the UTV Bed Mounted Tool Rack) on left
side of bed. Use (4) of the supplied 5/16” X 1” screws
to secure. When placing the tool bar, make sure to
leave a 1” gap between the end of the tool bar and
the ROPS of the vehicle. Repeat on right side. See
Fig. 9 found on the previous page.
Note: Make sure that the (2) threaded inserts of the
Vertical tubes are placed on the top/inside of the
assembly.
7. Repeat steps 1-6 on the right side of the vehicle.
8. See Installation Manual for Artillian UTV Bed Mounted
Tool Rack (1UTVRK) to complete installation of the
tool rack.
Note: The backing plates and 5/16” x 6” long bolts may
be discarded if tool bar has been installed on a Gravely
vehicle.
5/16” x 1” Bolts 5/16” Washers
5/16” Nuts
Front of Vehicle
Fig. 13; Top View of Bed - Tool Bar Mounting
Bracket Orientation on Gravely Vehicle
Front of Vehicle
Mark the
Center of Slots Tool Bar Mounting
Bracket Bed Rail
FOR INSTALLATION ON GRAVELY ATLAS JSV 3400SD

6 of 8
BACKING PLATE ASS’Y, LEFT
P/N: 8SV-113-00263-L (QTY.: ONE)
BACKING PLATE ASS’Y, RIGHT
P/N: 8SV-113-00263-R (QTY.: ONE)
TUBE CLAMP ASS’Y.
P/N: 8SV-110-00068 (QTY.: ONE)
MOUNTING BRACKET, LEFT
P/N: 8SV-SM-02041-L (QTY.: ONE)
MOUNTING BRACKET, RIGHT
P/N: 8SV-SM-02041-R (QTY.: ONE)
SERVICE PARTS:
1/2” V-GROOVE WEATHERSEAL
P/N: 9SV-PR20-10 (QTY.: 10 FEET)
MOUNTING BAR ASS’Y. (REF.: 42” LG.)
P/N: 8SV-113-00186 (QTY.: ONE)

7 of 8
ROPS MOUNTED TOOLBOX, MEDIUM
P/N: 1RMTBXS
ROPS MOUNTED TOOLBOX, X-LARGE
P/N: 1RMTBXL
ROPS MOUNTED TOOL RACK
P/N: 1RMTRK
ROPS MOUNTED CHAINSAW MOUNT
P/N: 1RMCSM
(chainsaw shown for illustration purposes)
ROPS MOUNTED FUEL CAN HOLDER
P/N: 1RMFCH
(fuel can, etc. shown for illustration purposes)
ROPS MOUNTED TOOL BASKET
P/N: 1RMTBSK
AVAILABLE ACCESSORIES:
MORE ACCESSORIES COMING SOON!
BEVERAGE COOLER HOLDER
P/N: 1RMBCH
(cooler shown for illustration purposes)
ROPS MOUNTED 5-GALLON BUCKET
HOLDER - P/N: 1RM5GBH
(Bucket shown for illustration purposes)
TOOL BAR WALL MOUNT
P/N: 1RMTBWM
BUNGEE NET, 15" SQ., W/6 HOOKS
P/N: 1BN15SQ

8 of 8
Warranty
Artillian, LLC warrants to the original purchaser that this product will be free from defects in material and workmanship
for a period of 90 days from the date possession taken by the original purchaser for use with Artillian hydraulic products
and used as intended and under normal service and conditions for personal use. If not purchased for use with Artillian
hydraulic products (e.g. Grapple, Plow Adapter, etc.), the warranty period is limited to 30 days.
Finishes (coatings, labels, & decals) are not inclusive. Artillian, LLC reserves the right to inspect items claimed to be
defective in material or workmanship. Artillian LLC’s obligation under this warranty is limited to repair or replacement
with a nearest similar part.
This Warranty will not apply to any part or product which in Artillian LLC’s judgment shall have been misused or dam-
aged by accident, abuse, misapplication, fire, negligence, or lack of normal maintenance or care, or which has been
altered or repaired in a way which adversely affects its performance or reliability, or which has been used for a purpose
for which the product is not designed.
Artillian, LLC’s obligations under this warranty, to the extent allowed by law, is in lieu of all warranties, implied or ex-
pressed, including implied warranties of merchantability and fitness for a particular purpose and any liability for incidental
and consequential damages with respect to the sale or use of the product warranted. In any event, liability on behalf of
Artillian LLC is limited to the original purchase price.