Artillian 1RMTBXL Operating instructions

1 of 3
INSTALLATION & OWNER’S MANUAL
Rev. A, 04/30/2020 p/n: IM-1RMTBXL
Approximate Installation Time
Experienced Dealer Technician – 2 Minutes
Average Dealer Technician – 2 Minutes
Do-It-Yourself – 2 Minutes
Approximate Product Specifications
Overall dimensions: 28” L x 13” W x 11” H
Weight: 15.08 lbs. (not including mounting bar)
Capacity: 60 lbs.
The Large Artillian ROPS Mounted Toolbox is a plastic storage container
with an internal tote tray and 10 gauge steel support brackets. The heavy
duty box is rated for 60 pounds. Integrated Cam Lever Latches securely
lock onto the Artillian ROPS Mounted Tool Bar (sold separately) in
seconds without the use of tools.
Bring the box to where the tools are, fill it up, and carry it back to your
tractor. Drop it onto the Tool Bar, cam over the latches, and you are on
your way!
The quick release latches allow for easy removal of the toolbox for storage
or replacement with one of the many other Artillian ROPS Mounted Tool
Bar Accessories.
ARTILLIAN ROPS MOUNTED
TOOLBOX, LARGE, 28”X13”X11”
P/N: 1RMTBXL
For use on the Artillian ROPS Mounted Tool Bar (P/N: 1RMTB) (sold separately)
CAUTION Do not exceed the rated capacity for the Toolbox. Doing so may result
in damage to the Toolbox and/or the Tool Bar and will void the warranty.
The contents of this envelope are the property of the owner. Leave with the owner when installation is complete.

2 of 3
Fig. 1 (attaching a toolbox)
ATTACH TO MOUNTING BAR:
1. Figure 1 shows a toolbox installed onto an Artillian
ROPS Mounted Tool Bar.
2. To install the toolbox, rotate both cam levers UP,
then place onto the Tool Bar. See fig. 2.
Note: if the Cam Lever Latches do not sit flush on the Tool Bar, one
of the clamp plates may not have been fully open. Simply remove the
toolbox, rotate the cam levers up and tilt the toolbox away from you to
ensure the clamp plates are fully open, then reinstall on the Tool Bar.
3. To secure the toolbox to the Tool Bar, rotate both
cam levers DOWN until they cam over. See fig. 3.
NOTE: For additional security, the toolbox can be locked to the Tool
Bar by inserting a padlock through the holes in the mounting bracket
where shown in fig. 3.
4. To remove the toolbox from the Tool Bar, rotate
both cam levers UP, then lift the toolbox.
FEATURES AND OPERATION
1. For optimal functionality, the cam lever latches are
factory assembled with some friction between the cam
lever and the housing. This ensures the cam lever
doesn’t accidentally flip closed while the user attempts to
install it on the bar. If the cam levers loosen up over time,
simply tighten the nut and bolt that secure the lever to
the housing until the desired resistance on the cam lever
has been achieved.
FEATURES AND OPERATION
Fig. 2 (cam lever in the open position)
Fig. 3 (cam lever in the closed position)
rotate both cam levers up
to install the toolbox
padlock holes
rotate both cam levers down
to secure the toolbox

3 of 3
ROPS MOUNTED TOOL RACK
P/N: 1RMTRK
ROPS MOUNTED TOOLBOX, SMALL
P/N: 1RMTBXS
MORE ACCESSORIES COMING SOON!
OTHER ACCESSORIES:
TOOLBOX SUPPORT BRACKET, LARGE
P/N: 8SV-WA-00363 (QTY.: 2)
SERVICE PARTS:
CAM LEVER LATCH
P/N: 8SV-110-00071 (QTY.: ONE)
SAFETY WALK ADHESIVE STRIPS
P/N: 9SV-9PR62-375 (QTY.: 12)
TOOLBOX, DRILLED, 28”X13”X11”
P/N: 8SV-9TB-01A
ROPS MOUNTED CHAINSAW MOUNT
P/N: 1RMCSM
(chainsaw shown for illustration purposes)
ROPS MOUNTED FUEL CAN HOLDER
P/N: 1RMFCH
(Fuel can, wedges, & maul shown for illustration purposes)
ROPS MOUNTED TOOL BASKET
P/N: 1RMTBSK