INSTRUCTIONS FOR:
1.2 METRE WORKBENCH WITH DRAWERS
MODEL No:AP12600.V4
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS1. SAFETY INSTRUCTIONS
4. METHOD OF CONSTRUCTION
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
3. CONTENTS
2. INTRODUCTION
1.0 GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and
general workshop practice regulations are adhered to when
using this bench.
Locate bench in a suitable work area.
Keep the work area clean, uncluttered and ensure there is
adequate lighting.
WARNING! Use bench on level and solid ground, preferably
concrete.
Keep the bench clean and tidy in accordance with good
workshop practice.
Keep children and unauthorised persons away from the work area.
DO NOT use the bench for any purpose other than that for
which it is designed.
DO NOT undertake work on the bench without the workpiece
being adequately secured. Use clamps or a vice (not included)
to secure the workpiece - available from your Sealey dealer.
DO NOT use the bench outdoors .
DO NOT get the bench wet or use in damp or wet locations or
areas where there is condensation.
DO NOT exceed the maximum load for the work surfaces,
worktop and bottom shelf - 100kg each, top shelf - 20kg. Avoid
heavy impacts when placing objects onto the surfaces.
DO NOT clean the bench with any solvents which may damage
the surface or the protective coating on the worktop.
Unpack the product and check the contents against the list below.
Should any items be missing or damaged contact your Sealey dealer.
AP12600.V4 Issue No.1 03/09/10
ITEM PART NO. DESCRIPTION QTY
AAP12600.V3-A LEFT (RIGHT) FRONT POST (900MM) 2
B(L) AP12600.V3-BL LEFT REAR POST (966MM) 1
B(R) AP12600.V3-BR RIGHT REAR POST (966MM) 1
CAP12600.V3-C FEET 4
DAP12600.V3-D SIDE BEAMS (592MM) 4
EAP12600.V3-E BOTTOM BEAMS (1200MM) 2
E1 AP12600.V3-E1 BOTTOM TOP (1197MM) 2
FAP12600.V3-F FRONT & REAR SHELF BEAM (1200MM) 2
GAP12600.V3-G DRAW MOUNTS FRONT/REAR (135MM) 2
H(L) AP12600.V3-HL DRAW MOUNTS, LEFT (605MM) 1
H(R) AP12600.V3-HR DRAW MOUNTS, RIGHT (605MM) 1
I(L) AP12600.V3-IL DRAW MOUNTS, CENTRE LEFT (586MM) 1
I(R) AP12600.V3-IR DRAW MOUNTS, CENTRE RIGHT (586MM) 1
JAP12600.V3-J FRONT PANEL FOR DRAW (530MM) 2
KAP12600.V3-K REAR PANEL FOR DRAW (510MM) 2
L(L) AP12600.V3-LL LEFT SIDE PANEL FOR DRAW (455MM) 2
L(R) AP12600.V3-LR RIGHT SIDE PANEL FOR DRAW (455MM) 2
N(L) AP12600.V3-NL LEFT EXTENSION POST (610MM) 1
N(R) AP12600.V3-NR RIGHT EXTENSION POST (610MM) 1
O(L) AP12600.V3-OL LEFT TOP SHELF BEAMS (230MM) 1
O(R) AP12600.V3-OR RIGHT TOP SHELF BEAMS (230MM) 1
PAP12600.V3-P BOTTOM SHELF (1210 x 605 x 15MM) 1
QAP12600.V3-Q WORKTOP (1210 x 603 x 15MM) 1
RAP12600.V3-R PEGBOARD (1210 x 580 x 4.5MM) 1
SAP12600.V3-S TOP SHELF (1205 x 228 x 6.0MM) 1
TAP12600.V3-T DRAW BOTTOM (512 x 450 x 6MM) 2
UAP12600.V3-U DRAW HANDLE 2
VAP12600.V3-V M4 x 10MM - Draw handle bolts (8pcs), nuts (8pcs), washers (8pcs) 24
WAP12600.V3-W M6 x 15MM - Fixing kit bolts (8pcs), nuts (8pcs), washers (12pcs) 28
XAP12600.V3-XH Toolhook 20
YAP12600.V4-Y M6 x 10MM - Draw bolts (16pcs), nuts (16pcs), washers (16pcs) 48
2.1 Introduction:
Boltless design makes the unit easy to assemble, with minimal
tools being required. Pegboard rear panel with hooks for
convenient tool storage. Two half drawers, with ball bearing
slides, full size shelf below worktop and 230mm shelf above
pegboard.
2.2 Dimensions:
Size (W x D x H [Overall/Worktop]):1215 x 610 x 1500/900mm
Worktop: 1205 x 600mm
Structural members have
flat headed, waisted
rivets attached which
pass through keyholes in
the uprights and are
pushed down to secure
them.
Original Language Version
