artisan 25 Series Installation manual

IDC with
Rechargeable Battery
Series Ø25 IØ35
Applies to Item Numbers :
ENGLISH
1
Features:
•Internal rechargeable lithium battery
•Operates taller shades
•Simple electronic setting of limits and other
adjustments
•Multiple intermediate limits
•Jogging function and tilting for Horizontal
Blinds
•433.92 MHz radio frequency communication
•DC: direct current, low voltage
•Roller Shades, Dual Shades, and Horizontal
Blinds applications
•Smart control with Smart Hub
•Compatible with leading brands of Home
Automation Systems
Artisan Rechargable Motor
PROGRAMMING INSTRUCTIONS

•Setting int ermediate limits
•Erasing an intermediate limit
•Readjusting the lower or
an intermediate limit
•Setting the motor into “sleep mode”
•“Waking up” the motor
•Adding an additional remote or
“cloning” a channel
•Changing to tilt or jog mode
•Deleting a single motor or channel
•Deleting all channels
•Resetting the motor to factory default
Optional functions
Initial programming sequence
Before starting...
It is extremely important to charge battery motors for at least 8 hours on initial charge, prior to
installation.
1Select the desired remote control and channel.
2Pair the motor with the remote control.
3Check the direction of rotation of the motor
and change it if needed.
4Set the upper limit.
The upper limit must always be set rst.
5Set the lower limit.
UP OR
DOWN?
2

Pairing the motor with the remote control
1. Press and hold the programming button on the
head of the motor until the moto r “jogs” .
2. Select the desired channel and press the
up button until the motor “jogs” .Now the motor
is paired with the remote control.
3
PROGRAMMING
BUTTON
UP
BUTTON
STOP
BUTTON
This function must be done before setting the limits and is convenient when the need arises to
change the rotation of the motor. For example, when pressing the up button on the remote
control, the shade goes down, or when pressing the down button, the shade goes up.
Checking the direction of rotation
1. Press and hold the stop button for about 5 s
until the motor “jogs” .
2. Release the stop button, and press the down
button for about 2 s .The motor has now changed
its direction. DOWN
BUTTON
The upper limit must be set rst and cannot be erased ormodied once ithas been set. If you have
made a mistake setting the upper limit, reset the motor to factory default setting and start the
initial programming sequence again.
Setting the upper limit
1. Using the remote, move the shade and stop it
approximately 4" below the desired upper limit
position. Press and hold the programming button
located on the back of the remote until the
motor “jogs” .
2. Move the shade up to the desired upper limit
position and then press and hold the program ming
button until the motor “jogs” again. The upper
limit is now set.
UPPER
LIMIT
PROGRAMMING
BUTTON
~4”
PROGRAMMING
BUTTON

The upper limit cannot be erased or modied once it has been set.
Erasing an intermediate limit
1. Move the shade to the limit you want to erase.
2. Press and hold the programming button
located on the back of the remote for approxima tely
7 s until the motor “jogs” twice. The limit has
been erased.
PROGRAMMING
BUTTON
*Repeat the same steps for any additional intermediate limit.
1. Move the shade approximately 4" from the
desired intermediate limit position and stop it.
Press and hold the programming button located
on the back of the remote until the motor “jogs”
(Openning program) .
2. Move the shade up or down and stop it at the
desired intermediate limit position and then press
and hold the programming button until the motor
“jogs” again (Closing Program) . The intermediate
limit is now set.
Setting intermediate limits (optional)
Up to 4 optional intermediate limits can be programmed between the upper and lower limit. Press
and hold the up or down button for 2 s if you want the motor to reach the upper or lower limit
without any stop at the intermediate limits.
PROGRAMMING
BUTTON
~4”
INTERMEDIATE
LIMIT
PROGRAMMING
BUTTON
Setting the lower limit
1. Using the remote, move theshade and stop it
approximately 4" above the desired lower limit
position. Press and hold the programming button
located on the back of the remote until the
motor “jogs” .
2. Move the shade down to the desired lower limit
position and then press and hold the program ming
button until the motor “jogs” again. The lower
limit is now set.
LOWER
LIMIT
PROGRAMMING
BUTT ON
~4”
PROGRAMMING
BUTTON
4

5
Readjusting the lower or an intermediate limit
1. Move the shade to the limit you want to readjust.
Press and hold the programming button located
on the back of the remote until themotor “jogs” .
2. Move the shade to the new desired position and
press stop. Then press andhold the programming
button located on the back of the remote until the
motor “jogs” . The limit has been readjusted.
“Waking up” the motor
The following function is necessary only when more than one motor is programmed on the same
channel. Repeat the same procedure with all the previously programmed motors each time you want
to add a new battery motor into the same channel or modify an existing one and at the end wake up all
the motors.
Setting motor into “sleep mode”
PROGRAMMING
BUTTON
1. Press and hold the programming button on
the head of the already programmed motor, the
motor will “beep” and then “jog” once, but keep
holding the button down until you hear a long
“beep” . The motor is now in “sleep mode”. You
can now program another motor in the same
channel by repeating the procedure described in
the initial programming sequence.
2. Release the programming button , and press the
up button on the desired channel.
1. Press and hold the programming button on the
head of the motor until the motor “beeps” once.
UP
BUTTON
PROGRAMMING
BUTTON
PROGRAMMING
BUTTON
PROGRAMMING
BUTTON

Adding an additional remote control or
“cloning” a channel
A previously programmed remote control can be used in order to add a new remote control or
operating channel. Also, you can copy one channel to another in the same remote control using
this procedure.
Changing to tilt or jog mode
Tilt or jog mode initiates a short motor movement when pressing the up or down buttons.
The tilt or jog mode is convenient for Venetian Blinds, Wood Blinds and Dual Shades since it
allows the jogging of the slats in a more precise way. When this mode has been programmed,
the up or down button must be pressed for 3 s to make the motor move continually to its upper
or lower limits, otherwise when you press the up and down button the motor will do short
movements.
Repeat the same procedure if you want to erase the tilt or jog mode .
2. Release the stop button and press it again for
about 2 s . The motor will “jog” again.
The tilt or jog mode has been programmed.
1. Press and hold the stop button for about 5 s
until the motor “jogs” .STOP
BUTTON
STOP
BUTTON
1. Using the previously programmed remote,
select the desired channel using the channel
selector button , then press and hold the stop
button for about 5 s until the motor “jogs” .
2. Using the new remote, select the desired
channel using the channel selector button , and
then press the up button until the motor “jogs” .
hades are now paired with the new remote or
channel.
STOP
BUTTON
UP
BUTTON
PREVIOUSLY
PROGRAMMED
REMOTE CONTROL
NEW REMOTE
CONTROL
OR CHANNEL
6

7
2. Press and hold the programming button for
about 2 s until the motor “jogs” .The selected
channel has been deleted. Motors previously
linked to this channel are not linked anymore.
1. Select the desired channel using the
channel selector button,and press and hold the
stop button for about 5 s until the motor “jogs” .
Deleting all channels
2. Press and hold the programming button for
about 7 s . The motor will “jog” , and in a few
seconds the motor will “jog” two more times. All
previous programming on the remote control has
been deleted.
1. Press and hold the stop button for about 5 s
until the motor “jogs” .
Deleting a single motor or channel
This is a convenient feature when there has been a programming mistake and it is required to
delete the programming from a single channel. Also if you want to delete a programmed motor in
a single channel, put all motors previously programmed in this channel into sleep mode, except
the one you want to delete and follow this procedure.
PROGRAMMING
BUTTON
STOP
BUTTON
This is needed when there has been a programming mistake and the remote control needs to be reset.
Make sure that all the motors linked to this remote control are not in “sleep mode”.
Resetting the motor to factory default
PROGRAMMING
BUTTON
STOP
BUTTON
1. Press the programming button located on the
head of the motor 5 consecutive times (every
time you press, the motor will “beep” ) and hold
the button on the fth time until the motor “jogs”
twice. All previous programming on the motor
has been deleted. PROGRAMMING
BUTTON

Troubleshooting guide
Motor does not respond to the program ming
button or motor does not work.
Problem
Motor is fully charged but is sluggish
lifting the shade.
Motor does not jog when pressing the
programming button on the back of the
remote control.
Intermediate limits cannot be set.
(This usually happens when there are 2
limits too close to each other).
The motor stops suddenly while working.
The motor is noisy.
Cannot program a single motor since
multiple motors respond.
• Motor does nothave enough battery. Charge it for at
least 8 hours prior to use.
• Change the battery in your remote control.
• Check the maximum weight capacity of the
motor to make sure themotor used can handle the load.
• The crown is notproperly tted to the tube.
Move the shade slightly up or down (approximately 10 in)
and try again.
Make sure the motor has made at least 2 full turns
from the preceding limit before doing the “Openning
Program” sequence described in the function to set an
intermediate limit.
The motor has exceeded thermal overheat protection.
Wait for the motor to cool down for approximately 15 min.
• The drive and the crown are not well adapted to the tube.
• The shade is not snug between thebrackets.
• Debris, screws orother items are in yourtube.
Note: The noise level of any motorized shade installed in a cassette or
fascia will always be higher. Take into consideration that a cassette is an
enclosed structure that will behave like an echo chamber.
Place all other motors into sleep mode since multiple
motors are paired to the same channel.
Probable cause and solution
IMPORTANT: The values, recommendations and instructions in this manual may vary at any time without previous notice.
They are not contractual and can not be used as claim for defective merchandise, order cancellations or returns.
For additional information contact your representative or Authorized Dealer.
8

Funciones opcionales
•Congurar los límites intermedios
•Borrar un límite intermedio
•Reajustar el límite inferior o un
límite intermedio
•Congurar el motor en “modo sueño”
•“Despertar” el motor
•Adicionar un nuevo control remoto o
“clonar” un canal
•Congurar o borrar la función de giro de lamas
•Borrar un motor de un canal o borrar un canal
•Borrar todos los canales
• Congurar el motor a sus valores de fábrica
Secuencia inicial de programación
Antes de comenzar….
1Seleccione el control remoto y canal deseado.
2Enlace el motor con el control remoto.
3Determine cuál es la dirección de rotación del
motor y cámbiela si fuera necesario.
4Congure el límite superior.
El límite superior siempre debe ser congurado
primero que el inferior.
5Congure el límite inferior y los límites intermedios
opcionales.
Es muy importante cargar los motores durante al menos 8 horas antes de comenzar su
programación por primera vez.
SUBE O
BAJA?
10

11
Enlazar el motor con el control remoto
1. Mantenga presionado el botón de programación
ubicado en la cabeza del motor hasta que el
motor realice un “movimiento” .
2. Seleccione el canal deseado y presione el
botón de subida hasta que el motor realice un
“movimiento” . Verique que el motor comienza a
rotar al presionar el botón de subida obajada .
BOTÓN DE
PROGRAMACIÓN
BOTÓN DE
SUBIDA
Esta función es conveniente cuando la dirección de rotación del motor necesita ser cambiada; es
decir, cuando al presionar el botón de subida , la cortina comienza a bajar o viceversa. Tenga en
cuenta que de ser necesario, usted debe cambiar la rotación del motor antes de congurar los
límites superior e inferior .
Cambiar la dirección de rotación del motor
1. Presione el botón de parada por
aproximadamente 5 s hasta que el motor realice
un “movimiento” .
2. Libere el botón de parada y presione el botón
de bajada por aproximadamente 2 s . Compruebe
que el motor haya cambiado su dirección de
rotación.
El límite superior debe ser el primero en ser congurado y una vez programado no puede ser
borrado o modicado. Si se ha cometido un error durante su conguración, borre el motor y
regréselo a sus valores de fábrica. Luego vuelva a empezar la secuencia de programación.
Congurar el límite superior
1. Usando el control remoto, mueva la cortina
aproximadamente 20 cmpor debajo del límite
superiordeseado y deténgala en esta posición.
Luego presione el botón de programación
ubicado al dorso del control remoto hasta que el
motor realice un “movimiento” .
LÍMITE
SUPERIOR
BOTÓN DE
PROGRAMACIÓN
2. Mueva la cortina hasta el límite superior deseado
y luego presione el botón de programación hasta
que el motor realice un “movimiento” .
El límite superior ha quedado congurado.
BOTÓN DE
PROGRAMACIÓN
~20 cm
BOTÓN DE
PARADA
BOTÓN DE
BAJADA

Se pueden programar hasta 4límites intermedios opcionales entre el límite superior y el inferior .
Mantenga presionado el botón de subida o bajada por 2 s si desea que el motor alcance el límite
superior o inferior sin detenerse en los límites intermedios.
Congurar los límites intermedios (opcional)
LÍMITE
INTERMEDIO
BOTÓN DE
PROGRAMACIÓN
BOTÓN DE
PROGRAMACIÓN
1. Utilizando el control remoto, mueva la cortina
aproximadamente 20 cm con respecto al límite
intermedio deseado y deténgala en esta posición.
Luego presione el botón de programación ubicado
al dorso del control remoto hasta que el motor
realice un “movimiento” (Abrir Programación) .
2. Mueva la cortina y deténgala cuando alcance
el límite intermedio deseado, y luego presione el
botón de programa ción hasta que el motor realice
un “movimiento” (Cerrar Programación) .
El límite intermedio ha quedado congurado.
~20 cm
Borrar un límite intermedio
*Repita los mismos pasos para agregar límites intermedios adicionales.
BOTÓN DE
PROGRAMACIÓN
1. Mueva la cortina hasta el límite que desea
eliminar.
2. Presione el botón de programación ubicado al
dorso del control remoto por aproximadamente 7 s
hasta que el motor realice dos “movimientos”
consecutivos.
Congurar el límite inferior
BOTÓN DE
PROGRAMACIÓN
1. Usando el control remoto, mueva la cortina
aproximadamente 20 cm por encima del límite
inferior deseado y deténgala en esta posición.
Luego presione el botón de programación ubicado
al dorso del control remoto hasta que el motor
realice un “movimiento” .
2. Mueva la cortina hasta el límite inferior
deseado yluego presione el botón de programa ción
hasta queel motor realice un “movimiento” .
El límite inferior ha quedado congurado. LÍMITE
INFERIOR
BOTÓN DE
PROGRAMACIÓN
~20 cm
12

13
Reajustar el límite inferior o un límite intermedio
BOTÓN DE
PROGRAMACIÓN
BOTÓN DE
PROGRAMACIÓN
1. Mueva la cortina hasta el límite que desea
reajustar. Presione el botón de programación
ubicado al dorso del control remoto hasta que el
motor realice un “movimiento” .
2. Mueva la cortina y deténgala en la nueva
posición deseada. Luego presione el botón de
programación ubicado al dorso del control
remoto hasta que el motor realice un “movimien to”.
El nuevo límite ha sido programado.
Esta función es necesaria cuando se desea programar más de un motor de batería en un mismo
canal. Repita el siguiente procedimiento con todos los motores programados previamente cada vez
que desee adicionar un nuevo motor de batería en el mismo canal. Al terminar la programación
realice el procedimiento descrito en la función “despertar el motor” .
Congurar el motor en “modo sueño”
2. Libere el botón de programación y presione el
botón de subidaen el canal deseado.
1. Mantenga presionado el botón de programación
ubicado en la cabeza del motor hasta que el motor
emita un sonido.
BOTÓN DE
PROGRAMACIÓN
1. Mantenga presionado el botón de programación
ubicado en la cabeza del motor que ha sido
previamente programado en un canal del
control remoto. El motor emitirá un sonido y
luego realizará un “movimiento” pero mantenga
presio nado el botón hasta que el motor emita un
sonido continuo.
El motor se encuentra en “modo sueño” . Ahora
puede congurar otro motor en el mismo canal.
BOTÓN DE
PROGRAMACIÓN
“Despertar” el motor
BOTÓN DE
SUBIDA

Adicionar un nuevo
control remoto o“clonar” un canal
Un control remoto previamente programado puede utilizarse para añadir un nuevo control remoto
como una réplica del primero. Adicionalmente, también es posible copiar un canal a otro en un
mismo control remoto o en un control remoto adicional utilizando el mismo procedimiento
descrito a continuación.
1. Utilizando un control remoto previamente
programado, seleccione el canal que desea copiar
y mantenga presionado el botón de parada por
aproximadamente 5 s hasta que el motor realice
un “movimiento” .
BOTÓN DE
PARADA
CONTROL REMOTO
PREVIAMENTE
PROGRAMADO
2. Utilizando el nuevo control remoto, seleccione
el canal donde desea realizar la copia y mantenga
presionado el botón de subida hasta que el motor
realice un “movimiento” . El motor ahora está
congurado en el nuevo control remoto o canal.
Congurar o borrar la función de giro de lamas
Cuando la función de giro de lamas está congurada el motor realiza pequeños movimientos al
presionar los botones desubidao bajada. Esta f unción es conve niente para las cortinas
venecia nas, p ersianas demadera , o cortinas enrollables duales ya que permi te el giro de las
lamas con mayor precisión. Cuando esta función está programada, los botones de bajada o
subida deben ser presionados por 3 s si desea que el motor alcance sus límites superior o
inferior (en vez de realizar cortos movimientos, rota de forma continua hasta alcanzar sus
límites). Para borrar la función de giro de lamas repita el mismo procedimiento que se describe
para congurarla.
BOTÓN DE
SUBIDA
NUEVO
CONTROL REMOTO
O CANAL
BOTÓN DE
PARADA
2. Libere el botón de parada y vuelva a presionarlo
por aproximadamente 2 s hasta que el motor
vuelva a realizar un “movimiento” .
La función de giro de lamas ha sido congurada.
1. Mantenga presionado el botón de parada por
aproximadamente 5 s hasta que el motor realice
un “movimiento” .
BOTÓN DE
PARADA
14

15
Borrar un motor de un canal o
borrar un canal
Esta función es conveniente cuando se ha cometido un error durante la programación y se
requiere borrar un solo canal. También se aplica si se desea borrar un motor de un canal
especíco. Programe todos los motores en “modo sueño” excepto el que desea borrar y
siga el procedimiento.
2. Libere el botón de parada ypresione el botón
de programación por aproximadamente 2 s hasta
que el motor realice un “movimiento” .
El canal ha sido borrado. Todos los motores
asociados a este canal han sido borrados.
1. Selecione el canal deseado, luego mantenga
presionado el botón de parada por
aproximadamente 5 s hasta que el motor realice
un “movimiento” .
Esta función es conveniente cuando se desea que el control regrese a sus valores de fábrica.
Asegúrese de que todos los motores programados en el control no se encuentren en “modo sueño”.
Borrar todos los canales
BOTÓN DE
PROGRAMACIÓN
BOTÓN DE
PARADA
BOTÓN DE
PARADA
Congurar el motor a sus valores de fábrica
1. Mantenga presionado el botón de parada por
aproximadamente 5 s hasta que el motor realice
un “movimiento” .
2. Libere el botón de parada y presione el botón de
programación por aproximadamente 7 s. El motor
realizará un “movimiento” y un par de segundos
después realizará 2“movimientos” más. Toda la
programación del control ha sido borrada.
BOTÓN DE
PROGRAMACIÓN
1. Presione el botón de programaciónubicado en
la cabeza del motor 5veces consecutivas
(el motor debe emitir un sonido cada vez que
oprima el botón)y en la quinta vez, manténgalo
presionado hasta que el motor realice 2
“movimientos” consecutivos.
Toda la programación previa ha sido borrada.
BOTÓN DE
PROGRAMACIÓN

16
Guía de solución de problemas
Problema
El motor no responde al botón de
programación o simplemente
no está trabajando.
El motor está completamente cargado
pero levanta la cortina lentamente o se
detiene antes de completar el ciclo.
El motor no realiza ningún movimiento
cuando sepresiona el botón de programación
ubicado al dorso del control remoto para
congurar los límites.
Los límites intermedios no pueden ser
congurados.
(Usualmente ocurre cuando se desean
congurar 2 límites que se encuentran
muy próximos entre sí).
El motor se ha detenido repentinamente
durante su funcionamiento.
El motor hace mucho más ruido que el
habitual.
Un solo motor no puede ser programado
ya que varios motores responden al
entrar al modo de programación.
•Revise que el motor tenga suciente batería. Cargue el
motor durante 8 horas antes de programarlo.
•Cambie la batería del control remoto.
•Verique que no esté superando la capacidad de
carga máxima del motor. Utilice un modelo de mayor
torque si fuera necesario.
•La corona no está ajustada al tubo.
Mueva la cortina aproximadamente 20 cm hacia arriba o
hacia abajo e inténtelo nuevamente.
Mueva el motor de modo que realice al menos 2
rotaciones completas (hacia arriba o hacia abajo) antes
de realizar la función de “Abrir Programación” si desea
congurar un límite muy cerca de otro previamente
congurado. Luego siga la secuencia para congurar el
límite deseado.
El motor ha estado operando por más de 4 min y ha
activado su mecanismo de protección contra
sobrecalentamiento. Espere a que se enfríe el motor
(15 min aproximadamente).
Asegúrese de realizar una correcta instalación para
evitar las posibles causas descritas a continuación:
• La rueda motriz y la corona no están bien adaptadas al tubo.
•El sistema no está bien connado entre los brackets.
•Existen restos de limalla de aluminio dentro del tubo.
Nota: El nivel de ruido de una cortina motorizada instalada en un
casete o fascia siempre será mayor. Tenga en cuenta que un casete es
una estructura cerrada que se comportará como una cámara de eco.
Si usted desea programar más de un motor en un mismo
canal debe poner el resto de los motores previamente
añadidos a este canal en “modo sueño”.
Causa probable y solución
IMPORTANTE: Los valores, recomendaciones e instrucciones en este manual pueden variar en cualquier momento sin
previo aviso. Los mismos no son contrac tuales yno pueden ser utilizad os como reclamo para mercancía defectuosa,
cancelaciones de pedidos o devoluciones.
Para información adicional contacte a un representante de o un distribuidor autorizado.
This manual suits for next models
1
Table of contents
Languages:
Other artisan Robotics manuals