ASA Electronics K-9 User manual

Page 1of 10
P/N 8007132
REV. B BJ
ASA Electronics TV/VCP Floor Console
Model K-9 With out Harness and Antenna
12 Volt DC powered remote controlled 9” television AVT-975
12 Volt DC powered remote controlled VHS Video Cassette Player AVP-7000
Installation Instructions
Audiovox Specialized Applications, LLC
23319 Cooper Drive
Elkhart IN 46514
1 [phone]
www.audiovox.com

P/N 8007132
Page 2of 10
Rev. B
This manual contains specific instructions on how to install this automotive TV/VCP
floor console. Please read this manual thoroughly before installing the console into
the vehicle.
**WARNING**
In order to maintain a safe mounting system, this console MUST be secured to
the floor of the vehicle according to the instructions contained in this manual.
Failure to do so may result in the console breaking loose in the event of an
accident.
It is unlawful in most jurisdictions for a person to drive a motor vehicle which
is equipped with a television viewer or screen that is located in the motor
vehicle at any point forward of the back of the driver’s seat, or that is visible,
directly or indirectly, to the driver while operating the vehicle. This product
should only be installed to the rear of the driver’s seat where it will not be
visible, directly or indirectly, to the operator of the motor vehicle.
Required tools for installation:
Electric drill
¼” steel drill bit
1/8” steel drill bit
Phillips screwdriver
Socket wrench set with deep-well, 7/16” socket
Box end wrench, size 7/16”
Soldering Iron
Two people are required for installation.
0892105 Bracket Kit 1
8007101 Bracket, Mounting 4
8007105 Screw, Hex #8x3/4 self drilling 20
8007106 Washer, 3/16” 20
8007110 Strap, Open, Nylon 1
8007111 Strap, Loop, Nylon 1
8007125 Bolt, ¼”x1 ½”, Hex 4
8007126 Washer, Fender 5/16” 4
8007128 Nut, Nylon Insert ¼” 4
8007132 Installation Manual 1

P/N 8007132
Page 3of 10
Rev. B
There are six (6) steps to install the K-9 TV/VCP floor console:
Step # 1 Remove face of the console
Step # 2 Install brackets and the straps
Step # 3 Install console to the floor of the vehicle
Step # 4 Install VCP
Step # 5 Install TV
Step # 6 Replace console face
STEP #1 REMOVE THE FACE OF THE CONSOLE
⇒Remove 4 Phillips screws securing face of console to body of console.
⇒Set screws and face aside. Take care that screws do not get lost.
1) Disassemble shroud.

P/N 8007132
Page 4of 10
Rev. B
Step #2 Install brackets and straps
1) Mount brackets using four screws. Do not use center hole.
2) Use soldering iron, if necessary, to melt holes in open strap, as shown.
3) Use soldering iron, if necessary, to melt holes in closed strap, as shown.

P/N 8007132
Page 5of 10
Rev. B
3) Pre-drill 1/8” pilot holes on bottom TV shelf for strap.

P/N 8007132
Page 6of 10
Rev. B
1) Attach both straps and customer-supplied harness, securing harness as needed.

P/N 8007132
Page 7of 10
Rev. B
Step #3 INSTALL CONSOLE TO FLOOR OF VEHICLE
⇒BEFORE DRILLING ANY HOLES VERIFY THAT DRILL BIT WILL NOT ENTER
INTO FRAME RAIL(S) OF VEHICLE, ELECTRICAL WIRES, FUEL LINES,
BRAKE LINES, HOSES, EXHAUST SYSTEMS OR ANY OTHER ITEMS THAT
WILL IMPAIR OPERATION OF VEHICLE. THE BOLTS OF THE FLOOR
CONSOLE MUST SECURE TO FLOOR PANEL OF VEHICLE. CLIMB UNDER
VEHICLE AND LOOK TO VERIFY THAT HOLES WILL BE IN PROPER
LOCATIONS.
⇒Set console on floor of vehicle and mark where holes are to be drilled. Drill
small 1/8” pilot holes to verify that drill holes are in proper locations.
⇒After verifying that 1/8” pilot holes are in proper locations, use ¼” drill bit to
enlarge 1/8” pilot holes.
⇒Set console on floor over holes.
⇒Place bolts through feet of console and into holes previously drilled.
⇒Place one large fender washer over each of bolts and attach nuts.
⇒Tighten nuts down securely. Have second person inside vehicle hold bolts
securely with box-end wrench while person underneath vehicle tightens down
nuts.

P/N 8007132
Page 8of 10
Rev. B
STEP #4 INSTALL VCP INTO CONSOLE
⇒Remove VCP from box.
⇒Connect white RCA connector (customer supplied) from console wiring harness
to white audio output jack of VCP.
⇒Connect yellow RCA connector (customer supplied) from console wiring harness
to yellow audio output jack of VCP.
⇒Connect DC power connector (customer supplied) from console to DC power
jack of VCP.
⇒Slide VCP into slot in front of console.

P/N 8007132
Page 9of 10
Rev. B
STEP #5 INSTALL TV INTO CONSOLE
⇒Connect yellow RCA connector (customer supplied) to yellow RCA input jack on
rear of television. This is the video connection.
⇒Connect white RCA connector (customer supplied) to white RCA input jack on
rear of television. This is the audio connection.
⇒Connect DC power connector (customer supplied) to rear of television.
⇒Connect coaxial cable antenna “F” connector (customer supplied)to rear of
television “ANT” input.
⇒Place television on shelf of console.
⇒Secure television down with two straps. Make absolutely certain that straps are
tight.

P/N 8007132
Page 10 of 10
Rev. B
STEP #6 REPLACE THE FACE OF THE CONSOLE
⇒Place face of console over body of console. Gently tap into place.
⇒Install four Phillips screws that hold the face to the body.