Asante IntraCore 3524 Series User manual

IntraCore™3524 Series
Gigabit Ethernet Switches
User’s Manual

2
Quick Start Guide
Follow these steps to install your IntraCore switch:
1. Open the box and check the contents. See Chapter 1.1 Package Contents for a complete list of the
items included with your IntraCore switch.
2. Install the switch in an equipment or wall rack, or prepare it for desktop placement.
3. Connect the power cord to the unit and to an appropriate power source.
4. Connect network devices to the switch.
5. Refer to Chapters 3-5 to configure the IntraCore 3524 for configuration and management
capabilities.
For more information on installing the IntraCore 3524, please refer to Chapter 2 Installation and Setup.

3
IntraCore 3524 Series
Gigabit Ethernet Switches
User’s Manual
Asanté Technologies, Inc.
821 Fox Lane
San Jose, CA 95131
USA
SALES
800-662-9686 Home/Office Solutions
800-303-9121 Enterprise Solutions
408-435-8388
TECHNICAL SUPPORT
801-566-8991: Worldwide
801-303-3787: FAX
www.asante.com
[e-mail]
Copyright © 2001 Asanté Technologies, Inc. All rights reserved. No part of this document, or any associated artwork,
product design, or design concept may be copied or reproduced in whole or in part by any means without the express
written consent of Asanté Technologies, Inc. Asanté is a registered trademark and the Asanté logo, IntraCore, IntraCare
and AsantéCare are trademarks of Asanté Technologies, Inc. All other brand names or product names are trademarks or
registered trademarks of their respective holders. All features and specifications are subject to change without prior
notice.
Rev. C

4
Table of Contents
Quick Start Guide 2
Chapter 1. Introduction 6
1.1 Package Contents 6
1.2 LEDs 6
1.3 Front Panel Description 7
1.4 Management and Configuration 8
Chapter 2. Hardware Installation and Setup 9
2.1 Installation Overview 9
2.2 Installation into an Equipment Rack 10
2.3 GBIC Interfaces 11
2.4 Installing Optional Hardware Modules 12
2.5 Connecting Power 12
2.6 Connecting to the Network 13
2.7 Setup 14
2.8 Changing the Password 15
2.9 IP Assignment 16
2.10 SNMP Management 16
2.11 Using the Stacking Feature 17
Chapter 3. Configuration 19
3.1 General Information 20
3.2 Configuration Menu 20
3.3 System Administration Configuration 21
3.4 System IP Configuration 22
3.5 Bootstrap Configuration 22
3.6 SNMP Configuration 23
3.7 Port Configuration 25
3.8 Advanced Port Configuration 28
3.9 Unicast Forwarding Database Configuration 30
3.10 Security Management 32
3.11 VLAN Management 32
3.12 IP Multicast Traffic Management 32
3.13 Port Mirroring Configuration 32
3.14 File Up/Downloading Configuration 33
3.15 System Reset Configuration 36
3.16 System Log 37
3.17 User Interface Configuration 38
3.18 System Utility 39
3.19 Viewing Statistics 40
Chapter 4. Advanced Management 41
4.1 Spanning Tree Protocol 41
4.2 SNMP and RMON Management 43
4.3 Security Management 43
4.4 VLAN Management 47
4.5 IP Multicast Traffic Management 52
Chapter 5. Web-Based Management 55
5.1 Front Panel Button 56
5.2 Genl Info (General Information) Button 56
5.3 Statistics Button 57
5.4 Port Config (Port Configuration) Button 58
5.5 Span Tree (Spanning Tree) Button 59
5.6 SNMP Button 60
5.7 Addr (Address) Table Button 60
5.8 VLAN Button 61
5.9 Security Button 65

5
5.10 Duplicate IP Button 66
Chapter 6. SNMP Management 67
6.1 SNMP Management Operations 67
6.2 The SNMP Protocol 67
6.3 Community Name and Security 68
6.4 The MIB Tree 68
Chapter 7. Switching Concepts 70
7.1 VLANs 70
7.2 Spanning Tree Protocol 71
7.3 Full Duplex, Flow Control and Auto-negotiation 72
Appendix A. Troubleshooting 74
Appendix B. Features and Specifications 75
B.1 Features 75
B.2 Specifications 75
Appendix C. FCC Compliance and Warranty Statements 77
Appendix D. Console Port Pin Outs 79
Appendix E. Online Warranty Registration 80
Appendix F. BootP Configuration 81

6
Chapter 1. Introduction
Thank you for purchasing the Asanté IntraCore 3524 Series Gigabit switch. The IntraCore 3524 is a 24-port
10/100 managed switch with a variety of hardware and software options. Hardware expansion slots (two
Type IC35) can accept a wide range of Gigabit and 10/100 Mbps media modules:
• 10/100/1000BaseT
• 1000BaseX GBIC
• 1000BaseSX
• 100BaseMMFX
• 100BaseSMFX
See the table below for a description of the 3524 series models that are available.
Model 10/100
Ports Optional MediaModules Description
IC 3524 Base 24 Two IC35 slots
available Managed 24-port 10/100 switch; base
IC 3524-2G 24 Two 1000BaseX
GBIC slots Integrated 1000BaseX GBIC slots
IC 3524-2T 24 Two 10/100/1000
BaseT ports Integrated copper Gigabit ports
Table 1-1 3524 Modules
The system can operate as a stand-alone network or be used in combination with other IntraCore series
switches in the backbone.
1.1 Package Contents
The following items are included in your package:
• Switch
• AC power cord
• Rack mount brackets with screws
• Rubber feet
• Reference Guide
• Getting Started Guide
• User’s Manual (this document, on CD-ROM)
• IntraCore 3524 CD-ROM
Contact your dealer immediately if any of these items are missing.
1.2 LEDs
The system’s LED display allows you to monitor the status of your switch. See Tables 1-2 and 1-3 below for
a complete LED description.

7
Port # LED Color Description
N/A Power/System Green
Off
Power is on
Power is off
1-24(10/100) 10/100 Link Solid Green
Solid Amber
Off
A valid 100 Mbps link has
been established
A valid 10Mbps has been
established
No link has been established
1-24(10/100) Duplex Solid Green
Solid Amber
Full Duplex
Half Duplex
Table 1-2 – Ports 1-24 have two LEDs each
Port # LED Color Description
25,26 Gigabit
(speed) Solid Green
Off
A valid 1000Mbps link has
been established
No link has been established,
or link is at 10/100Mbps rate
25,26 10/100 Link Solid Green
Solid Amber
Off
A valid 100Mbps link has
been established
A valid 10Mbps link has been
established
No 10/100 link has been
established
25,26 Duplex Solid Green
Solid Amber
Full Duplex
Half Duplex
Table 1-3 – Ports 25 & 26 have 3 LEDs each
1.3 Front Panel Description
From left to right, the front panel contains the following: Power and port LEDs; 24 10/100 ports; 2 optional
module slots; and a console port.

8
The switch is field upgradeable for use with 100BaseeFX, 1000BaseSX, 1000BaseX GBIC or
10/100/1000BaseT modules.
1.4 Management and Configuration
There are three different methods by which a user can manage the switch: web, console/telnet, or with
SNMP software. You may prefer using a web browser to be able to configure the switch from any local or
remote computer, via the network, or you may wish to use a console for out-of-band management. SNMP is
an advanced management application, and is mostly automatic, giving you the information without having to
go through an interface step by step (Note: The switch is shipped with BootP support. See Appendix F for
more information on setting up BootP).
Table 1-4 Out-of-Band and In-Band Management
1.4.1 Console Interface
Users can access the switch in a more traditional way by connecting a PC or terminal to the console port or
by telnet across the network. The menus are organized in a manner similar to the web-based interface. A
detailed description can be found in Chapter 3 Configuration. Users must use a console connection to form
a stack (multiple units sharing one IP address). See Chapter 2.11 Using the Stacking Feature for more
details.
1.4.2 Web-Based Interface
With Internet access, users can link directly to the local switch’s home page. Users can configure the switch,
monitor the LED panel, and display statistics graphically. A detailed description can be found in Chapter 5.
Web-Based Interface.
1.4.3 SNMP Management
Since the switch supports SNMP, users can manage the switch with an SNMP-compatible management
station running platforms such as HP OpenView. It also supports a comprehensive set of MIB extensions
along with MIB II, Ethernet MIB, the 802.1D bridge MIB, and 4 groups of RMON. Please see Chapter 3, or
Chapter 6. SNMP Management for more information.
Method Type Description
Console Out-of-Band
Management Local connection to the switch via the console port
Telnet In-Band
Management Remote connection over the network to the switch via the telnet session
HTTP Server In-Band
Management Remote connection over the network to the switch via a Web browser
SNMP-Based
Network
Management
Software
In-Band
Management Remote connection over the network to the switch via any SNMP-based network
management application

9
Chapter 2. Hardware Installation and Setup
The following guidelines will help you to easily install the switch, and to ensure that it has the proper power
supply and environment.
2.1 Installation Overview
Follow these steps to install your IntraCore switch:
1. Open the box and check the contents. See Chapter 1.1 Package Contents for a complete list of the
items included with your IntraCore switch.
2. Install the switch in an equipment or wall rack, or prepare it for desktop placement.
3. Connect the power cord to the unit and to an appropriate power source.
4. Connect network devices to the switch.
See the sections below for more detailed installation instructions.
2.1.1 Safety Overview
The following information provides safety guidelines to ensure your safety and to protect the switch
from damage.
Note: This information is intended as a guideline, and may not include every possible hazard to
which you may be exposed. Use caution when installing this switch.
• Only trained and qualified personnel should be allowed to install or replace this equipment.
• Always use caution when lifting heavy equipment
• Keep the unit clean
• Keep tools and components off the floor and away from foot traffic
• Avoid wearing rings or chains (or other jewelry) that could get caught in the switch. Metal objects
can heat up and cause serious injury to persons and damage to the equipment. Avoid wearing
loose clothing (i.e. ties or loose sleeves) when working around the switch
When working with electricity, follow these guidelines:
• Disconnect all external cables before installing or removing the cover
• Do not work alone when working with electricity
• Always check that the cord has been disconnected from the outlet before performing hardware
configuration
• Do not tamper with the equipment. Doing so could void your warranty
• Examine your work area for potential hazards (I.e. wet floors, ungrounded cables, etc.)

10
2.1.2 Recommended Installation Tools
You will need the following tools and equipment (not included) to install the IntraCore 3524 switch into an
equipment rack:
• Flat head screwdriver
• Phillips head screwdriver
• Antistatic mat or foam
2.1.3 Power Requirements
The electrical outlet should be located near the IntraCore 3524 and be easily accessible. It must also be
properly grounded.
Make sure the power source adheres to the following guidelines:
• Power: Auto Switching 110/240 VAC
• Frequency range: 50/60 Hz
• Maximum Input AC Current: 1.0A at 115 VAC full load
2.1.4 Environmental Requirements
The IntraCore 3524 must be installed in a clean, dry, dust-free area with adequate air circulation to maintain
the following environmental limits:
• Operating Temperature: 0° to 40° C (32° to 104° F)
• Storage Temperature: -20° to 70° C (-4° to 158° F)
• Relative Humidity: 10% to 90% non-condensing
• Storage Relative Humidity: 10% to 95% non-condensing
Avoid direct sunlight, heat sources, or areas with high levels of electromagnetic interference.
2.1.5 Cooling and Airflow
The IntraCore 3524 uses internal fans for air-cooling. Do not restrict airflow by covering or
obstructing air vents on the sides of the switch.
2.2 Installation into an Equipment Rack
To install the unit in an equipment rack, use the following procedure:
Important! Before continuing, disconnect all cables from the IntraCore 3524.
1. Place the IntraCore 3524 on a flat, stable surface.
2. Locate a rack-mounting bracket (supplied) and place it over the mounting
holes on one side of the unit.
3. Use the screws (supplied) to secure the bracket (with a Phillips screwdriver).
4. Repeat the two previous steps on the other side of the unit.
5. Place the switch in the equipment rack.
6. Secure the switch by securing its mounting brackets onto the equipment rack
with the appropriate screws (supplied).
Important! Make sure the unit is supported until all the mounting screws for each bracket are secured to the
equipment rack. Failure to do so could cause the unit to fall, which may result in personal injury or damage
to the unit.

11
2.2.1 Equipment Rack Guidelines
Use the following guidelines to ensure that the switch will fit safely within the equipment rack:
• Size: 17.25 x 10.0 x 1.8 inches (423 x 245 x 39 mm)
• Ventilation: Ensure that the rack is installed in a room where the temperature remains below 40° C
(104° F). Be sure that there are no obstructions, such as other equipment or cables, blocking
airflow to or from the IntraCore 3524 vents
• Clearance: In addition to providing clearance for ventilation, ensure that there is adequate
clearance for servicing the IntraCore 3524 from the front
2.3 GBIC Interfaces
The GBIC Interface is the industry standard for Gigabit Ethernet Interfaces. Some of the benefits of GBIC
include reducing the components needed in your “spares” inventory, a wide variety of manufacturers with
cross-vendor compatibility and competitive prices.
Instructions for installing, removing, and maintaining GBIC modules are provided in following sections.
Model Part Number Standard Media
GBIC 1000SX 99-00549-01 1000BaseSX Multi-mode fiber
GBIC 1000LX 99-00550-01 1000BaseLX Single mode fiber
GBIC 1000T 99-00673-01 1000BaseT Category 5 UTP copper
GBIC 1000TP 99-00647-07 1000BaseT Category 5 UTP copper
Table 2-1 GBIC Modules by Asanté
2.3.1 Installing a GBIC
GBICs are hot swappable. This means that they can be inserted and removed while the unit is powered on.
However, you should allow 40 – 60 seconds for the switch to recognize the module when it has been
installed while the unit is on.
1. Wearing an ESD (electro-static discharge) wrist strap, remove the GBIC module from its protective
packaging.
2. Verify that the GBIC is the correct type for your network (see the table above).
3. Grip the sides of the GBIC with your thumb and forefinger, then insert the GBIC into the slot on the
face of the switch.
4. Slide the GBIC into the slot until you hear or feel a click. The click indicates that the GBIC is locked
into the slot.
5. GBIC 1000SX and GBIC 1000LX modules: Remove the rubber plugs from the end of the GBIC
module. Save them for future use.
6. Attach the appropriate cable.
Note: After installing a GBIC 1000T module, the link LED will light even before a valid cable has been
connected. This is a normal condition for most 1000BaseT GBIC modules.

12
2.3.2 Removing a GBIC
Caution: GBIC 1000T modules run hot under normal operating conditions. When it has been removed from
the system, place it on a heat resistant surface and allow the module to cool before handling.
Note: Unnecessary removals/insertions of a GBIC module will lead to premature failure of the GBIC. The
rated duty cycle for a GBIC module is 100 to 500 removals/insertions.
Follow the steps below to remove a GBIC interface from a Gigabit Ethernet module:
1. Disconnect the cable from the GBIC module.
2. Release the GBIC from the slot by simultaneously squeezing the locking tabs on both sides of the
GBIC.
3. Slide the GBIC out of the slot.
4. GBIC 1000SX and GBIC 1000LX modules: Install the rubber plugs in the GBIC optical bores, and
place the GBIC in protective packaging.
2.3.3 GBIC Care and Handling
Follow these GBIC maintenance guidelines:
• GBICs are static-sensitive. To prevent ESD damage, follow your normal board and component
handling procedures. Wear an ESD wrist strap
• GBIC 1000SX and GBIC 1000LX modules are very sensitive to dust and contaminants. When they
are not connected to a fiber-optic cable, install the rubber plugs in the optical bores
• The ferrules of the optical connectors may pick up debris that can obstruct the optical bore. Use an
alcohol swab or equivalent to clean the ferrules of the optical connector
2.4 Installing Optional Hardware Modules
Follow the steps below to install your media modules (10/100/1000BaseT, 1000BaseX GBIC, 1000BaseSX
or 100BaseFX):
1. Using a flat-head screwdriver (not included), remove the slot cover plate
from the switch.
2. Touch a grounded, metal object to discharge any static electricity on your
body, and then remove the module from its protective packaging (being
careful not to touch any board components or connectors).
3. Slide the module firmly into the module slot until it has
clicked into place. The module’s faceplate should be
flush with the front panel of the switch.
4. Replace the screws to secure the module, being
careful not to over-tighten the screws.
5. Connect network cables to the module port.
6. Restore power to the switch if necessary, or reset the
switch.
2.5 Connecting Power
Use the following procedure to connect power to the IntraCore 3524:
Important: Carefully review the power requirements (Chapter 2.1.3) before connecting power to the
IntraCore 3524.
1. Plug one end of the supplied power cord into the power connector on the back of the unit.
2. Plug the other end into a grounded AC outlet.
3. Turn on the switch’s power. The Power LED will begin its initialization process.
The front panel LEDs blink and the Power LED illuminates when it has initialized. The IntraCore 3524 is
ready for connection to the network.

13
Important: If the power does not come on, check the next section to ensure you are using the correct
cabling.
2.6 Connecting to the Network
The switch may be connected to an Ethernet network with the unit powered on or off. Use the following
procedure to make your network connections:
1. Connect your network devices to the IntraCore 3524, following the cable guidelines outlined below.
2. After the unit is connected to the network, it can be configured for management capabilities (see
the following chapters for information on configuration).
2.6.1 10/100BaseT Ports Cabling Procedures
The 24 10/100 ports on the IntraCore 3524 allow for the connection of 10BaseT or 100BaseTX network
devices. The ports are compatible with IEEE 802.3 and 802.3u standards.
Important: The IntraCore 3524 must be located within 100 meters of its attached 10BaseT or 100BaseTX
devices.
Use the following guidelines to determine the cabling requirements for your network devices:
• Connecting to Network Station: Category 5 UTP (Unshielded Twisted-
Pair) straight-through cable (100 meters maximum) with RJ-45 connectors
• Connecting to Repeater/Hub/Switch’s Uplink port: Category 5, UTP
straight-through cable (100 meters maximum) with RJ-45 connectors
Note: There is no uplink port on this switch. All 10/100 ports on this switch are
auto-sensing MDI/MDI-X. This advanced feature means that the 10/100 ports will
automatically determine whether the device at the other end of the link is a hub, switch or workstation, and
adjust its signals accordingly.
Although 10/100BaseT requires only pins 1, 2, 3 and 6, Asanté strongly recommends cables with all 8 wires
connected as shown in Table 2-1 below.
1000BaseT requires that all four pairs (8 wires) be connected correctly, using Category 5 or better
Unshielded Twisted Pair (UTP) cable (to a distance of 100 meters). Table 2-1 shows the correct pairing of all
eight wires.
Pin Number Pair Number & Wire Colors
12 White/Orange
22 Orange/White
33 White/ Green
41 Blue/White
51 White/Blue
63 Green/White
74 White/Brown
84 Brown/White
Table 2-2 Pin Numbers and Wire Colors

14
2.6.2 Gigabit Ethernet Ports Cabling Procedures
Cabling requirements for the optional hardware modules depend on the type module that has been installed.
Use the following guidelines to determine the cabling requirements for your modules:
• 1000BaseSX GBIC: Cables with SC-type fiber connectors; 62.5-micron multimode fiber (MMF)
media up to 275 meters (902 feet) long, or 50-micron MMF media up to 550 meters (1805 feet)
long
• 1000BaseLX GBIC: Cables with SC-type fiber connectors; 10-micron single mode fiber media up to
5 kilometers (3.1 miles) long
• 1000BaseLX Long Haul GBIC: Cables with SC-type fiber connectors; 10-micron single mode fiber
media up to 100 kilometers (62 miles) long
• 1000BaseT: Category 5 or better Unshielded Twisted Pair (UTP) cable to a distance of 100 meters
(328.1 feet)
2.7 Setup
The following sections describe the steps for setting up the switch for basic configuration, and putting into
place basic security measures (setting up password protection, changing from the default IP address and
configuring the SNMP host table).
In order to configure the switch, you will need to connect to it through a console (out-of-band management),
through your web browser, or through a telnet session.
2.7.1 Connecting to a Console
When attaching a workstation to the device, a standard straight-through CAT5 cable may be used, even
when the workstation is attached via a patch panel. No crossover cable is needed with the MDX/MDI ports.
It is recommended that the switch be kept off the network until proper IP settings have been set.
To connect the switch to a console or computer, setup the system in the following manner:
1. Plug power cord into the back of unit.
2. Attach a straight-through serial cable between the RS232 port and a COM port on the PC.
3. Setup a HyperTerminal (or equivalent terminal program) in the following manner:
• Under the Connect To tab, choose the appropriate COM port (COM1, COM2, etc)
• Under the Settings tab, choose VT100 for Emulation mode
• Select Terminal keys for Function, Arrow and Ctrl keys. Be sure the setting is for Terminal keys,
NOT Windows keys
• Back under the Connect To tab, press the Configuration button

15
• Set the data rate to 9600 Baud
• Set data format 8 data bits, 1 stop bit and no parity
• Set flow control to NONE
Now that terminal is setup correctly, power on the switch (boot sequence will display in terminal).
2.7.2 Connecting Via the Web Browser
To connect to the switch via your web browser, you must first have configured your computer’s IP address to
be on the same IP address subnet as the switch (The switch’s default IP is 192.168.0.1). For more
information on how to configure your TCP/IP settings, please refer to your computer manufacturer’s user’s
manual.
You may now launch your web browser and enter the switch’s default IP address into the address field. The
Introduction page will appear, and you may proceed through the pages to configure each variable. See
Chapter 5. Web-Based Interface for more information on configuring the switch via your web browser.
2.7.3 Connecting Via Telnet
To connect to the switch via a telnet session, you must first have configured your computer’s IP address to
be on the same IP address subnet as the switch (192.168.0.X). For more information on how to configure
your TCP/IP settings, please refer to your computer manufacturer’s user’s manual.
You may now run a telnet session to configure and manage your switch. The Enter Password screen will
appear. Enter the default password to access the Main Menu, and proceed to select the variables that you
wish to configure. See Chapter 3. Configuration for more information on configuring the switch via telnet.
2.8 Changing the Password
The default password (which is Asante, and is case sensitive), may allow immediate access to ANYONE on
the network. To protect your switch from unauthorized changes to the configuration, you must change the
administrator’s password. It can only be changed through the console or telnet interfaces.
To change the administrator’s password, follow these steps:
1. Establish a telnet session, and type Asante at the password prompt.
2. Press Enter to proceed.
3. Type
cto access the Configuration menu.
4. Type
uto access the User Interface Configuration sub-menu.
5. Type
pto select Change Administrator’s Password.
6. Type the current password (Asante) and press Enter.
7. Type the new password and press Enter.
8. Re-type the new password to confirm your entry, and press Enter.

16
2.9 IP Assignment
To change the IP address of the switch from the default setting:
1. Access the System IP Configuration menu by typing iin the Configuration menu.
2. Type the command letter of the option you want to change.
3. Type the new address at the prompt.
To cancel a change, type ctrl-c at the command prompt.
4. Press Enter. The IP setting change for the switch takes effect.
5. Type qto quit and return to the Configuration menu.
When the reset is complete the switch should be seen on your network. If not, check the IP information
again to ensure that all the data is correct.
2.10 SNMP Management
The SNMP Configuration Menu allows you to configure the unit’s read and write community strings, and to
enable or disable authentication traps. This menu also allows you to specify which of your network
management stations will receive traps from the switch.
The n option in the Configuration Menu displays the SNMP (Simple Network Management Protocol)
Configuration Menu, as shown below.
IntraCore SNMP Configuration Menu
SNMP Read Community: public
SNMP Write Community: private
Trap Authentication: Disabled
SNMP Trap Receivers:
IP Address Community
1. xxx.xxx.xxx.xxx public
2. <empty> <empty>
3. <empty> <empty>
4. <empty> <empty>
<Cmd> <Description>
r Set SNMP Read Community
w Set SNMP Write Community
t Toggle Trap Authentication Enable/Disable
a Add/Update SNMP Trap Receiver
d Delete SNMP Trap Receiver
q Return to previous menu
Command>
Important! Be sure to change the SNMP community strings in order to prevent unauthorized access to
management information. See Chapter 3 for details.
Also, see Chapter 6. SNMP Management for more detailed information on the SNMP protocol.

17
2.11 Using the Stacking Feature
The 3524 v.1.1 offers a stacking feature that allows the user to stack up to eight units, all sharing one IP
address of the master switch (unit #1). This is an efficient and cost-effective way to add ports as needed.
The following lists the characteristics of stacking that the user needs to be aware of:
• Uses any physical media supported by IC 3524: copper or fiber, Fast Ethernet or Gigabit Ethernet
(see the stacking kit {sold separately} shown below); or a special, cost-effective Stacking Kit
(available Q2-02, not shown)
Stacking Kit
• All stacked units are managed through connection to the master switch, via console, telnet or web
interfaces
Note: While the user may manage the stack via console, telnet or web interface, the initial
formation of the stack may only be done by connection to a console.
• The switches need no extra software, but they must all have the 1.1 firmware installed (see
Chapter 3.14 for firmware upgrade instructions)
Follow the steps below to install (build) a stack:
1. Physically stack the units, in an equipment rack, or on a flat, stable surface (Asanté recommends
that the stack is formed from the bottom up for ease of adding additional units).
2. Units are connected via the Gigabit ports (see section 2.4 for instructions on installing the optional
modules). Starting with the first unit in the stack (the bottom unit, in the photo below), connect the
Ethernet cable from Gigabit port #26 to the Gigabit port #25 of the next unit and continue the
connections to the last unit in the stack. The result is a stack with nx 24 10/100 ports and 2 Gigabit
ports, where nis the number of units in the stack (up to eight).

18
3. For stacking operation, the stacking feature must first be enabled on each unit (by default, stacking
is disabled). Establish a console connection to the first unit. Type kin the Configuration Menu to
access the Stacking Management menu. Type tto toggle the switch from “disabled” to “enabled”.
Repeat for all remaining units.
IntraCore 3524 Configuration Menu
<Cmd> <Description>
a System Administration Configuration
i System IP Configuration
b Bootstrap Configuration
n SNMP Configuration
p Port Configuration
s Spanning Tree Configuration
d Unicast Forwarding Database Configuration
t Security Management
v VLAN Management
c IP Multicast Traffic Management
m Port Mirroring Configuration
f File Up/Downloading Configuration
k Stack management
r System Reset Options
l System Log
u User Interface Configuration
y System Utility
q Return to previous menu
Command>
IntraCore 3524 Stack Management Configuration Menu
Stacking : ENABLED
Stacking Operation (1 of 8)
Stack IP : xxx.xxx.xxx.xxx
Stack MAC : 00:00:94:CC:C7:6D
<Cmd> <Description>
s Stacking Multiple Modules
d Stand Alone Operation
t Toggle Stacking Enable/Disable
q Return to previous menu
Command>
4. After all units have had stacking enabled, connect the console to the first unit (the Master unit).
5. Power cycle the whole stack, or, if the units are to be powered up separately, power the Master
last.
6. Go to the Master’s Stack Management menu and type sto begin the automatic formation of the
stack.
7. After the stack is formed, configuration and operation of the stack can begin (see Chapter 3
Configuration and Chapter 4 Advanced Configuration for more details).

19
Chapter 3. Configuration
This chapter describes the log in procedure and configuration of the switch via the console or telnet
interfaces. For information on configuring the switch via your web browser, see Chapter 5. Web-Based
Management.
Note: The screens shown are for firmware version 1.1. Earlier versions may have slightly different screens,
but will not effect the basic configuration instructions.
Logging In
When you connect to the Local Management Interface, the “Enter Password” prompt appears. Enter your
password, and then press Enter. The Main Menu appears.
Important! The default password is Asante. The password is case-sensitive; enter it exactly as shown.
After logging in, the Main Menu appears, as shown below.
==============================================================
IntraCore 3524 Remote Management System Version 1.10
Compiled Date: Dec 05 2001 13:53:58
Asante Technologies, Inc.
Copyright (c) 2001 Asante Technologies, Inc.
==============================================================
Main Menu
<Cmd> <Description>
g General Information
c Configuration
s Statistics
q Close Connection
Command>
From the Main Menu, you can access three submenus:
• General Information
• Configuration
• Statistics
If you are using Telnet, a fourth option for closing the connection is available as well.
Accessing a Submenu
To access a submenu, type the command letter that corresponds with the option you need to use. For
example, type gfor General Information.
Note: When configuring certain options on multiple units (stacked switches), the System Unit Map screen
may appear, like the one below. Type the number of the unit to be configured and press Enter.

20
System Unit Map
=================
Please select one of the following slots
Slot Description (Unit Type)
---- -------------------------------------------
1 IntraCore 3524 Unit
2 IntraCore 3524 Unit
3 IntraCore 3524 Unit
4 IntraCore 3524 Unit
5 IntraCore 3524 Unit
6 IntraCore 3524 Unit
7 IntraCore 3524 Unit
8 IntraCore 3524 Unit
Enter Unit Number (1 - 8) >
Exiting a Submenu
To exit a submenu, type q.
To exit a command line without changing the configuration setting (e.g., the “Set Password” option in the
User Interface Configuration Menu), press ctrl-c.
3.1 General Information
The General Information Screen displays the current operating information of the IntraCore 3524, such as its
name, IP address, and boot information.
To view General Information, type gfrom the Main Menu. A screen similar to that below appears.
IntraCore 3524 General Information Menu
System up for: 001day(s), 17hr(s), 27min(s), 54sec(s)
Software Version
Bank 1 Image Version/Date: 1.10/Dec 05 2001 13:54:06
Bank 2 Image Version/Date: 1.10/Dec 05 2001 13:54:06 (Running)
System Information
PROM Image Version/Date: 1.03D/Oct 06 2001 15:29:58
DRAM Size: 16.0MB Flash Size: 2.0MB
Config NVRAM Size: 64KB Console Baud Rate: 9600 bps
Administration Information
System Name: Test Stack
System Location:
System Contact:
System MAC Address, IP Address, Subnet Mask and Router
MAC Address: 00:00:94:CC:C7:6D
IP Address: xxx.xxx.xxx.xxx
Subnet Mask: 255.255.255.0
Router: 0.0.0.0
Bootstrap Configuration
Boot Load Mode: LOCAL
Press any key to continue...
Note:The information displayed on this screen is read-only.
To exit the General Information Screen, press any key on your keyboard.
3.2 Configuration Menu
The Configuration Menu allows you to manage and configure switch and each of its ports.
To access the Configuration Menu, type cfrom the Main Menu. The Configuration Menu appears, as shown
below (from a telnet session):