Asko HIG1944MF User manual

05
L1 (W) L2 (W) L3 (<W) Total load (W)
HIG1944 3700 3700 5 7400
A
B
C
A (mm) B (mm) C (mm) D (mm) E (mm)
HIG1944 904 522 54 265 180
Rangehoods and exhaust fans shall be
installed in accordance with
manufacturers instructions.
For an overhead exhaust fan A>750 mm!
This appliance must be earthed
The electrical connection must comply with national and local regulations.
Connected load
A (>mm) B (mm) C (mm) D (>mm) E (>mm) F (>mm) G (>mm) H (>mm)
HIG1944 600 860 490 60 40 50 66 100
E
E/F
C
D
G
B
A
F
H
oven
Accessibility!
Gas connection
Important information
Pictograms used
Electrical connection
Installation instructions
Combination hob induction/gas
Au
The fitting of the appliance should only be carried out by a authorised person/licensed gasfitter. Please read the safety regulations.
See the data plate for information regarding the total gas consumption, gas type and gas pressure.
Preparations for installation
The gas connection must comply with national and local regulations.
The hotplate can be connected with rigid pipe as specified in
AS/NZS 5601.1current edition.
When the appliance is connected with a hose assembly,
the supply point shall be accessible with the appliance installed.
1/2” ISO 228 / 1/2" ISO 7-1
y
y
x
x
>60º C
<60º C
oven
Y:
metal
Gas supply valve
shall be accessible
X:
safety hose
Gas supply valve
shall be accessible
A
B
min.
B+D
C
E
D
Free space around appliance
A (>mm) C (>mm) D (>mm) E (> mm)
650 450 40 120

Ventilation
Consult the wiring diagrams on the underside of the appliance Make the required connections on the connecting block.
The following appears on initial use:
Error code F04 -066 / No gas
- Check the gas supply
- Switch the appliance off and on using key button
- Re-ignite
- Repeat this procedure until the burner is lit
05
05
05
05
PTFE tape
1/2“ ISO 228
1/2“ ISO 7-1
Gas connection
05
C
C
Placing sealing tape
Worktop
min. 200 cm2
1
2
3
3
Electrical connection
Check that the connections are gastight.
150
Ldrawer
L
min.100 mm
4x1.5mm
2N 380-415V 50/60Hz - 2x 16A
2 phases - 1 neutral
Cross sectional area Cross sectional area
1 phase - 1 neutral
1N 220-240V 50/60Hz - 1x 32A
3x4mm
2
5x1.5mm
22
Cross sectional area
3N 380-415V 50/60Hz - 3x 16A
3 phases - 1 neutral
415V 415V
415V
240V
240V
240V
240V
240V
240V
415V
GAS BURNER INJECTOR BURNER RATE GAS PRESSURE
BURNER (MJ/h) (kPa)
N.G. Wok (inner) 1.20 + 0.66 8.80 1.0
Wok (outer) 2.10 + 0.66 19.70
ULPG Wok (inner) 0.63 + 0.40 8.50 2.75
Wok (outer) 1.00 + 0.40 15.75
Fitting of appliance regulator
for Natural gas or test point
adaptor for LPG.
Check and set the gas pressure
with appliance operating!
564197
564197
564197 / VER 2 / 13-02-2017