ASRock Industrial iEP-9010 Series User manual

iEPF-9000S-EX4
iEPF-9002S-EX4
iEP-9000E
iEP-9002E
User Manual
Version 1.0
Published August 2022
Copyright©2022 ASRock Industrial Computer Corp. All rights reserved.
iEP(F)-9010 Series
iEP(F)-9020 Series
User Manual

ii iii
Version Date Description Page
1.00 2023/03 Initial release
1.10 2023/12 Update all
1.11 2024/02
1. Updated Website Link
2. Updated Important Safety Instructions
3. Updated Chapter 1~4
P. iii~vi, 1, 3, 5~6,
8~10, 16~19, 34, 38,
44, 46~47, 54, 60~61,
67~68, 76~77, 79, 91,
126~127
Copyright©2022 ASRock Industrial Computer Corp. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or translated
in any language, in any form or by any means, except duplication of documentation by the
purchaser for backup purpose, without written consent of ASRock Industrial Computer
Corp.
Products and corporate names appearing in this documentation may or may not be
registered trademarks or copyrights of their respective companies, and are used only for
identication or explanation and to the owners’ benet, without intent to infringe.
Disclaimer:
Specifications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock Industrial Computer Corp. ASRock Industrial
Computer Corp. assumes no responsibility for any errors or omissions that may appear in
this documentation.
With respect to the contents of this documentation, ASRock Industrial Computer
Corp. does not provide warranty of any kind, either expressed or implied, including but
not limited to the implied warranties or conditions of merchantability or fitness for a
particular purpose.
In no event shall ASRock Industrial Computer Corp., its directors, ocers, employees, or
agents be liable for any indirect, special, incidental, or consequential damages (including
damages for loss of prots, loss of business, loss of data, interruption of business and the
like), even if ASRock Industrial Computer Corp. has been advised of the possibility of such
damages arising from any defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause
undesired operation.

ii iii
Important Safety Instructions
For user safety, please read and follow all instructions, Warnings, Cautions, and Notes
marked in this manual and on the associated device before handling/operating the device,
to avoid injury or damage.
1. Read these safety instructions carefully.
2. Retain this user manual for future reference.
3. Read the Specifications section of this manual for detailed information on the
recommended operating environment.
4. Disconnect the equipment from all AC outlets before cleaning. Use only a damp cloth
for cleaning. Do not use liquid or sprayed detergent.
5. Place the equipment on a reliable surface during installation. Dropping or letting the
equipment fall may cause damage.
6. Do not leave the equipment in an environment with a storage temperature of below
-40 °C (-40 °F) or above 85 °C (185 °F) as this may cause damage. The equipment
should be stored in a controlled environment.
7. Ensure that the voltage of the power source is correct before connecting the
equipment to a power outlet.
8. Position the power cord away from high-trac areas. Do not place anything over the
power cord.
9. If the equipment is not used for a long time, disconnect the equipment from the
power source to avoid damage from transient over-voltage.
10. All cautions and warnings on the equipment should be noted.
11. To avoid electrical shock and/or damage to the device:
• Keep the device away from water or liquid sources.
• Keep the device away from high heat or humidity.
• Keep device properly ventilated (do not block or cover ventilation openings).
• Always use designated voltage and power source settings.
• Always install and operate the device near an easily accessible electrical outlet.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock Industrial Website: https://www.ASRockInd.com

iv v
• Secure the power cord (do not place any object on/over the power cord).
• Only install/attach and operate the device on stable surfaces and/or designated
mountings.
• e power cord must be connected to a socket or outlet with a ground connection.
12. If one of the following occurs, have the equipment checked by service personnel:
• e power cord or plug is damaged.
• Liquid has penetrated into the equipment.
• e equipment has been exposed to moisture.
• The equipment is malfunctioning or does not operate according to the user
manual.
• e equipment has been dropped and damaged.
• e equipment shows obvious signs of breakage.
13. Never attempt to repair the device, which should only be serviced by qualified
technical personnel using suitable tools.
14. Any unverified component may cause unexpected damage. To ensure correct
installation, always use the components (e.g., screws) provided in the accessory box.
15. This equipment is not suitable for use in locations where children are likely to be
present.
16. e equipment should only be installed in a restricted access area.
17. Restricted Access Location:
e device must be installed only in a server room or computer room where:
• Access can only be gained by service persons or by users who have been
instructed about the reasons for the restrictions applied to the location and about
any precautions that shall be taken.
• Access is through the use of a tool or lock and key, or other means of security, and
is controlled by the authority responsible for the location.
• Leave enough clearance (25 inches in the front and 30 inches in the back of the
rack) to allow the front door to be opened completely and to allow for sucient
airow.
• is product is intended for installation only in a Restricted Access Location.
• is product is not suitable for use with visual display devices in the workplace
according to §2 of "the German Ordinance for Work with Visual Display Units".
18. e equipment is intended to be supplied by the external power source (UL listed/
IEC 60950-1/ IEC 62368-1 approved) whose output complies with ES1/SELV. To
reduce potential safety issues, only the AC adapter provided with the product, a
replacement AC adapter provided by ASRock Industrial or an agency, or an AC
adapter purchased as an accessory from ASRock Industrial or an agency should be
used with the product.
19. This power adapter (FSP330-AAAN3) is intended to be supplied based on a UL-
certied and suitable for use at an operating/storage temperature of 0 °C (32 °F)~
40 °C (104 °F)/ -20 °C (-4 °F)~80 °C (176 °F), and the current output is rated 24Vdc

iv v
13.75A. If you need further assistance, contact ASRock Industrial for additional
information.
20. e ambient temperature of the iEP-9010E & iEP-9020E series: 70 °C (158°F) max.;
the ambient temperature of the iEPF-9010S & iEPF-9020S series: 75 °C (167°F) max.
21. The terminal block is suitable for V+V-, with 3 units each (16~18AWG), totaling 6
units. e torque value is 0.69Nm. Please ensure the use of copper conductors only.
Kindly note that installation must be carried out by a professional.
22. LAN port must use shielded LAN cable.
Replaceable Batteries
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
CAUTION
e equipment is equipped with a battery-powered real-time clock circuit. ere is a risk
of explosion if a battery is incorrectly replaced. Replace only with the same or equivalent
type as designated by the manufacturer. Discard all used batteries according to the
manufacturer's instructions.
LITHIUM-METAL BATTERY WARNING
Danger of explosion if the battery is incorrectly replaced. Replace only with the same or
equivalent type designated by the manufacturer. Dispose of used batteries according to the
manufacturer's instructions.
WARNING
All interconnection to the EUT is intended for indoor locations, and as a result, the PoE
network interconnected to the EUT is considered ES1/SELV, designed exclusively for
connection to the PoE network without routing to the outside plant.
WARNING
Input voltage rated 9~36V, 30~18A.
Packing: e unit should be carried with both hands and handled with care.
Maintenance: Use only approved products or a dry applicator to clean and maintain the
surfaces.

vi vii
e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
Contact Information
If you need to contact ASRock Industrial or want to know more about ASRock Industrial,
you’re welcome to visit ASRock Industrial’s website at https://www.ASRockInd.com; or
you may contact your dealer for further information.
ASRock Industrial Incorporation
Email: Inf[email protected]

vi vii
Contents
Chapter 1 Introduction 1
1.1 Key Features 1
1.2 Package List 4
1.3 Order Information 6
1.4 Optional Items 7
1.5 Serial Number Label 7
1.5.1 Serial Number Label Location 7
1.5.2 Serial Number Label Illustration 7
1.6 Specications 8
1.7 CPU Support List 24
1.8 Dimensions and Size 34
1.9 Block Diagram 41
Chapter 2 Product Overview 43
2.1 System Front Panel 43
2.1.1 System Front Panel I/O Functions 45
2.2 HDD Panel 56
2.3 Drive Tray LEDs 57
2.4 Motherboard 58
2.4.1 Motherboard Layout for iEP(F)-9010 & 9020 Series 58
2.4.2 Motherboard Layout for iEP(F)-9012 & 9022 Series65

viii ix
2.4.3 Ignition Control 71
2.5 Other Boards 74
2.5.1 DSC-SATA001-WT or DSC-SATA002-WT 74
2.5.1.1 DSC-SATA001-WT Layout and I/O
Connectors 74
2.5.1.2 DSC-SATA002-WT Layout and I/O
Connectors 75
2.5.2 DSC-PSE002-WT Layout and I/O Connectors 76
2.5.3 DSC-COMDIO002-WT Layout and I/O Connectors 77
2.5.4 DSC-COMDIO003-WT Layout and I/O Connectors
(Optional) 79
2.5.5 DSC-SLOT003-WT Layout and I/O Connectors
(9010S/9012S & 9020S/9022S Only) 82
2.5.6 DSC-SLOT002-WT Layout and I/O Connectors
(Optional) 86
2.5.7 VGA-PWR Layout and I/O Connectors (Optional) 89
Chapter 3 Hardware Installation and
Maintenance 90
3.1 How to Disassemble the System 91
3.2 How to Install the CPU 96
3.3 How to Install the Hard Disk Drive 100
3.4 How to Install the SIM Card 102
3.5 How to Install the Desk Mount Bracket 104
3.6 How to Install the Rubber Foot 105
3.7 How to Install the Memory Module with Heatsink 106
3.8 How to Install the M.2 SSD with Heatsink 107

viii ix
3.9 How to Install the Riser Card 108
3.10 How to Install the Mini-PCIe Card 111
3.11 How to Install the WiFi Module (M.2 Key E Socket
(2230)) 112
3.12 How to Install the 4G / 5G module (M.2 Key B Socket
(2280/3042/3052)) 113
3.13 How to Install the WiFi/4G/5G Antennas and Cables 114
3.13.1 Antennas 114
3.13.2 SMA Cables 115
Chapter 4 UEFI Setup Utility 117
4.1 Introduction 117
4.1.1 Entering BIOS Setup 117
4.1.2 UEFI Menu Bar 118
4.1.3 Navigation Keys 119
4.2 Main Screen 120
4.3 Advanced Screen 122
4.3.1 CPU Conguration 123
4.3.2 Chipset Conguration 125
4.3.3 Intel(R) Time Coordinated Computing 127
4.3.4 Storage Conguration 129
4.3.5 Super IO Conguration 130
4.3.6 ACPI Conguration 133
4.3.7 USB Conguration 134
4.3.8 Trusted Computing 135
4.4 Hardware Health Event Monitoring Screen 137

x 1x 1
4.5 Security Screen 138
4.6 Boot Screen 139
4.7 Exit Screen 140
Chapter 5 Appendix 141
Appendix 1 Power Consumption 141
Appendix 2 Link to the API Library 142
Appendix 3 How to Install Power Supply or Power
Adapter 142