Assa Abloy OH1000 Series User manual

Template No.
T-OH1000
Rev. 04/24/12
NOTE: Rockwood reserves the right to make product changes and is not
responsible for obsolete template errors. To ensure your template is current,
please visit our website at www.rockwoodmfg.com or call us at 800-458-2424.
OH1000 Series Surface Mounted Door Stops and Holders
300 Main Street • Rockwood, PA 15557 • P: 800-458-2424 • F: 800-922-9212 • Website: www.rockwoodmfg.com
©04.12 RMC
Rev. A
INSTALLATION INSTRUCTIONS
1. Select proper dimensions from chart on back side
of page.
2. Locate "A" and "B" dimensions on door and frame.
3. Install jamb bracket on stop strip as shown.
4. Position channel on door with shock end located
towards pivot. Drill 5/16 (7.9) dia. sex bolt hole, "A"
dimension, 3/4 (19) down from stop strip as shown.
5. Install channel on door with "A" dimension sex bolt.
Locate "C" dimension sex bolt hole making sure
that channel is horizontal and parallel with stop
strip. Drill 5/16 (7.9) dia. sex bolt hole and finish
installing holder.
NOTES:
• All hollow metal frames should be properly
reinforced with 3/16" (4.8) min. thickness x 12"
(304.8) min. length reinforcement plates.
• All hollow metal doors should be properly
reinforced.
• All drilling and tapping to be done by field men.
• Suggest mounting door stop or holder first and then
other hardware to clear. Contact factory if
interference results with other hardware.
• Jamb bracket to be on same centerline as channel.
• Intermediate bracket #12 x 3/4" FS MS.
• All dimensions are given in inches (mm).
FASTENERS:
Jamb: #12 x 1-1/2" FH WS or #12-24 x 1/2" FH MS (4 Places)
Door: #12-24 x 1-1/2" FH MS and 5/16" Dia. Sex Bolt (2 Places)
Not To Scale
CAUTION: Note location
of swing clear hinge
centerline to determine
"A" and "B" dimensions.

Template No. T-OH1000
Rev. 04/24/12
OH1000 Series Surface Mounted Door Stops and Holders
300 Main Street • Rockwood, PA 15557 • P: 800-458-2424 • F: 800-922-9212 • Website: www.rockwoodmfg.com
©02.12 RMC
Rev. A
NOTE: Rockwood reserves the right to make product changes and is not responsible for obsolete template errors.
To ensure your template is current, please visit our website at www.rockwoodmfg.com or call us at 800-458-2424.
When using center hung pivots, check pivot manufacturer's compatibility prior to specifying.
OH1000 Series Surface Mounted Door Stops and Holders
1. See other side for installation instructions.
2. Select proper dimensions noted below.
3. Add 5/8" to "A" dimension for dead stop.
4. All dimensions given in inches.
*Butt mounting only.
Reversible, non-handed.
TO SELECT DEGREE OF STOP
1. With a 3/16 hex key wrench, loosen the set screw in the
shock block.
2.Open door to desired degree of opening.
3.Slide shock block and spring until the spring touches
slider cam.
4.Tighten set screw.
5. Verify door opening position and re-adjust, as needed.
Stop Multi Door Opening A B C
1001S 1001M 18 - 24 1-3/16 3-9/16 14-13/16
1002S 1002M 24-1/16 - 30 3-3/4 4-3/16 16
1003S 1003M 30-1/16 - 36 6-9/16 5-3/8 17-3/4
1004S 1004M 36-1/16 - 42 9-13/16 7-1/16 20-3/16
1005S 1005M 42-1/16 - 48 13-3/4 8-5/16 22
Device Number
1 3/4 - 2 1/4
Butts
&
3/4 Offset
Pivot
Stop Multi Door Opening A B C
1001S 1001M 21 - 26-1/2 1-5/8 4 14-13/16
1002S 1002M 26-9/16 - 32 4-7/16 4-7/8 16
1003S 1003M 32-1/16 - 38 7-3/16 6 17-3/4
1004S 1004M 38-1/16 - 45 10-3/8 7-5/8 20-3/16
1005S 1005M 45-1/16 - 48 14-5/16 8-7/8 22
Center Hung
Device Number