Astonica 50102667 User manual

Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
®
Model No: 50102667
Kamilah 20" Round Occasional Table
Instruction Manual
For warranty information, please refer to the back page of
this instruction manual.
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
NOTE: This product is intended for residential, non-commercial use.
Made in China
©2012 World Factory, Inc.
Distributed by:
World Factory, Inc.
Westlake, TX 76262
051112rev1
For Manuals, Replacement Parts or Customer Service visit:
www.ezreplacement.com
Limited Warranty
World Factory, Inc. Products for Home Use
World Factory, Inc. (Seller) warrants to the original Buyer only, that each Astonica Product will be free
from defects in material and workmanship for a period of one (1) year from date of purchase.
SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH
ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE SELLER
WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY FROM
REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER
MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This
warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to
normal use or weathering. To make a claim under this Limited Warranty, you must return the complete
product with proof of purchase, transportation prepaid, to any World Factory, Inc. authorized service
center. Call 1-888-422-7800 or visit: ezreplacement.com for the location of the nearest authorized
service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)
YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF
PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such
provision shall not affect any other provision herein, this Limited Warranty shall be construed as if
such invalid and/or unenforceable provision had never been contained herein.
This warranty gives you special legal rights, and you may also have other rights which vary from state
to state.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all
prior agreements, arrangements, or understandings between the parties relating to product warranty.

A Table Top 1
B Upper Legs (Hole placement closest to table top) 2
C Lower Legs 2
D Bolt 4
E Nut 4
F Plastic Bushing 4
G Nut Cover 4
H Bolt Cover 4
I Hex Key 1
J Nut Wrench 1
ASSEMBLY INSTRUCTIONS
PARTS & HARDWARE LIST
PART # DESCRIPTION QUANTITY
A
A
A
B
B
B
C
C
C
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
Parts Detail
NOTE: This product is intended for residential, non-commercial use.
12
1. (SEE FIGURE 1) Place table top (A) on a flat
non-scratch surface. Insert table legs (B) into
leg guides in rim of table top (A) adjacent from
each other.
2. (SEE FIGURE 2) Secure table legs (B) by
inserting the plastic bushing (F) in between the
legs and threading the bolt (D) through the leg
holes, bushing (F), and nut (E) using the
hex key (I) and wrench (J). Repeat step 1 and 2
for other two legs (C). Turn table upright and
tighten fasteners.
3. (SEE FIGURE 3) Apply bolt covers (H) and nut
covers (G) to exposed bolts and nuts.
E
E
D
D
F
F
G
Figure 1
HI J
Figure 2
Figure 3
HG