Astonica 50104078 User manual

IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
CONTACT OVERSTOCK.COM CUSTOMER SERVICE AT
1-800-843-2446
200206rev1
Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
CONTACT CONSUMER SUPPORT AT
1-800-843-2446
Made in China
Distributed by:
Overstock.com
6350 South 3000 East
Salt Lake City, UT 84121
OV SKU No. 10090642-000-000
Model No. 50104078
Calabria 42" Square Table
Instruction Manual
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
NOTE: This product is intended for residential, non-commercial use.
Warranty Information:
Products for Home Use
For warranty issues please contact the retailer directly at:
1-800-843-2446
or
www.Overstock.com

PARTS LIST
PART # DESCRIPTION QUANTITY
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
CONTACT CUSTOMER SERVICE AT
1-800-843-2446
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
A Table Top 1
B Table Leg 4
C Leg Connector Bracket 1
D Short Bolt 8
E Long Bolt 8
F Hex Nut 8
G Metal Washer 24
H Lock Washer 8
J Plastic Bolt Cap 16
K Plastic Nut Cap 8
L Angle Wrench 1
M Hex Wrench 1
NOTE: This product is intended for residential, non-commercial use.
Parts Detail
1
A
BC
DEFG H J
KLM

ASSEMBLY INSTRUCTIONS
Figure 1
CAUTION: Do not over tighten
 hardware.
Install Table Legs
1.(SEE FIGURE 1) Place table top (A)
 upside down on non-scratch surface.
2.Align one table leg (B) with corner of
 table top (A).
3.Attach table leg to table top using
 two short bolts (D), lock washers (H
 and metal washers (G). Loosely tighten
 hardware using angle wrench (L).
4.Repeat steps 1 - 3 with remaining
 table legs.
3
Figure 2
C
D
E
F
G
B
AH
J
K
LM
B
A
C
B
G
D
H
G
C
B
G
E
G
K
F
G
K
F
G
E
G
J
E
G
F
K
G
J
J
Install Leg Connector Bracket
1.(SEE FIGURE 2) Place leg connector bracket (C) in center of table legs.
2.Attach leg connector bracket (C) to top left table leg using two long bolts (E)
 and metal washers (G).
3.Place one metal washer (G) onto each long bolt (E). Slide each bolt through table leg
 then leg connector bracket.
4.Secure leg connector bracket to table leg from inside of bracket, using two metal washers (G)
 and two hex nuts (F). Tighten leg bracket hardware using angle wrench (L) and hex wrench (M).
5.Repeat for remaining table legs.
Install Plastic Bolt Caps
1.(SEE FIGURE 2 and 3) Place one plastic bolt cap (J) on end of each short and long bolt (D, E).
Install Plastic Nut Caps
1.(SEE FIGURE 2) Locate hex nuts inside center of leg connector bracket (C).
 Place one plastic nut cap (K) onto each hex bolt.
2.Place table upright. Your table is now ready to use.
J
J
L
2
Detail A
Top Left Corner of Table
Table Leg Leg Connector
Bracket
Detail B
Bottom Right Corner of Table
Table
Leg
Leg Connector
Bracket