Astonica 50102705 User manual

Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
®
Model No: 50102705
Ilara 48” Round Dining Table
Instruction Manual
For warranty information, please refer to the back page of
this instruction manual.
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
NOTE: This product is intended for residential, non-commercial use.
Made in China
©2012 World Factory, Inc.
Distributed by:
World Factory, Inc.
Westlake, TX 76262
051112rev1
For Manuals, Replacement Parts or Customer Service visit:
www.ezreplacement.com
Limited Warranty
World Factory, Inc. Products for Home Use
World Factory, Inc. (Seller) warrants to the original Buyer only, that each Astonica Product will be free
from defects in material and workmanship for a period of one (1) year from date of purchase.
SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH
ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE SELLER
WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY FROM
REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER
MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This
warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to
normal use or weathering. To make a claim under this Limited Warranty, you must return the complete
product with proof of purchase, transportation prepaid, to any World Factory, Inc. authorized service
center. Call 1-888-422-7800 or visit: ezreplacement.com for the location of the nearest authorized
service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)
YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF
PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such
provision shall not affect any other provision herein, this Limited Warranty shall be construed as if
such invalid and/or unenforceable provision had never been contained herein.
This warranty gives you special legal rights, and you may also have other rights which vary from state
to state.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all
prior agreements, arrangements, or understandings between the parties relating to product warranty.

ASSEMBLY INSTRUCTIONS
A
A
C
C
Figure 1
Figure 2
Figure 3
PARTS & HARDWARE LIST
PART # DESCRIPTION QUANTITY
A Glass 1
B Table Rim 1
C Center Support 1
D Legs 4
E Bolts M6 x 25 8
F Bolts M6 x 15 8
G Washers 16
H Bolt Cover 16
I Hex Key 1
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
Parts Detail
1
NOTE: This product is intended for residential, non-commercial use.
2
B
B
B
D
D
E
F
FHGI
H
G
GE
H
1. (SEE FIGURE 1) Place the table rim (B) upside
down on a flat non-scratch surface then attach
legs (D) with bolts (F) and washers (G) using
hex key (I).
2. (SEE FIGURE 2) Insert the center support (C) in
between legs (D) and secure with bolts (E) and
washers (G) using hex key (I).
NOTE: Do not over tighten fasteners.
3. (SEE FIGURE 3) Turn table upright and carefully
set glass (A) into the table rim (B). Tighten
fasteners around the center support (C) in a
cross corner fashion to level the table and
secure for use. Apply bolt covers (H) to all
exposed bolts, refer to Figures 1 and 2.
D