Astonica 50105411 User manual

OUTDOORLIVING
MODEL NO: 50105411
Please keep this instruction manual for future reference
Casinella 42" Square Table
Instruction Manual
221004rev1
Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CONSUMER SUPPORT AT
1-888-424-3354
OR
IF YOU ARE A STORE MANAGER OR EMPLOYEE IN NEED OF ASSISTANCE CALL
1-888-851-5569
PLEASE HAVE YOUR STORE NUMBER READY
Limited Warranty
World Factory, Inc.®Products for Home Use
World Factory, Inc.®(Seller) warrants to the original Buyer only, that each Astonica™ Product will be
free from defects in material and workmanship for a period of one (1) year from date of purchase.
SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH
ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE
SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY
FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER
MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This
warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to
normal use or weathering. To make a claim under this Limited Warranty, you must return the complete
product with proof of purchase, transportation prepaid, to any World Factory, Inc.
®authorized service
center. Call 1-888-424-3354 for the location of the nearest authorized service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)
YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR
LOSS OF PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such
provision shall not affect any other provision herein, this Limited Warranty shall be construed as if
such invalid and/or unenforceable provision had never been contained herein.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all
prior agreements, arrangements, or understandings between the parties relating to product warranty.
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CUSTOMER SERVICE AT
1-888-424-3354
Made in China
©2004 World Factory, Inc.®
Distributed by:
World Factory, Inc.®
Southlake, TX 76092

ASSEMBLY INSTRUCTIONS
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER. CONTACT CUSTOMER SERVICE AT
1-888-424-3354.
A
BC
E
DG
FH I
FIGURE 1
PARTS & HARDWARE LIST
PART # DESCRIPTION QUANTITY
A 1Glass Table Top
B
C
1Connector Ring
D
4
Table Leg
E
12
Bolt, 6mm x 30
F
12
Plastic Umbrella Cap
Flat Washer
Plastic Bolt Caps
G
12
12
Allen® Wrench
H
Touch Up Paint (with table leg) 1
I
1
A
B
C
D
D
F
F
D
F
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
1. (SEE FIGURE 1) Unpack all parts and remove packing material on non-scratching surface.
2. Place table top (A) upside down on a flat, non-abrasive surface.
3. Attach each table leg (C) to edge of the table top (A) with bolt (D) and lock washer (F),
 finger tighten only.
4. Attach each leg (C) to connector ring (B) using bolt (D) and lock washer (F).
NOTE:Insert each bolt (D) from the inside of connector
  ring into table leg and finger tighten only.
5. Secure connector ring to table legs by tightening each bolt (D) two revolutions at a time,
 alternating between bolts in a cross corner fashion (X).
6. Once center connector ring is in position, tighten table top bolts (D) using Allen®wrench (G).
 Next, tighten connector ring bolts (D) using Allen®wrench (G).
7. Carefully turn the table frame assembly to the upright position onto it legs and
 securely tighten all bolts.
8. Place plastic bolt caps (H) over each bolt (D). Place plastic umbrella cap (E) over the
 umbrella hole in the table top (A).
Caution: Placing table top and legs on a hard surface may scratch
table glass and damage table rim and legs.