Astonica 50105348 User manual

IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CUSTOMER SERVICE AT
1-888-424-3354
Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CONSUMER SUPPORT AT
1-888-424-3354
OR
IF YOU ARE A STORE MANAGER OR EMPLOYEE IN NEED OF ASSISTANCE CALL
1-888-851-5569
PLEASE HAVE YOUR STORE NUMBER READY
Limited Warranty
World Factory, Inc.®Products for Home Use
World Factory, Inc.®(Seller) warrants to the original Buyer only, that each Astonica®Product will be
free from defects in material and workmanship for a period of one (1) year from date of purchase.
SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH
ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE
SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY
FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER
MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This
warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to
normal use or weathering. To make a claim under this Limited Warranty, you must return the complete
product with proof of purchase, transportation prepaid, to any World Factory, Inc.®authorized service
center. Call 1-888-424-3354 for the location of the nearest authorized service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)
YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR
LOSS OF PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such
provision shall not affect any other provision herein, this Limited Warranty shall be construed as if
such invalid and/or unenforceable provision had never been contained herein.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all
prior agreements, arrangements, or understandings between the parties relating to product warranty.
®
Made in China
©2005 World Factory, Inc.
Distributed by:
World Factory, Inc.
Coppell, TX 75019
Model No: 50105348
Kelly Resin Bistro Set
Instruction Manual
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
220205rev2
NOTE: This product is intended for residential, non-commercial use.
Maximum Load Capacity for chairs is 200 lbs.

PARTS & HARDWARE LIST
PART # DESCRIPTION QUANTITY
A 2Chair Back
B 2Chair Seat
C 8Chair leg
D
1
1
Table Top
Chair Center Brace
Table Center Brace
E
2
Table Leg
F3
Medium Nut (for chair)
G
11
Small Nut
H
16
Medium Nut (for table)
1
Plastic Spanner
I
J
L
6
Large Nut
K4
AB
C
D
E
F
G
H I J K
CAUTION: Do not over tighten fasteners.
C
B
A
K
A
B
I
D
C
C
F
D
H
Plastic
Studs
F
1.  (SEE FIGURE 1) Insert studs on chair
 back (A) through holes in chair seat (B).
2. With chair back (A) in place, insert
 studs of one chair leg (C) into chair
 seat (B), connecting the chair back,
 seat and leg.
3. Attach two medium nuts (I) and one
 large nut (K) using spanner tool (L).
4. Attach remaining legs, repeat step 2
 and step 3.
5. Assembly second chair in same manner,
 repeat steps 1 - 4.
6. (SEE FIGURE 2) Place threaded studs
 of chair brace (D) through the tab
 on chair leg (C).
7. Turn the chair upside down.
8. Fasten brace (D) using small nut (H).
 Use the spanner tool (L) to tighten
 nuts on all four legs. Do not to over
 tighten nuts.
9. (SEE FIGURE 3) Position table top (E)
 upside down on a clean surface.
10.Place the two holes at top of leg (F)
 over plastic threaded studs on bottom
 of table (E).
11.Secure using medium nuts (J). Use the
 plastic spanner (L) to tighten. Do not
 over tighten fasteners.
12.Position table right side up.
13.Place threaded studs of table center
 brace's (G) through tab on table leg (F).
14.Turn the table upside down and fasten
 brace (G) using small nuts (H). Tighten
 using spanner (L) on all four legs.
 Tighten all fasteners securely. Do not
 over tighten the fasteners.
Figure 1
Figure 2
Figure 3
L
E
KL
G
L
G
I
F
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER. CONTACT CUSTOMER SERVICE AT
1-888-424-3354.
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
NOTE: This product is intended for residential, non-commercial use.
Maximum Load Capacity for chairs is 200 lbs.
ASSEMBLY INSTRUCTIONS
12
I
L