Asus V1S Series User manual

Disassembly procedure
2 - 1
Disassembly Procedure
Please follow the information provided in this section to perform the complete
disassembly procedure of the notebook. Be sure to use proper tools described
before.
SUS V1S Series Notebook consists of various modules. This chapter describes the
procedures for the complete notebook disassembly. In addition, in between procedures,
the detailed disassembly procedure of individual modules will be provided for your service
needs.
The disassembly procedure consists of the following steps:
•Battery Module
•CPU Module
•Memory Module
•HDD Module
•Optical Drive Module
•Keyboard Module
•Top Case Module
•WLAN Module
•Motherboard Module
•LCD Module
Chapter
2
A

Disassembly procedure
2 - 2
Battery Module
The illustration below shows how to remove the battery module.
Remove battery module
1. Turn the notebook over. Unlock and hold the latch, and remove the battery.
CPU Module
The illustrations below show how to remove the CPU module from the notebook.
Removing CPU
1. Remove 5 screws (M2*5) and take the CPU door away.
BATTERY
1
2
3
M2*5
CPU MODULE
REMOVAL
CPU
REMOVAL

Disassembly procedure
2 - 3
Remove VGA board module
2. Remove 4 screws(M2*5)(M2*3),then remove the VGA board module
3. Remove the DIMM cover from the bottom case.
4. Remove 4 screws (M2*5) aside the CPU. And disconnect the CPU fan cable..
M2*5 M2*3
M2*5

Disassembly procedure
2 - 4
5. Remove the CPU thermal module from the bottom case.
6. Turn the non-removable screw here 180 degrees counter-clockwise to loosen the CPU.
7. Squeeze the vacuum handling pump and use it to lift the CPU away.

Disassembly procedure
2 - 5
Memory Module
The illustration shows how to remove the memory module form the notebook.
Removing Memory module
1. Pull two latches and pop the module up to a 45°angles, and then pulling out the module in that
angle.
HDD Module
The illustrations below show how to remove the HDD module from the notebook.
Removing HDD Module
1. Remove 1 screw (M2*5) here, open HDD door by the tweezers and then take away the HDD
door.
MEMORY
MODULE
MEMORY
REMOVAL
45o
HDD
MODULE
HDD
MODULE
REMOVAL

Disassembly procedure
2 - 6
2. Remove the HDD door from the bottom case and then put the HDD module.
3. Remove 4 screws (M3*3) to separate HDD from HDD housing

Disassembly procedure
2 - 7
Optical Drive Module
1. Unlock and hold the latch, and remove the ODD module.
Keyboard Module
The illustration of below shows how to remove the keyboard
Removing Keyboard
1. Remove 1 screw (M2*5) here, and then turn over the notebook.
2. Push the 4 latches in (F1, F6, F10, Ins) with a pair of tweezers or a single-slotted
screwdriver and lift the keyboard plate up.
KEYBOARD
OPTICAL
DRIVE
REMOVAL

Disassembly procedure
2 - 8
3. Lay the keyboard down over the Top case. *Do not remove the keyboard yet.
The keyboard cable is still attached.
4. Disconnect the FPC connector by a pair of tweezers.
Removing Keyboard Cable
1. Use a flexible connector tool to unlock the cable connector on both ends (no. 1).
2. Carefully pull out the keyboard cable (no. 2) with a pair of tweezers.
3. Lock the connector (no. 3) again to avoid possible breakage.
4. Remove keyboard from the top case.
1. Unlock
2. Cable out
3.
1. Unlock
3.

Disassembly procedure
2 - 9
Top Case Module
The illustrations below show how to disassemble and remove the top case module of the notebook.
The module contains the top case itself.
Removing Top Case Module
1. Use a pair of tweezers to remove both hinge Cover.
2. Use a pair of tweezers to disconnect both speaker cables.
TOP CASE
MODULE
TOP CASE
REMOVAL

Disassembly procedure
2 - 10
3. Disconnect the touchpad FPC and antenna.
4. Disconnect the LCD cable and inverter cable and switch board FFC.
inverter cable
LCD cable
Switch board cable
Touchpad FPC Antenna
Open the latch