AT&T TSD3600 User manual

Page 1 of 40
Oracle Ex. 1030
Page 1 of 40
Oracle Ex. 1030
Page 1 of 40
Oracle Ex. 1030

Page 2 of 40
TSD USERS MANUAL
Telephone ~ecurity Qevice
Model 3600
September 30, 1992

Page 3 of 40
Page ii
TSD User's Manual
Customer Assistance
For assistance with problems, or to order optional
accessories for the TSD, contact the AT&T Secure
Communications Products Customer Service Center at
the following telephone number.
AT&T Secure Communications Products
Customer Service Center
Toll Free Commercial
800-952-4082 919-279-7617
Have the following required information when calling the
AT&T Secure Communications Products Customer
Service Center.
AT&T Model
______ TSD
Serial Number: ---------------------
Purchase Date:
Purchased From:
----------
September 30, 1992

Page 4 of 40
TSD User's Manual Contents
TABLE OF CONTENTS
CHAPTER 1: Introduction . . . . . . . . . . . . . . . . . . . . . . • . . 1
Overview ..... IIi •• , ••• , • ~ " ... IJ .• , , II .... .-: • • • 1
Parts Checklist and Verification ........ , . . . . 2
Communication Interfaces . . . . . . . . . . 3
Power Interface . • . • . . . . . . . . . . . . . 3
CHAPTER 2: Installation . . . . . . . . . . . . . . . . . . . . . . . . • 5
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the Handset Module . . . . . . . 5
Installing the TSD . . . . . . . . . . . . . . . . 8
Removing the TSD . . . . . . . . . . • . . . . 10
CHAPTER
3: Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Operating the TSD . . . . . . . . . . . . . . . . . . . . . . 14
CHAPTER
4: Maintenance and
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 17
Maintenance . . . . . • . . . . . . . . . . . . . . . . . . . . . 17
Display Messages . . . . . . . . . . . . . . . . . . . . . . . 17
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . .
18
APPENDICES
Warranty Information . . . . . . . . . . . . . . . . . . . . .
21
Technical Specifications . . . . . . . . . . . . . . . . . . 25
FCC Rules, Part 15 and Part 68 . . . . . . . . . . . . 27
Optional Accessories . . . . . . . . . . . . . . . . . . . . . 29
September
30, 1992 Page iii

Page 5 of 40
Contents Tso· User's Manual
FIGURES
1-1: TSD and Accessories . . . . . . . . . . . . . . . . . . . . . 3
2-1: AT&T HandsetTypes
.........•........... 6
2-2: Handset Module Installation . . . . . . . . . . . . . . . . . 7
2-3: Equipment Installation
..................... 9
2-4: TSD Display Indicators . . . . . . . . . . . . . . . . . . . 11
TABLES
2-1: Handset Module to Handset Cross-Reference . . . . 6
2-2: Handset Module Installation Procedures . . . . . . . . 7
2-3: TSD Installation Procedures . . . . . . . . . . . . . . . . . 9
2-4: TSD Removal Procedures . . . . . . . . . . . . . . . . . 11
3-1 : Operating Procedures . . . . . . . . . . . . . . . . . . . . 14
4-1: TSD Display Messages . . . . . . . . . . . . . . . . . . . 17
4-2: Troubleshooting Procedures . . . . . . . . . . . . . . . .
19
Page iv September 30, 1992

Page 6 of 40
TSD User's Manual Contents
Every effort has been made to ensure that the
information in this book
is complete and accurate at the
time
of printing. However, this information is subject to
change.
SOFTWARE OWNERSHIP
AT&T provides the software included herein
(programmed into the TSD) for a one-time license fee
included in the price. The software remains the sole
property of AT&T
or its licensors and may not be
copied, duplicated, or used in otherthan the device in
which it was received.
EXPORT CONTROL
This product is subject
to U.S. Department of State
Export Regulations. Written U.S. Government approval
is required prior to export.
IMPORTANT SAFETY INSTRUCTIONS
Always follow these basic safety precautions when
using this product
to reduce risk of injury from fire or
electric shock.
1. Read Chapter 2 prior to installing the TSD.
Read and understand all instructions in this
manual before using this product.
2. Observe all warnings and instructions marked on
the product.
September 30, 1992 Page v

Page 7 of 40
Page vi
Contents TSD User's Manual
3. Unplug this product from wall outlets and
telephone jacks before cleaning. Clean exposed
parts with a soft, damp cloth.
Do not use aerosol
cleaners.
4. Do not use the product near water or when you
are wet If the product comes in contact with any
liquids, unplug the power cord immediately.
Do
not plug the product back in until it has been
dried thoroughly.
5. Install this product securely an a stable surface.
Damage may result
if the product falls.
6. Install this product in a protected location where
no one can step on or trip over power and line
cords.
Do not place objects on the cords that can
cause damage or abrasion.
7. The product is supplied with a power supply
designed for use with 110 VAC. If you are not
sure of the power supplied
to your location,
consult your local power company.
8. Do not allow anything to rest on the power cord.
Do not locate this product where the cord will be
abused by persons walking on it. Do not
overload wall outlets
as this can result in the risk
of fire or electric shock.
Do not staple or
otherwise attach
the AC power supply cord to
building surfaces.
September
30, 1992

Page 8 of 40
TSD User's Manual Contents
9. If this product does not operate normally; contact
the AT&T Secure Communications Products
Customer Service Center at the telephone
number listed
in the Customer Assistance
section of this manual. If the product is
damaged, refer
to the AT&T Warranty in the
back of this manual. Do
not open the device.
Opening the device may expose you
to
dangerous voltages or to other risks and may
void the warranty. Repairs must
be performed by
an
AT&T authorized technician.
1
o. Do not use the device in the vicinity of a gas
leak. If you suspect a gas leak, report it
immediately,
but use a telephone away from the
area where gas
is leaking.
September 30, 1992 Page
vii

Page 9 of 40
Contents
TSD User's Manual
Page viii September 30, 1992

Page 10 of 40
Introduction
Overview
Congratulations on the purchase of your new AT&T
Telephone Security Device (TSD), Model 3600. It has
been designed
to exacting AT&T standards for
convenient and reliable service. The TSD is a light-
weight device which provides an economical
way to
protect your most confidential telephone conversations.
It provides
tvvo-way voice compression and encryption
and
is compatible with most modular telephones.
The TSD is small and portable for use at home
or work
or for tucking into your briefcase when you travel. The
small size enables discrete use.
The voice compression algorithm used in the TSD
provides
s~perior voice quality.
For ease
of use, two pushbuttons control all the
operations involved in switching the unit between clear
and secure modes. (The display indicates
in which
mode
the unit is operating.) The TSD has different
customer-selectable Handset Modules
for operating with
the various types of telephone handsets. Only one
Handset Module
is supplied with the initial TSD.
September 30, 1992 Page 1

Page 11 of 40
Page 2
Chapter 1 TSD User's Manual
The TSD is a member
of the AT&T secure
communication products family. Its features include:
• Ease
of use
• Superior voice quality
• Compatibility with multiple telephone handsets
• Portability
• Simple installation.
Parts Checklist and Verification
Inspectpackage contents. Inspect the contents for
damage thatmay have occurred during transit. Save
all packing material until the Handset Module
is
installed and working properly.
One complete, basic TSD (as shown in Figure 1-1)
should include the following pieces.
• Telephone Security Device
• Handset Module
• TSD-to-Telephone Interface Cord
• 110-VAC Power Supply
• TSD Slip Cover (not shown)
Visually confirm that there are no broken parts and that
the TSD housing
and panel surfaces are free of obvious
defects. If you suspect any part is damaged, or parts
are missing. call
the AT&T Secure Communications
Products CustomerService Center.
Copy the serial number from
the bottom of the unit to
the front of this manual for warranty purposes.
September 30, 1992

Page 12 of 40
TSD User's Manual Chapter 1
POWER INTERFACE
POWER JACK (NOT SHOWN)
COMMUNICATION
INTERFACES
'- ~
1
HDIIJF JACK
'"'"'.......,.._ . JACK
~9~~
TSD-TO-TELEPHONE HANDSET MODULE
INTERFACE CORD
Figure 1-1 TSD and Accessories
Communication Interfaces
Physical implementation includes a TSD-to-Telephone
Interface Cord that interfaces the TSD and the
telephone being used.
Power Interface
An external, 110-VAC, plug-in, wall.-type power supply
furnishes power to the TSD.
September 30, 1992 Page 3

Page 13 of 40
Chapter 1
TSD User's Manual
Page 4 September 30, 1992

Page 14 of 40
Installation
Introduction
This chapter provides installation instructions for the
Handset Module and the TSD. Please read all
instructions carefully before you begin the installation.
Installing the Handset Module
To install the Handset Module, refer to Figures 2-1 and
2-2. Also refer
to Tables 2-1 and 2-2.
September
30, 1992 Page 5

Page 15 of 40
Page 6
Chapter 2 TSD User's Manual
-a" TYPE
•s• TYPE
Figure 2·1 AT&T Handset Types
Table 2·1 Handset Module
to Handset
Cross-Reference
HANDSET TYPE
HANDSET MODULE
AT&TG HM-3
AT&T K
HM-2 or HM-3
AT&T R HM-1
AT&T S HM-2
All non-AT&T See Note
NOTE: For specific AT&T "K" type handsets and all non-AT& T telephones,
call the AT&T Secure Communications Products CustomarSarvica Canter at
1-800-952-4082 or 1-919-279-7617 for initial assistance in selecting Handset
Modules. if needed.
September 30, 1992

Page 16 of 40
TSD User·s Manual
HANDSET
MODULE
-
; -AT&T
<::;::"
I!I
....
=nJ.v~y
lllllllllliiii:J;
"'-
3600
~~~
I
Figure 2-2 Handset Module Installation
Chapter 2
ARROW
Table 2·2 Handset Module Installation Procedures
STEP ACTION
1
Follow these steps to install the Handset Module.
CAUTION
Always unplug the Power Supply before installing a
new Handset Module.
September 30. 1992 Page 7

Page 17 of 40
Page 8
Chapter 2 TSD User's Manual
STEP ACTION
2 Refer to Figure 2~1 to identify the type of handset to
be used with the TSD. If your telephone is not an
AT&T telephone, call the AT&T Secure
Communications Products Customer Service Center to
exchange or purchase the correct module. Different
Handset Modules may be required for use of this
device with other telephones.
NOTE: lf you did not specify the Handset Module on
your purchase order, a type HM-1 Handset Module
was included as the default Module. Any other
handset type requires the exchange of the type HM-1
Module for the proper Handset Module.
3 Refer to Table 2-1 to cross-reference the correct
Handset Module to your AT&T handsettype.
4 Grasp the, rear of the Handset Module, and turn it so
that the arrow is on top and points forward. Refer to
Figure 2·2.
5 CAUTION
Improper Handset Module insertion can cause pin
damage. Use caution when installing a module into
the TSD.
Carefully insert the Handset Module into the rear of
the TSD until the module is completely engaged.
Installing the TSD
To install the TSD, follow the steps in Table 2-3. Also
refer to Figures 2-3
and 2-4.
September
30, 1992

Page 18 of 40
TSD User's Manual
Chapter 2
HANDSET
JACK
POWER
PHONE JACK
JACK
HANDSET
TSD*TO~TELEPHONE
INTERFACE CORD
WITH CORD HANDSET
FROM YOUR MODULE
TELEPHONE
Figure 2·3 Equipment Installation
Table
2-3 TSD Installation Procedures
STEP ACTION
1 Verify that the Handset Module is inserted, and place
the TSD on a desk top or other suitable surface.
NOTE: The device should not be exposed to heat
(over 100° F) or cold (under 40° F) while ih operation.
It should be protected from water and extended
exposure to sunlight.
September 30, 1992 Page 9

Page 19 of 40
Chapter 2
TSD User's Manual
STEP ACTION
2 Follow these steps to install the TSD with a telephone.
CAUTION
Exercise care when disconnecting and connecting
cables so as not to damage the connectors.
Disconnect the modular plug of the handset from the
handsetjack on the telephone. Do not disconnect the
modular plug from the LINE jack
on the telephone.
3 Connect the modular plug of the handset into the
HANDSET jack on the TSD.
4 Plug one end of the
TSD~to-Telephone Interface Cord
into the PHONE jack on the TSD and the other end of
the cord into the telephone (where you unplugged the
handset).
5 Plug the Power Supply into the POWER jack on the
rear of the TSD, and plug the Power Supply into
an
AC outlet. The TSD will run a self test.
When first plugged in, both the SECURE and CLEAR
icons,
as well as all segments of the 4-character
hexadecimals, should be illuminated on the TSD
display. They will remain illuminated until the unit has
completed its self tests (approximately 3 seconds).
The unit is ready to use when only the CLEAR icon is
displayed. (Refer to Figure 2-4.)
Removing the TSD
To remove the TSD, follow the steps in Table 2-4.
Page 10 September 30, 1992

Page 20 of 40
TSD User's Manual Chapter 2
CLEAR AND CUAA
SECURE- .lrf:.. 888811 c::::=>
ICONS TT4: ,I c::::=>
Figure 2·4 TSD Display Indicators
Table 2·4 TSD Removal Procedures
STEP ACTION
1
Unplug the Power Supply from the AC outlet, and
disconnect the Power Supply cord from the
POWER jack on the rear of the TSD.
2
Disconnect the TSD~to~Telephone Interface Cord
from the handset jack on the telephone and the
PHONE jack on the TSD.
3 Disconnect the modular plug of the handset from
the HANDSET jack on the TSD, and connect it into
the handsetjack on the telephone.
4
Grasp the Handset Module, and pull it away from
(Optional)
the TSD.
5 Place the TSD and its accessories in a safe
location.
September 30, 1992 Page
11