AT&T PWS02 User manual

User’s Manual
Hot Joe II
PWS02
Portable Bluetooth® Speaker

Page 2
Welcome |Thank you for buying AT&T Hot Joe II
Introduction
Features
- Bluetooth 2.1 + A2DP, AVRCP
- Hands-free speakerphone
- Wireless range of up to 30 feet
- Stereo speakers with RealBass technology
- Easy USB charging
- Rechargeable Lithium Battery
- 3.5 mm auxilary input jack

Page 3
What’s Included
Unpack the Hot Joe II and make sure all accessories are put
aside so they will not be lost.
Micro USB Cable
Portable Speaker

Page 4
Content
Introduction
Features 2
What’s Included 3
Safety Information
Important Safety Instructions 5
Getting Started
Location of Main Unit Controls 6
Operational Instructions
Charging the Unit 7
Power ON/OFF 7
AUX Input 7
Pairing Your Bluetooth Device 8
Music Playback Functions 8
Hands-free Speakerphone 9
Troubleshooting 10
Compliance with FCC Regulations 11
Warranty Information
Limited Warranty 12
Specications 14

Page 5
Please read all safety and operating instructions carefully
before installation and use, and keep these instructions handy
for future reference. Take special note of all warnings listed in
this user’s manual and on the Hot Joe II.
1. Attachments - Do not use attachments that are not
recommended by the manufacturer.
2. Water and Moisture - The unit should not be used near water.
For example: near a bathtub, washbowl, kitchen sink, laundry tub,
swimming pool or in a wet basement.
3. Ventilation - The unit should be situated so that its location or
position does not interfere with its proper ventilation. For example,
it should not be situated on a bed, sofa, rug or similar surface that
may block ventilation openings. Also, it should not be placed in
a built-in installation, such as a bookcase or cabinet, which may
impede the flow of air through the ventilation openings.
4. Objects and Liquid Entry - Care should be taken so that external
objects do not fall into and liquids are not spilled onto any openings
or vents located on the product.
5. Power Source - The unit should be connected only to a power
supply of the type described in the operating instructions or as
marked on the unit. If you are not sure, please consult the dealer
or local power company.
6. Heat - The unit should be situated away from heat sources such
as radiators, heat registers, stoves or other appliances (including
amplifiers) that produce heat.
7. Servicing - The user should not attempt to service the unit
beyond those methods described in the user’s manual. Opening or
removing covers will expose you to dangerous voltage and other
hazards. Service methods not covered in the user’s manual should
be referred to qualified service personnel.
Safety Information
Important Safety Instructions

Page 6
Getting Started
Location of Main Unit Controls
1. LED indicators
2. Hands-free /
Power button
3. Volume - /
Volume +
4. Previous song /
Next song
5. Power ON/OFF
switch
6. 3.5 mm AUX
input
7. Micro USB port
for charging

Page 7
Operational Instructions
Charging the Unit
1. Charge your unit through any Micro USB Jack or wall charger.
2. The LED indicator will turn red while charging.
3. Once the battery is fully charged the red indicator will turn
off.
Note: Please charge the battery up to 4 hours before initial use.
Power ON/OFF
1. Slide the switch on the back of the speaker to the ON
position.
2. Press and hold the power button until you hear a sound
indicating the unit is ON and in Bluetooth pairing mode. The
LED indicator will turn blue and will be blinking.
3. To power down your speaker, slide the switch on the back
of the unit to the OFF position.
AUX Input
1. To Playback your music via the AUX IN port, plug a standard
stereo headphone cable (3.5mm, not included) from your
audio device to Hot Joe II and begin playback on your audio
device.
2. To increase or decrease the volume, press VOL + and VOL –
buttons.
Note:
- The Skip/Hands-free button does not work with external devices.
- The AUX input source will be automatically selected when the auxiliary cable is connected.
- Once the auxiliary cable is disconnected, the unit will switch back to Bluetooth mode.

Page 8
Operational Instructions
Pairing Your Bluetooth Device
1. Turn the unit on. The Hot Joe II will beep and the indicator
will turn blue and flash indicating the unit is in pairing
mode.
2. Navigate to the Bluetooth menu on your device and begin
searching for the available devices.
3. Select PWS02 from the list of results, and your device will
begin to pair. If the unit asks for a code, please enter
“0000”.
4. Once connected,the speaker will beep and the blue
indicator will stop flashing.
Music Playback Functions
-Press the Power button to Play and Pause the music.
-Press the Skip Buttons to skip to Next or Previous Song.
-Press the Vol+ or Vol - buttons to increase or decrease the
volume.
-Press and hold the Power button to turn the unit to Standby
mode.

Page 9
Operational Instructions
Hands-free Speakerphone
Placing a Call
-To place a call,initiate the call from your Bluetooth
connected phone and the call will automatically be routed
through your paired Hot Joe II and the music will be
stopped.
-When the call is terminated, the current music will be
resumed. The call can also be terminated by pressing the
hands-free button.
Receiving a Call
-Press the Hands-free button to answer the call on your
speaker.
-Press and hold the Hands-free button to reject the call.
-To disconnect,press the Hands-free button again.

Page 10
Troubleshooting
Symptom Solution
No power -Recharge the battery.
-Move the power switch to the
ON position.
No sound -Raise the volume by pressing
the VOL + button.
-Make sure your device is
connected to the speaker and
playing music.
-Raise the volume level of the
connected device.
-Set input source as AUX IN or
Bluetooth mode.
Hands-free not working -Set to Bluetooth mode (Hands-
free function is only available in
Bluetooth mode)

Page 11
Compliance with FCC Regulations
Caution!
The user is cautioned that changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
The equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate Radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to Radio
communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to Radio or television
reception, which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit dierent from which the receiver
is connected.
-Consult the dealer or an experienced Radio/television technician for assistance.
This equipment complies with FCC’s RF radiation exposure limits set forth for an
uncontrolled environment. The antenna(s) used for this transmitter must be installed
and operated to provide a separation distance of at least 20 cm from all persons
and must not be collocated or operating in conjunction with any other antenna or
transmitter. Installers must ensure that 20 cm separation distance will be maintained
between the device (excluding its handset) and users.
THE SPECIFICATION AND EXTERNAL APPEARANCE OF THE HEADPHONES ARE
SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.
If at any time in the future you should need to dispose of this
product, please note that waste electrical products should not
be disposed of with household waste. Please recycle where
facilities exist. Check with your local authority or retailer for
recycling advice.

Page 12
Warranty Information
Limited Warranty
The AT&T brands are used under license. Any repair, replacement, or
warranty service, and all questions about this product should be directed to
Concept 101 LLC at www.att.com/electronics or call 1 [phone] from
the USA or Canada.
Concept 101 LLC warrants to the original purchaser that the product will be free from defects
in material, parts and workmanship for the period designated for this product. The warranty
commences the day the product is purchased and covers up to a period of one (1) year.
Concept 101 LLC agrees that it will, at its option, replace the defective product with either a
new or remanufactured headset equivalent to your original purchase during the warranty
period. Should the Parts warranty period exceed the Labor warranty period, Concept 101 LLC
will supply at no charge for the remainder of the Parts warranty, any new or remanufactured
replacement parts as required by the product. During this period all labor and service charges
will become the responsibility of the customer.
Exclusions: This warranty does not apply to the appearance or exterior of the product
which may have been damaged or defaced, altered or modied in design or
construction. This warranty does not apply if the serial number is altered or
removed, or if there is any damage due to power line surge, user damage to
the AC power cord, connection to improper voltage source, general misuse,
accidents, or repair attempts by unauthorized service agents. Other exclusions
include ear pads, rechargeable and non-rechargeable batteries.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE
EXCLUSIVE REMEDY OF THE CUSTOMER; Concept 101 LLC SHALL NOT BE
LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH
OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT, EXCEPT TO
THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY
OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE ON THIS
PRODUCT IS LIMITED TO THE DURATION OF THE WARRANTY.
Some states do not allow the exclusion or limitations of incidental or
consequential damages, or limitations on how long the warranty lasts. In
these cases the above exclusions or limitations may not apply to you. This
warranty gives you specic legal rights and you may also have other rights
which vary from state to state.

Page 13
Warranty Information
Obtaining Service: To obtain service, product literature, supplies or accessories please call
1 888-920-8680, or visit our website, www.att.com/electronics, to create
a ticket for exchange/repair. Please make sure to provide the date of
purchase, model number and a brief description of the problem. Our
customer service representative will contact you or send detailed return
instructions.
Concept 101 LLC does not warrant that the unit will work properly in all environmental
conditions, and makes no warranty and representation, either implied or expressed, with
respect to the quality, performance, merchantability, or tness for a particular purpose
other than the purpose identied within this user’s manual. Concept 101 LLC has made
every eort to ensure that this user’s manual is accurate and disclaims liability for any
inaccuracies or omissions that may have occurred. Information in this user’s manual is
subject to change without notice and does not represent a commitment on the part of
Concept 101 LLC. Concept 101 LLC reserves the right to make improvements to this user’s
manual and/or to the products described in this user’s manual at any time without notice.
If you nd information in this manual that is incorrect, misleading, or incomplete, please
contact us through our website.

Page 14
Specications
-Bluetooth 2.1
-Bluetooth compatibility: Bluetooth 2.0 or above device with
A2DP/AVRCP
-Playing time: Up to 4 hours
-Charging time: 3 to 4 hours
-Impedance: 4 Ω
-Working distance: Up to 30 
* Up to 30 . wireless range as determined by Bluetooth SIG. Range may vary depending on
the line of sight obstacles.

www.att.com/electronics
© 2017 Concept 101 LLC. All Rights Reserved. AT&T and the AT&T logo are trademarks
of AT&T Intellectual Property licensed to Concept 101 LLC, New York, New York
10018. D Issue 3.1AT&T 9/2017.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth
SIG, Inc. Other trademarks and trade names are those of their respective owners.