ATCOM IPPBX IP02 User manual

Figure: ATCOM IPPBX IP02
ATCOM®IPPBX IP02
Product Guide
Version: 1.0
2010-05-10

www.atcom.cn 1
Content
CONTACT ATCOM ...............................................................................................................................3
CHAPTER 1 THE INTRODUCTION OF IP02............................................................................................4
CHAPTER 2 ACCESS TO THE IP02.........................................................................................................6
2.1 WEB PAGE ACCESS BY BROWSER ............................................................................................................6
2.2 SSH ACCESS BY PUTTY..........................................................................................................................7
2.3 ACCESS BY BROWSER WITH FALLBACK IP ADDRESS .....................................................................................8
2.4 CONSOLE PORT ACCESS TO IP02 ............................................................................................................8
CHAPTER 3 CONFIGURE IP02 BY WEB GUI ........................................................................................ 10
3.1 SYSTEM STATUS .................................................................................................................................10
3.2 CONFIGURE HARDWARE......................................................................................................................10
3.3 TRUNKS ...........................................................................................................................................10
3.3.1 Create Analog Trunks ............................................................................................................11
3.3.2 VoIP Trunks ............................................................................................................................11
3.4 OUTGOING CALLING RULES .................................................................................................................12
3.5 DIAL PLANS ......................................................................................................................................13
3.6 USERS .............................................................................................................................................14
3.6.1 Create SIP/IAX User ...............................................................................................................14
3.6.2 Create Analog User................................................................................................................15
3.7 RING GROUPS...................................................................................................................................17
3.8 CALL QUEUES ...................................................................................................................................18
3.9 VOICE MENUS ..................................................................................................................................19
3.10 TIME INTERVALS ..............................................................................................................................20
3.11 INCOMING CALLING RULES ................................................................................................................21
3.12 VOICEMAIL.....................................................................................................................................22
3.13 CONFERENCING...............................................................................................................................24
3.14 FOLLOW ME...................................................................................................................................25
3.15 VOICEMAIL GROUPS ........................................................................................................................ 27
3.16 VOICE MENU PROMPTS.................................................................................................................... 27
3.17 SYSTEM INFO ..................................................................................................................................29
3.18 BACKUP .........................................................................................................................................31
3.19 ACTIVE CHANNELS ...........................................................................................................................32
3.20 OPTIONS........................................................................................................................................33
3.21 ASTERISK LOGS................................................................................................................................35
3.22 BULK ADD......................................................................................................................................36
3.23 FILE EDITOR.................................................................................................................................... 37
3.24 ASTERISK CLI..................................................................................................................................38
3.25 NETWORK SETTINGS ........................................................................................................................38
3.26 FIRMWARE UPDATE..........................................................................................................................39
3.26.1 Download the Latest Firmware File and Set up TFTP Server. ..............................................39

www.atcom.cn 2
3.26.2 Update for IP02 from Web Page..........................................................................................40
3.27 CALL DETAIL RECORDS ......................................................................................................................40
CHAPTER 4 AN APPLICATION CASE OF IP02 ...................................................................................... 42
4.1 HOW TO MAKE INTERNAL CALLS THROUGH IP02.....................................................................................43
4.1.1 Access to the Web Page of IP02 by Browser..........................................................................43
4.1.2 Add up Users from Web Page of IP02....................................................................................43
4.1.3 Register a SIP user 6001 in AT610 .........................................................................................45
4.2 HOW TO MAKE A CALL TO 0UTSIDE THROUGH PSTN................................................................................46
4.2.1 Create an Analog Trunk .........................................................................................................46
4.2.2 Create an Outgoing Calling Rule ...........................................................................................46
4.2.3 Create a Dial Plan .................................................................................................................. 47
4.2.4 Create a User.........................................................................................................................47
4.3 HOW TO GET AN INCOMING CALL FROM OUTSIDE ....................................................................................48
4.3.1 Create an Analog Trunk .........................................................................................................48
4.3.2 Create an Incoming Calling Rule............................................................................................48
4.3.3 Create a Voice Menu .............................................................................................................48
4.4 HOW TO CALL EACH OTHER DIRECTLY FROM DIFFERENT NETWORK SEGMENT. ..............................................49
4.5 HOW TO CALL THROUGH VOIP TRUNK...................................................................................................52
4.5.1 Call from IP02 to IP08............................................................................................................52
4.5.2 Call from IP08 to IP02............................................................................................................55
4.6 HOW TO TRANSFER FILES BETWEEN WINDOWS PC AND IP02 ....................................................................57
CHAPTER 5 REFERENCE .................................................................................................................... 59

www.atcom.cn 3
Contact ATCOM
The Introduction of ATCOM
Founded in 1998, ATCOM technology has been always endeavoring in the R&D and
manufacturing of the internet communication terminals. The product line of ATCOM includes IP
Phone, USB Phone, IP PBX, VoIP gateway and Asterisk Card.
Contact Sales:
Address
A2F , Block 3 ,Huangguan Technology Park , #21 Tairan 9th Rd, Chegongmiao ,
Futian District , Shenzhen China
Tel
+(86)755-23487618
Fax
+(86)755-23485319
E-mail
[e-mail]
Contact Technical Support:
Tel
+(86)755-23481119
E-mail
[e-mail]
Website Address: http://www.atcom.cn/
ATCOM Wiki Website:http://www.openippbx.org/index.php?title=Main_Page
Download Center: http://www.atcom.cn/download.html

www.atcom.cn 4
Chapter 1 the Introduction of IP02
Overview of the IP02
The IP02 is a complete Asterisk Appliance with one dual port FXO or FXS module. It is an
embedded open source Linux system with built-in SIP/IAX2 proxy server and NAT features. It
provides a solid, uniform platform for traditional PSTN communications as well as VoIP
communications.
Targeting for SOHO user and SMB market with an easy to use graphical interface, IP02 provides a
cost-saving solution on their telecommunication/data needs. With IP02, company with branch
offices in different countries can be easily combined together to work like a virtual single office
through Internet.
Features
Open Source Asterisk IP PBX
High performance OSLEC (Open Source Line Echo Canceller)
Configurable IVR menu
Voice Mail, Voicemail to Email
Call forward, Call waiting, Call transfer
Call conference
Call queues, Ring group
SIP trunk, IAX trunk, PSTN analog trunk
Call Detail Record
Access via: SSH/telnet/web
Firmware upgradable via web page
50+ available SIP/IAX2 extensions
20 concurrent calls
Applications
SOHO/SMB telephony system
Hosted service
FAX terminal
IVR system
Interface
1 * RJ45 port
1 * Power port
2* RJ11 port (FXS/FXO interchangeable)
1* Dual port FXO/FXS module slot
Hardware
CPU: 400MHz Blackfin 532 Chip
Two analog (FXO/FXS) module interface

www.atcom.cn 5
NAND flash 256 MB
SDRAM 64MB
System
Open Source uClinux
Measurement and Weight
Inner box
100 * 100 * 28mm
G.W./unit
0.36KG
Carton MEAS
456 * 442 * 362 mm
Units per Carton
40 units/ CTN
G.W./CTN
17 KG/CTN
Package
Item
Quantity
IP02
1
RS232 module
1
Power Adapter
1
Manual (disk)
1
For the usage of IP02 in VoIP field, you can refer to the following network topology.

www.atcom.cn 6
Chapter 2 Access to the IP02
You need a PC to access to the IP02, there are four ways for you to access the IP02:
1. Web page access by browser
2. SSH access by putty
3. Access by browser with Fallback IPAddress
4. Console port access by RS232 console cable
In order to access to IP02 by the first three ways, you have to check that if your network
connection between IP02 and PC is OK. If you do not have network connection between IP02 and
PC, you can try to use the last way to access to IP02 and change the IP address for IP02.
2.1 Web Page Access by Browser
It is the most convenient and common way to access the IP02, you just need to open your browser
and input the IP address of IP02 WAN port (the default IP address is 192.168.1.100). You would
better use Firefox instead of IE, because there are compatible issues.
Then input the default Username: admin; Password: atcom (the password of old version is
mysecret) in the presented screen like the following:
When you login successfully, you can get the configuration web page as below:

www.atcom.cn 7
2.2 SSH Access by Putty
Logging into IP02 by SSH, you can configure IP02 by Linux command.
1) Please open your putty software, and input the IP02 IP address in the Host Name textbox,
input port number in the Port textbox, click the SSH Connection type, then click open button.
Please refer to the following screen:
2) Please input username: root, and the default password: 12xerXes16 in the following screen,
you can access to IP02 successfully.

www.atcom.cn 8
When you log into IP02 successfully, you can get the following illustration:
2.3 Access by Browser with Fallback IP Address
This way only be supported by the latest version (voiptel_ce_IP02_08-0.3.6) of IP02. If you forget
the IP Address of IP02 you have set up, you can use the fallback IP Address: 172.31.255.254/30.
Before logging into IP02, please set up the IP Address of your PC: 172.31.255.253 and SubMask:
255.255.255.252. At last, you can open your browser and enter:172.31.255.254 to log into the web
page of IP02.
2.4 Console Port Access to IP02
If you do not have network connection between IP02 and PC, you can try to access to IP02 by
console port. Please try to do as the following steps:
1. Please connect the console port of IP02 to your PC’s console port with RS232 console cable,
you can refer to the following illustration:

www.atcom.cn 9
2. Please run your Hyper Terminal, and set up the console port like the following:
Bits per second: 115200
Data bits : 8
Parity: None
Stop bits: 1
Flow control: None
3. Change the IPAddress by Hyper Terminal
The default IP address of IP02 is 192.168.1.100. Your network may have a different IP address
range such as 192.168.10.xx. In this situation, you can not access to IP02 by putty and browser if
you do not change the IP02 IP address. So you have to change the IP address for IP02 by Hyper
Terminal to make it in the same network segment as your LAN.
After you have accessed to IP02 by Hyper Terminal, please use the following command to change
the IP address for IP02.
root:~> ifconfig eth0 192.168.1.151(the IPaddress you want to set for IP02)
By this way, the IP address you set for IP02 is temporary, it will recover to the original default IP
address after rebooting. If you want to give a static and permanent IP address for IP02, you can try
to set it in web GUI, for detail steps please refer to chapter 3.

www.atcom.cn 10
Chapter 3 Configure IP02 by Web GUI
3.1 System Status
In the system status screen, it displays the functions you configured, such as: trunks, extensions,
conference and so on like the following screen:
3.2 Configure Hardware
In the configure hardware page, it includes the following components: analog hardware, tone
region, advanced settings.
Analog Hardware
When you boot the IP02, which will detect the FXO and FXS modules automatically, the analog
hardware component displays the modules which are detected correctly.
Tone Region
You should select the tone region according to your country, if it does not have your country’s
name in the dropdown list, please ask your service operator which kind of tone region is used in
your area.
3.3 Trunks
To receive calls from PSTN and make calls to the outside world, you have to use trunk. Please
select the Trunks option from the vertical menu on the left of the main page, then you can get the
following screen:

www.atcom.cn 11
3.3.1 Create Analog Trunks
Analog trunk is associated with FXO port, and it will call outside by PSTN line. Click on New
Analog Trunk in the illustration above, the pop-up screen is where you create and set up trunk.
There are many parameters for you to set up, I just set the following two parameters:
Channels: select the FXO port you want to use. Here I use the port 2.
Trunk Name: a unique label to help you identify the trunk when listed in outgoing calling rules
and incoming calling rules. Here I use the trunk1 as my trunk name.
For the advanced options, you can put your cursor on the label, you can get the information
of the parameter, customers have to set these parameters according to your service provider and
your need.
3.3.2 VoIPTrunks
A VoIP service provider (VSP) that you have signed up with is also a trunk. Via the VoIP trunk you
can dial via the VoIP service to reduce your cost when making international calls. You can set up

www.atcom.cn 12
the VoIP trunk to make calls to the PSTN or other VoIP network depends on the service you use.
You can also use the VoIP trunk to link headquarter and branch offices for free internal calls.
Click on New SIP/IAX Trunk, the following screen is where you create and set up VoIP trunk:
The important parameters are:
Type: You can select SIP or IAX type to meet your need.
Provide Name: a unique label to help you identify the trunk when listed in outgoing calling rules
and incoming calling rules.
Hostname: the IP address or domain name of your service provider’s server.
Username: the username that your service provider configured.
Password: the password that your service provider configured for the user.
3.4 Outgoing Calling Rules
Outgoing calling rules is used to route an outgoing call, when you make an external call, which
trunk and what dial-pattern the call used are configured in outgoing calling rules. Please select the
Outgoing Calling Rules option from the vertical menu on the left of the main page, then you can
get the following screen:
Click on New Calling Rule button on the illustration above, the following screen is where you
create and set up outgoing calling rule:

www.atcom.cn 13
The important parameters I configured are below:
Calling Rule Name: a unique label to help you identify the outgoing calling rule when listed in
dial plans, I use outgoing1 as the calling rule name here.
Pattern: it acts like a filter for marching numbers you dialed, here I set up _2X., it means any
number you dial out with prefix 2 will use this outgoing call rule.
Use Trunk: select the trunk for outgoing calling rule, here I select the trunk1 I set up before.
Strip: I press 1 here, it will strip the first digit of the number string you dialed.
You can get the detail information about every single parameter by putting your cursor on the
label.
At last, please click on Save button, and click on Apply Changes button in up right corner of the
main page.
The way of outgoing calling rules works:
Every time you dial a number, asterisk will do the following in strict order:
•Examine the number you dialed.
•Compare the number with the pattern that you have defined in your first outgoing rule and if
matches, it will initiate the call using that trunk. If it does not match, it will compare the
number with the pattern that you have defined in the second outgoing rule and so on.
•Pass the number to the appropriate trunk to make the call.
3.5 Dial Plans
A DialPlan is a set of Calling Rules that can be assigned to one or more users. Please select the

www.atcom.cn 14
Dial Plans option from the vertical menu on the left of the main page, then you can get the
following screen:
Click on New DialPlan button on the illustration above, the following screen is where you create
and set up dial plan:
DialPlan Name: a unique label to help you identify the dial plan when listed in user component,
you have to set up a dial plan name and select outgoing call rule and local context that you want to
use.
3.6 Users
Users component is used to add or remove Analog, SIP, IAX extension. Please select the Users
option from the vertical menu on the left, then you can get the following screen:
3.6.1 Create SIP/IAX User
Click on Create New User button on the illustration above, the following screen is where you
create and set up user:

www.atcom.cn 15
In General component, you have to set up Extension, CallerID, Name, OutBound CallerID
parameters, and choose a DialPlan for the extensions. Here I set up user 6001, and select
DialPlan1 for the user.
I select Enable Voicemail for this User option, so the user has voicemail function.
In the Technology component, you have to select SIP or IAX. Here I want to configure a SIP user,
so I select SIP. For the Codec Preference, only the first two types of code you set are available.
In the Other Options component, I select Is Agent which will be listed in Call Queues as a
selectable member for call queue.
At last, please click on Update button, and click on Apply Changes button in up right corner of
the main page.
3.6.2 Create Analog User
Click on Create New User button, the following screen is where you create and set up user:

www.atcom.cn 16
In the General component, you have to setup Extension, CallerID, Name, OutBound CallerID
parameters, and choose a dialplan for the phone. Here I set up user 6002, and select DialPlan1 for
the user.
I select Enable Voicemail for this User option, so the user has voicemail function.
In the Technology componet, you have to select the port in which the analog phone will be
plugged from the drop-down list of Analog Station. I select Enable Voicemail for this User
option, so the user have voicemail function.
In the Other Options component, I select Is Agent which will be listed in Call Queues as a
selectable member for call queue.
At last, please click on Update button, and click on Apply Changes button in up right corner of
the main page.
Attension: in the textbox of Extension, the value you set is limited to a range, you can adjust the
range in the following screen to meet your requirement. Please select the Options option from the
vertical menu on the left, then you can get the following screen:

www.atcom.cn 17
3.7 Ring Groups
Define Ring groups to dial more than one extension simultaneously, or to ring more than one
phone sequentially. This feature may also be called Hunt groups.
Please select the Ring Groups option from the vertical menu on the left of the main page, then
you can get the following screen:
Click on New RingGroup button on the illustration above, the following screen is where you
create and set up ring group:

www.atcom.cn 18
Set the ring group name and extension for the ring group, select ring group members from
available users.
Select strategy for ring group:
Ring in Order: when someone calls the ring group, the ring group member will ring in order.
Ring all simultaneously: when someone calls the ring group, all of the ring group member will
ring at the same time.
If not answered Goto: choose a destination from the drop-down list, when no one in the ring
group answers the call.
At last, please click on Update button, and click on Apply Changes button in up right corner of
the main page.
3.8 Call Queues
Please select the Call Queues option from the vertical menu on the left of the main page, then you
can get the following screen:
Click on Create New Queue button on the illustration above, the following screen is where you

www.atcom.cn 19
create and set up call queue:
Extension: a unique label to help you identify the call queue when listed in outgoing calling rules
component.
Agents: select the users which you want them to be queue member.
You can get information of other parameters by putting your mouse on the label.
At last, please click on Update button, and click on Apply Changes button in up right corner of
the main page.
3.9 Voice Menus
Like most organization, we would like to redirect all of the incoming calls automatically. The
voice menu is very handy for these sorts of things. The system should allow callers to make the
selection according to the voice menu.
Please select the Voice Menus option from the vertical menu on the left, then you can get the
following screen: