ATD Tools ATD-7429 User manual

ATD-7429
1000 lbs. Economy Hydraulic Telescopic Transmission Jack
Owner’s Manual
Features: Specifications:
47.36"
79.54"
9.84"x9.84"
9.96"x9.96"
13.58"x13.78"
79.2
ATD7429_rev_0323
Made in China to ATD Tools, Inc. Specifications
Visit us at www.atdtools.com

2
SPECIFICATIONS
47.36" 79.54" 9.84"x9.84" 9.96"x9.96" 13.58"x13.78"
Saddle
Tilt
Caster
Carrying Handle
Release V
(not shown)
ATD-7429 1,000 lbs.
SAFETY and GENERAL INFORMATION
Save these instructions. For your safety, read, understand, and follow the information provided with and on this jack
before using. The owner and operator of this equipment should have an understanding of this jack and safe operating
procedures before attempting to use. The owner and operator should be aware that use and repair of this product
may require special skills and knowledge. Instructions and safety information should be conveyed in the operator's
native language before use of this jack is authorized. If any doubt exists as to the safe and proper use of this jack,
remove from service immediately.
Inspect before each use. Do not use if broken, bent, cracked or damaged parts are noted. Any jack that appears
damaged in any way, or operates abnormally should be removed from service immediately. If the jack has been or
suspected to have been subjected to a shock load (a load dropped suddenly, unexpectedly upon it), immediately
discontinue use until jack has been checked by a factory authorized service center (contact distributor or manufacturer
for list of authorized service centers). It is recommended that an annual inspection be done by personnel.
Labels and operator's manuals are available from manufacturer.
PRODUCT DESCRIPTION
This Hydraulic Transmission Jack is designed to be used as an aid in the removal and installation of automotive and
light truck transmissions, transfer cases and transaxles. This jack is for use under a properly secured, overhead lift
or a garage pit.
Capacity
Model
Minimum
Height
Maximum
Height
Saddle
Base
Saddle
Area (Min)
Saddle
Area (Max)
Figure 1 - ATD-7429 nomenclature

Before Use
1. V
2. this product, read the operator's manual and familiarize with the
.T
a. Close the release valve by turning it clockwise until it stops.
Open the release valve by turning it two full rotations counterclockwise from its closed position.
This is the ‘CLOSED’ release valve position used
to raise the saddle.
. This is the
‘OPEN’ release valve position used to lower the saddle.
4. saddle lowered, remove the oil Insert handle into handle socket and pump 6to full strokes.
5. that rolls freel . Raise and lower the unloaded saddle the into
eilmessadnastrapdeamadronrowecalpeR.lhtoomssetarepopmupehterusneotecivres
Bleeding / Venting Trapped Air
the release valve in the position and with saddle lowered, locate and remove the oil
r.
PREPARATION
Assembly
1.
2.
provided.
3.
8&9).
12 & 13).
4.
5.
!Ensure all fasteners are secure before use.
hydraulic unit
7
11
14 onto the saddle.
Figure 2- ATD-7429 Assembly

4
r r
!ADVERTENCIA
OPERATION
Raise Saddle Assembly
!
Lower Saddle Assembly
Be sure all tools and personnel are clear before
lowering load. Slowly open the release valve!
Themoreyouturntheknobcounterclockwise,thefaster
the load will come down. Maintain control of the rate of
speed at which the load lowers at all times!
. Slowly, gently,
Ensure the transmission is centered on the
jack.An off-center load could cause the jack to tip
over resulting in personal injury or property damage.
!
!WARNING
Read, understand, and follow
before use
Do not
only
Adequately support the vehicle before
starting repairs.
lowest possible position
ifting platform is level
limited to removal,
installation, and transportatio
automotive and light
truck transmissions, transfer cases and
transaxles
rated
capacity is greater
center loaded
Transfer load immediately
Be alert sober
Failure to heed result
personal injury and/or property damage
!WARNING
Tcrushing and related injuries
NEVER
Transfer
2. Follow vehicle manufacturer’s recommended

5
MAINTENANCE
Important: oil. Avoid different of and NEVER use
transmission motor oil or Improper can cause premature failure of the and the
potential for sudden and immediate loss of load.
Adding oil
2.
Changing oil
.
.
Note.
Lubrication
A periodic of oil to pivot and will help to prevent rust and assure that
.
Cleaning
check the pump piston and ram for of rust or corrosion. Clean as needed and wipe with an
cloth.
Note:
Storage
TROUBLESHOOTING
noitcAevitcerroCsesuaCelbissoPmotpmyS
Jack will not lift load
pressure your
Poor lift performance
distributor.

ITEM# ORDERING PART# DESCRIPTION QTY ITEM# ORDERING PART# DESCRIPTION QTY
18
29
310
411
512
613
7 PRT7429-07 HYDRAULIC UNIT 1 14
NOT SHOWN: PRT7429-SK - SEAL KIT
PRT7429-08-14 SADDLE ASSEMBLY 1
PRT7429-03-06 BASE HALF 2
PRT7429-01-02 CASTER ASSY (SET OF 4) 1
6
REPLACEMENT PARTS
Not all components of this product are replacement items, but are illustrated as a convenient reference for position in
the assembly sequence. When ordering parts, give model number, part number and description. Call your distributor
for current pricing:
1
2
6
7
8
9
10
11 12
13
14
2
1
1
1
2
6
345
3
4
5

7
DATE MAINTENANCE PERFORMED
PREVENTATIVE MAINTENANCE RECORD LOG

WARRANTY
1 YEAR LIMITED WARRANTY
THIS WARRANTY AND CONFIRMED RECEIPT(S) SHOULD BE RETAINED BY THE CUSTOMER AT ALL TIMES
PURCHASED FROM: _______________________________________
DATE PURCHASED: ________________________________________
INVOICE/RECEIPT NUMBER: _________________________________________
Your ATD-7429 is warranted for a period of 12 months from the original purchase date.
For a period of one (1) year from your purchase date, ATD Tools, Inc. will repair or replace (at its option) without charge, your
ATD product if it was purchased new and the product has failed due to a defect in material or workmanship which you experienced
during normal use of the product. This limited warranty is your exclusive remedy.
To access the benefits of this warranty, contact your supplier, or point of sale directly. You may be advised to return the product
under warranty, freight prepaid, to your supplier for warranty determination.
If this ATD product is altered, abused, misused, modified, or undergoes service by an unauthorized technician, your warranty will
be void. We are not responsible for damage to ornamental designs you place on this ATD product and such ornamentation should
not cover any warnings or instructions or they may void the warranty. This warranty does not cover scratches, superficial dents, and
other abrasions to the paint finish that occur under normal use. It also does not cover normal wear items such as but not limited to
brushes, batteries, drill bits, drill chucks, pads or blades.
Subject to the law in your state:
(1) Your sole and exclusive remedy is repair or replacement of the defective product as described above.
(2) ATD is not liable for any incidental damages, including but not limited to, lost profits and unforeseeable consequences.
(3) The repair and replacement of this product under the express limited warranty described above is your exclusive remedy and is
provided in lieu of all other warranties, express or implied. All other warranties, including implied warranties and warranties of
merchantability or fitness for a particular purpose are disclaimed and, if disclaimer is prohibited, these warranties are limited to
one year from your date of purchase of this product.
Some states’ laws do not allow limited durations on certain implied warranties and some states’ laws do not allow limitations on
incidental or consequential damages. You should consult the law in your state to determine how your rights may vary.
[Affix receipt or invoice here for safe keeping]