ATD Tools ATD-7317 Service manual

7137-DTA:ledoM noT2:yticapaC
1
ATD-7317
Low ProĮle Service Jack
Capacity Min. Height Max Height Handle
Length
Overall
Length
Overall
Width
Saddle
Diameter
Shipping
Weight
2 Ton 2 3/4” 24” 49-1/4” 36” 15-1/8” 4” 106 LB
Contents:
Page: 1. SpeciĮĐĂƟons
2. Safety & Warning /ŶĨŽƌŵĂƟŽŶ
3. & 4. Setup, OperĂƟŽŶ & PreveŶƟve Maintenance
5. InspĞĐƟon, Storage & TroubleƐŚŽŽƟŶŐ
6. Exploded View & Replaceable Part Numbers
7. Warranty /ŶĨŽƌŵĂƟŽŶ
8. PreveŶƟve Maintenance Record Log
O
p
ĞƌĂƟn
g
InstrucƟŽŶs & Parts Manual

7137-DTA:ledoM noT2:yticapaC
2
SAFETY & WARNING INFORMATION
IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE
Before ŽƉĞƌĂƟŶŐ this device, be sure to read all content within this manual, ensuring that you
understand the ŽƉĞƌĂƟŶŐ procedures, maintenance requirements and all safety warnings.
The owner and/or operator shall have an understanding of the product, its opĞƌĂƟng
characteriƐƟcs, and safety opĞƌĂƟng instrƵĐƟŽŶƐ before ŽƉĞƌĂƟŶŐ this device. Safety informaƟon
shall be emphasized and understood. If the operator is not ŇƵent in English, the product and
safety ŝŶƐƚƌƵĐƟŽŶƐ shall be read to and discussed with the operator in the operator’s ŶĂƟǀĞ
language by the purchaser/owner or his designee, making sure that the operator comprehends
their contents.
AcƟŽŶs to help prevent dangerous ƐŝƚƵĂƟŽŶs
Study, understand, and follow all instruĐƟons before ŽƉĞƌĂƟŶŐ this device.
Do not exceed the rated capacity stated.
Use only on hard level surfaces.
This item is to be used as a ůŝŌŝŶŐ device only. Immediately aŌer ůŝŌŝŶŐ support the
vehicle with appropriate means.
Do not move or dolly the vehicle while it is on the jack.
>ŝŌ only on areas of the vehicle as specŝĮed by the vehicle manufacturer.
No alƚĞƌĂƟons shall be made to this product.
Failure to heed these markings may result in serious personal injury and/or property
damage.
This is the safety ŶŽƟĮĐĂƟon symbol.
This symbol will ŶŽƟĨLJ you of any
potenƟal injury hazards. Please
follow all instrucƟŽŶƐ that follow this
symbol to avoid possible injuries or
death.
Indicates a hazardous
ƐŝƚƵĂƟŽŶ If proper steps are
not followed, death or
serious injury could result.

7137-DTA:ledoM noT2:yticapaC
3
SETUP, OPERATION & PREVENTIVE MAINTENANCEΎ
Setup
Prior to each use, visual inspeĐƟŽŶ (See Pg. 5) shall be made to the device by checking
for abnormal ĐŽŶĚŝƟŽŶƐ such as cracked welds, leaks, and damaged, loose, or missing
parts.
Consult the vehicle owner’s manual to determine the ůŽĐĂƟŽŶ of ůŝŌ points.
Be sure to set the vehicle in park with the emergency brake on and wheels securely
chocked.
Be sure that the vehicle and the jack are on a hard, level surface.
Assembly
If two piece handles are provided, assemble the upper ƐĞĐƟon into the lower secƟŽŶ
line up the holes, insert and Ɵghten the screw.
Insert the ďŽƩŽŵ end of handle into handle fork and securely Ɵghten the bolt and
washer. Ensure the handle can turn freely.
LiŌing
Turn the handle/release valve clockwise to the closed ƉŽƐŝƟŽŶ Do not over Ɵghten.
WŽƐŝƟŽŶ the jack under the specŝĮed ůŝŌ point.
Begin ůŝŌŝŶŐ by pumping the handle up and down.
Immediately ĂŌer ůŝŌŝŶŐ support the vehicle with appropriately rated jack stands.
Turn the handle/release valve slowly counterclockwise to lower the vehicle onto jack
stands.
Lowering
Turn the handle/release valve clockwise to the closed ƉŽƐŝƟŽŶ Do not over Ɵghten.
Pump the handle up and down to liŌvehicle Žī jack stands.
Remove the jack stands. Do not get under or let anyone get under the vehicle while
lowering.
Turn the handle/release valve slowly counterclockwise to lower the vehicle onto the
ground
.

7137-DTA:ledoM noT2:yticapaC
4
SETUP, OPERATION & PREVENTIVE MAINTENANCE (Cont.)
Maintenance
Ύ
NOTICE: Use high grade hydraulic oil only. Never use brake ŇƵŝĚ motor oil, transmission ŇƵŝĚ
turbine oil or any other ŇƵŝĚƐ ISO-VG22 or equivalent hydraulic oil is recommended.
Check and ZĞĮll Oil
With the jack in the fully lowered, level ƉŽƐŝƟŽŶ if unit cover is provided, remove unit
cover, then remove oil Įller plug.
Proper oil level should be just covering inner cylinder as seen from the oil Įller plug
hole.
Do not ŽǀĞƌĮll. Always Įůů with new, clean hydraulic jack oil as recommended above.
Reinstall oil Įller plug, then reinstall unit cover.
LubricĂƟŽn and Cleaning
Periodically clean and lubricate all moving parts and pivot points.
Air sĞŶƟŶg Procedures
With the jack in the fully lowered ƉŽƐŝƟŽŶ release valve open, remove oil Įller plug.
Pump the handle rapidly several ƟŵĞƐ Reinstall oil Įller plug.
Turn the handle/release valve clockwise to the closed ƉŽƐŝƟŽŶ
Pump the handle ƵŶƟů the ůŝŌ arm reaches maximum height and conƟnue to pump
several Ɵmes to remove trapped air in the system.
Turn the handle/release valve counterclockwise in one full turn and lower ůŝŌ arm to the
lowest posiƟon. Use force on saddle if necessary.
Carefully and slowly loosen oil Įller plug to release pressurized air.
Repeat above steps ƵŶƟů trapped air is completely vented.
Damaged Equipment
Any jack that appears to be damaged in any way, is found to be worn, or operates abnormally
SHALL BE REMOVED FROM SERVICE UNTIL REPAIRED. It is recommended that necessary repairs
be made by a manufacturer’s or supplier’s authorized repair facility if repairs are permiƩĞd by
the manufacturer or supplier.
AlterĂƟŽŶs
Because of poteŶƟĂů hazards associated with this type of equipment, no alƚĞƌĂƟons shall be
made to the product.
ƩĂchments and Adapters
Only ĂƩĂchments and/or adapters supplied by the manufacturer shall be used.

7137-DTA:ledoM noT2:yticapaC
5
INSPECTION, STORAGE & TROUBLESHOOTING
/ŶƐƉĞĐƟŽn
Visual inspeĐƟŽŶ shall be made before each use of the device by checking for abnormal
ĐŽŶĚŝƟŽŶƐ such as cracked welds, leaks, and damaged, loose, or missing parts.
Other inspecƟŽŶƐ shall be made per product operĂƟŶŐ ŝŶƐƚƌƵĐƟŽŶƐ
This device shall be inspected immediately if the device is believed to have been
subjected to an abnormal load or shock. It is recommended that this inspĞĐƟon be made
by a manufacturer’s or supplier’s authorized repair facility.
Owners and/or operators should be aware that repair of this equipment may require
specialized knowledge and faciliƟes. It is recommended that an annual inspeĐƟŽŶ of the
product be made by a manufacturer’s or supplier’s authorized repair facility and that
any defeĐƟve parts, decals, or safety labels or signs be replaced with manufacturers or
supplier’s specŝĮed parts.
Storage
This Jack should be stored in a dry locaƟŽn on a level surface.
TroubleshŽŽƟngΎ
Symptom Possible Causes ^ŽůƵƟŽn
Jack will not ůŝŌ the load. 1. Release valve not ƟŐhtly
closed.
2. Low oil level.
3. DefeĐƟǀe or worn internal
parts.
4. Load exceeds maximum
allowance.
1. Tighten release valve.
2. Check and add oil. Follow “Check
and ZĞĮůů Oil” instrucƟons on Pg.4.
3. DisconƟnue use and contact a
local repair center.
4. Use a higher capacity jack.
Jack will not hold the load. 1. Release valve not ƟŐhtly
closed.
2. Power unit malfunĐƟŽn.
1. Tighten release valve.
2. DisconƟnue use and contact a
local repair center.
Jack will not descend to
minimum height, or will not
remain in lowered posŝƟŽŶ.
1. Air trapped in system.
2. Reservoir oil oǀĞƌĮlled.
1. Vent air out of system. Follow
“Air
VeŶƟng Procedures” above.
2. Check and ensure proper oil
level. Follow “Check and ZĞĮll Oil”
ŝŶƐƚƌƵĐƟŽŶ on Pg.4.
Jack will not ůŝŌ to max
height.
1. Low oil level. 1. Check and ensure proper oil level.
Follow “Check and ReĮůl Oil”
insƚƌƵĐƟŽŶƐ above.
Jack will not funcƟŽn
properly aŌer tried sŽůƵƟŽŶ.
1. Internal malfuncƟŽŶ or
structural damage.
1. Stop usage and contact an
authorized repair center.

7137-DTA:ledoM
noT2:yticapaC
6
EXPLODED VIEW & REPLACEABLE PART NUMBERS
* Items not ide ed by part number are not available for replacement.
1
2
346
7
8
9
5
10
11
13
12
Item Part Number* Descripon Q’ty
1LYD2G-100 Front Wheel Assembly 2
2LYD2K-300 Saddle w/ Pad 1
3GB1152-89-M6 Grease Fing 1
4LYD3J-3 Cover 1
5LYD3F-600 Handle Assembly w/ Foam 1
6LYD2-9A Return Springs 2
7LYDBI-2T.3 Power Unit Assembly 1
8LYD3G-300 Handle Fork Assembly 1
9LYD3G-400 Rear Caster Assembly 2
10 LYDBI-3T-17 Handle Foam only 1
11 LYD2K-3B Saddle Pad only 1
12 LYD3F-100 Oil Filler Screw w/ Seal 1
13 LYD3G-101 U-Joint 1
N/A ATD7317-L Label 1

7137-DTA:ledoM noT2:yticapaC
7
WARRANTY INFORMATION
ONE YEAR LIMITED WARRANTY
For a period of one (1) year from your purchase date, ATD Tools, Inc. will repair or replace (at its
option) without charge, your ATD product if it was purchased new and the product has failed
due to a defect in material or workmanship which you experienced during normal use of the
product. This limited warranty is your exclusive remedy.
To access the benefits of this warranty, contact the ATD warranty center at 1-844-364-9922 for
confirmation that this warranty applies. Thereafter, you may be advised to return the product
under warranty, freight prepaid, to the ATD Tools, Inc. service department.
If this ATD product is altered, abused, misused, modified, or undergoes service by an
unauthorized technician, your warranty will be void. We are not responsible for damage to
ornamental designs you place on this ATD product and such ornamentation should not cover
any warnings or instructions or they may void the warranty. This warranty does not cover
scratches, superficial dents, and other abrasions to the paint finish that occur under normal use.
Subject to the law in your state:
(1) Your sole and exclusive remedy is repair or replacement of the defective product as
described above.
(2) ATD Tools, Inc. is not liable for any incidental damages, including but not limited to, lost
profits and unforeseeable consequences.
(3) The repair and replacement of this product under the express limited warranty described
above is your exclusive remedy and is provided in lieu of all other warranties, express or
implied. All other warranties, including implied warranties and warranties of
merchantability or fitness for a particular purpose are disclaimed and, if disclaimer is
prohibited, these warranties are limited to one year from your date of purchase of this
product.
Some states’ laws do not allow limited durations on certain implied warranties and some states’
laws do not allow limitations on incidental or consequential damages. You should consult the
law in your state to determine how your rights may vary.
Made in China to ATD Tools, Inc. SpeciĮĐĂƟons
Visit us at www.atdtools.com
Warranty Service Number 1-844-364-9922
For Non-warranty issues, please contact your supplier.
Printed In China

7137-DTA:ledoM noT2:yticapaC
8
PREVENTIVE MAINTENANCE RECORD LOG
Date Maintenance Performed