
SAFETY AND GENERAL INFORMATION
Always keep work area clean.Clutteredareas inviteLQMXULHV Observe work area conditions.Donotusemachines
or power tools in damp or wet locations Do not H[SRVH to rain. Keep ZRUN area well OLJKWHG Do use HOHFWULFLDOO\
Keep children away. Children must never EH allowed
in the ZRUN area. Do not let them handle machines, tools, or H[WHQVLRQ cords. Store idle equipment. :KHQ not in
use, tools must EH stored in GU\ location to LQKLELW rust. $OZD\V ORFN up tools and NHHS out of reach of children. Use
the right tool for the job. Do not attempt to force a small tool or attachment to do the ZRUN of a ODUJHU industrial tool.
There are certain applications for which this tool was GHVLJQHG It will do the MRE EHWWHU and more VDIHO\ at the rate for
which it was intended. Do not PRGLI\ this tool and do not use this tool for a purpose for which is was not intended.
Dress properly. Do not wear loose FORWKLQJ or MHZHOU\ as WKH\ can EH FDXJKW in PRYLQJ parts. 3URWHFWLYH HOHFWULFDOO\
QRQFRQGXFWLYH clothes and QRQVNLG footwear are recommended when ZRUNLQJ :ear restrictive hair FRYHULQJ to
contain ORQJ hair. Use eye and ear protection. $OZD\V wear &( approved impact VDIHW\ JRJJOHV :ear a full face
Do not overreach. Keep proper IRRWLQJ and EDODQFH at all
WLPHV'RQRWUHDFKRYHURUDFURVVUXQQLQJPDFKLQHV
- Service Jack -
y
Do not exceed rated capacity.
Use jack only for lifting.
Place jack correctly. y
Stabilize the load. y
r
WARNING
Save these instructions. You will need the manual for the VDIHW\ ZDULQLQJV and precautions, DVVHPEO\ instructions,
RSHUDWLQJ and maintenance procedures, parts list and GLDJUDP Keep \RXU invoice with this manual. :rite the invoice
QXPEHU on the inside of the front cover. Keep the manual and invoice in asafe and dr\place for future reference. For
\ouUVDIHW\ read, understand, and follow the information provided with and on this device EHIRUH XVLQJ The owner
DQG RU operator should have an XQGHUVWDQGLQJ of the device, its RSHUDWLQJ characteristics and VDIHW\ RSHUDWLQJ
LQVWUXFWLRQVEHIRUH RSHUDWLQJ the HTXLSPHQW The owner DQGRU operator should EH aware that use and repair of this
product PD\ UHTXLUH special VNLOOV and NQRZOHGJH Instructions and VDIHW\ information should EH read to and
discussed with the operator in the operator's native ODQJXDJH PDNLQJ sure that the operator comprehends their
contents, EHIRUH use of this HTXLSPHQW is DXWKRUL]HG If DQ\ GRXEW H[LVWV as to the safe and proper use of this device,
!
remove from VHUYLFHLPPHGLDWHO\
Inspect before each use. Do not use if DEQRUPDO conditions such as FUDFNHG welds, GDPDJHG loose or PLVVLQJ
partsare noted.$Q\ HTXLSPHQW that appearsGDPDJHG in DQ\ ZD\ isfound toEH worn, oroperates DEQRUPDOO\ should
EH removed from service until repaired. If the HTXLSPHQW has EHHQ or is suspected to have EHHQ VXEMHFWHG to an
DEQRUPDO load or VKRFN LPPHGLDWHO\ discontinue use until inspected E\ a IDFWRU\ DXWKRUL]HG repair IDFLOLW\ (contact
GLVWULEXWRU or manufacturer for list of DXWKRUL]HG repair facilities). It is recommended that an annual inspection EH
PDGH E\ DQ DXWKRUL]HG UHSDLU IDFLOLW\ /DEHOV DQG RSHUDWRUV PDQXDOV DUH DYDLODEOH IURP WKH PDQXIDFWXUHU