ATD Tools 7514 User manual

ATD7514_rev_0421
ATD-7514
4-TON SERVICE JACK
OWNER’S MANUAL
4-Ton Service Jack
Features:
([FOXVLYH6ZLIW/LIW7HFKQRORJ\RIIHUVDTXLFNHUOLIWIRUSURIHVVLRQDOSHUIRUPDQFH
+LJKPD[LPXPOLIWLVLGHDOIRU689VWUXFNVWUDLOHUVDQGRWKHUKLJKFOHDUDQFHYHKLFOHV
'XDOSXPSSLVWRQVDUHVKLHOGHGWRSUHYHQWFRQWDPLQDQWVIURPGDPDJLQJWKHK\GUDXOLFV\VWHP
,QWHUQDOE\SDVVYDOYHSURWHFWVWKHK\GUDXOLFV\VWHPIURPRYHUSXPSLQJ
8-RLQWUHOHDVHPHFKDQLVPSURYLGHVSUHFLVHFRQWURORIORDGGHVFHQWLQDQ\KDQGOHSRVLWLRQ
+HDY\JDXJHFRQVWUXFWLRQIHDWXUHVUROOHGHGJHVIRUDGGHGVWUHQJWK
,QGXVWULDOJUDGHFDVWHUVRIIHUJUHDWHUVWDELOLW\DQGDOORZLQFUHDVHGPDQHXYHUDELOLW\DQG
HDV\SRVLWLRQLQJRIWKHMDFN
)XOOFRYHUUXEEHUVDGGOHSDGSURWHFWVWKHYHKLFOHIURPGDPDJHGXULQJOLIWLQJ
0HHWVRUH[FHHGV$60(3$6(VWDQGDUGV
0DGHLQ&KLQDWR$7'7RROV,QF6SHFLILFDWLRQV
9LVLWXVDWZZZDWGWRROVFRP
Specifications:
&DSDFLW\7RQV
/LIWLQJ5DQJH´´
6DGGOH'LDPHWHU´ZLWKVDGGOHSDG
+DQGOH/HQJWK´SLHFHZLWKSURWHFWLYHIRDP
-DFN6L]H´[´[´

Service Jack Model Number: ATD-7514
Capacity Min. Height Max Height
Jack Size
(L x W x H) Saddle Diameter Net Weight
4 Ton 85.8 LB
-28-1/4"x 13-5/8"x 7-7/16"
4-7/16” 19-7/8” 4"
2
SAFETY & WARNING INFORMATION
Before opera ng this device, be sure to read all content within this manual, ensuring that you
understand the opera ng procedures, maintenance requirements and all safety warnings.
The owner and/or operator should have an understanding of the product, its oƉĞƌĂƟŶŐ
characteris cs, and safety opera ng instruc ons before opera ng this device. Safety
informa on should be emphasized and understood. If the operator is not ŇƵĞŶƚ in English, the
product and safety instruc ons should be read to and discussed with the operator in the
operator’s na ve language by the purchaser/owner or his designee, making sure that the
operator comprehends their contents.
Study, understand, and follow all instruc ons before opera ng this device.
Do not exceed the rated capacity stated.
Use only on hard level surfaces.
This jack is to be used as a li ing device only. Immediately a er li ing, support the
vehicle with appropriate means.
Do not move or dolly the vehicle while it is on the jack.
Li only on areas of the vehicle as speci ed by the vehicle manufacturer.
No altera ons should be made to this product.
This is the safety n con
symbol. This symbol will n fy you
of any poten al injury hazards.
Please follow all instruc ons that
follow this symbol to avoid possible
injuries or death.
Indicates a hazardous
situa on. If proper steps are
not followed, death or
serious injury could result.
IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE
ACTIONS TO HELP PREVENT DANGEROUS SITUATIONS
WARNING
WARNING

Jack Stands are designed to support stated capacity. Stands should only be used to
support par al loads that consist of one end of a vehicle. Always use as a matched pair
to support one end of a vehicle only.
Never use jack stands to support both ends or one side of a vehicle.
Use only one (1) pair of stands per vehicle.
3
SETUP, OPERATION & PREVENTIVE MAINTENANCE
Prior to each use, visual inspec on (See Pg. 6) should be made to the device by checking
for abnormal condi ons, such as cracked welds, leaks, and damaged, loose, or missing
parts.
Consult the vehicle owner’s manual to determine the loca on of li points.
Be sure to set the vehicle in park with the emergency brake on and wheels securely
chocked.
Be sure that the vehicle and the jack are on a hard, level surface.
Service Jack
Assemble the upper sec on of the two piece handle into the lower sec on, line up the
holes, insert and ghten the screw.
Insert the bo om end of handle into handle fork and securely ghten the bolt and
washer. Ensure the handle can turn freely.
Turn the handle/release valve clockwise to the closed posi on. Do not over ghten.
Posi on the jack under the speci ed li point.
Begin li ing by pumping the handle up and down.
Immediately a er li ing, insert safety pins into the appropriately rated jack stands and
Turn the handle/release valve slowly counterclockwise to lower the vehicle onto jack
stands.
SETUP
ASSEMBLY
LIFTING
support the vehicle. NEVER support the vehicle with only the jack.
SAFETY & WARNING INFORMATIOE;ŽŶƟŶƵĞĚͿ
This jack is designed toƌĂŝƐĞƚŚĞǀĞŚŝĐůĞŶŽƚƚŽƐƵƉƉŽƌƚƚŚĞǁĞŝŐŚƚŽŶŝƚƐŽǁŶŽŶĐĞůŝŌĞĚ
Support the vehicle with jack stands as outlined below.

4
SETUP, OPERATION & PREVENTIVE MAINTENANCE ;ŽŶƟŶƵĞĚͿ
Turn the handle/release valve clockwise to the closed posi on. Do not over ghten.
Pump the handle up and down to li vehicle o jack stands.
Remove the jack stands and safety pins. DO NOT get under or let anyone get under
the vehicle while lowering.
Turn the handle/release valve slowly counterclockwise to lower the vehicle onto the
ground.
NOTICE: Use high grade hydraulic oil only. Never use brake uid, motor oil, transmission uid,
turbine oil or any other uids. ISO-VG22 or equivalent hydraulic oil is recommended.
Check and Re ll Oil
With the jack in the fully lowered, level posi on, if unit cover is provided, remove unit
cover, then remove oil ller plug.
Proper oil level should be just covering inner cylinder as seen from the oil ller plug hole.
Do not over ll. Always ll with new, clean hydraulic jack oil as recommended above.
Reinstall oil ller plug, then reinstall unit cover.
Lubr n and Cleaning
Periodically clean and lubricate all moving parts and pivot points.
Air Venting Procedures
With the jack in the fully lowered posi on, release valve open, remove oil ller plug.
Pump the handle rapidly several mes. Reinstall oil ller plug.
Turn the handle/release valve clockwise to the closed posi on.
Pump the handle un l the li arm reaches maximum height and con nue to pump
several mes to remove trapped air in the system.
Turn the handle/release valve counterclockwise in one full turn and lower li arm to the
lowest posi on. Use force on saddle if necessary.
Carefully and slowly loosen oil ller plug to release pressurized air.
Repeat above steps un l trapped air is completely vented.
LOWERING
SERVICE JACK MAINTENANCE
Any service jack that appears to be damaged in any way, is found to be worn, or operates
abnormally SHOULD BE REMOVED FROM SERVICE UNTIL REPAIRED. It is recommended that
necessary repairs be made by a manufacturer’s or supplier’s authorized repair facility if repairs
are permi ed by the manufacturer or supplier.
DAMAGED EQUIPMENT

5
SETUP, OPERATION & PREVENTIVE MAINTENANCE ;ŽŶƟŶƵĞĚͿ
Altera ons
Because of poten al hazards associated with this type of equipment, no altera ons should be
made to the product.
Aachments and Adapters
Only a achments and/or adapters supplied by the manufacturer should be used.
Oil Filler Plug
( Located on Reservoir) Handle
Handle Fork
Caster
Front Wheel
Lifting Arm
Saddle
INSPECTION, STORAGE & TROUBLESHOOTING
Visual inspec on should be made before each use of the device by checking for abnormal
condi ons, such as cracked welds, leaks, and damaged, loose, or missing parts.
Other inspec ons should be made per product opera ng instruc ons.
These devices should be inspected immediately if the device is believed to have been
subjected to an abnormal load or shock. It is recommended that this inspecon be made
by a manufacturer’s or supplier’s authorized repair facility.
Owners and/or operators should be aware that repair of this service jack may require
specialized knowledge and facili es. It is recommended that an annual inspec on of the
product be made by a manufacturer’s or supplier’s authorized repair facility and that
any defec ve parts, decals, or safety labels or signs be replaced with manufacturer’s or
supplier’s speci ed parts.
INSPECTION

6
The service jack and jack stands should be stored in a dry loca on on a level surface.
STORAGE
Symptom Possible Causes Solu on
Jack will not li the load. 1. Release valve not ghtly
closed.
2. Low oil level.
3. Defec ve or worn internal
parts.
4. Load exceeds maximum
allowance.
1. Tighten release valve.
2. Check and add oil. Follow “Check
and Re ll Oil” instruc ons on Pg.4.
3. Discon nue use and contact a
local repair center.
4. Use a higher capacity jack.
Jack will not hold the load. 1. Release valve not ghtly
closed.
2. Power unit malfunc on.
1. Tighten release valve.
2. Discon nue use and contact a
local repair center.
Jack will not descend to
minimum height, or will not
remain in lowered posi on.
1. Air trapped in system.
2. Reservoir oil over led.
1. Vent air out of system. Follow
“Air Ven ng Procedures” on Pg. 4.
2. Check and ensure proper oil level.
Follow “Check and Re ll Oil”
instruc on on Pg.4.
Jack will not li to max
height.
1. Low oil level. 1. Check and ensure proper oil level.
Follow “Check and Re ll Oil”
instruc ons on Pg. 4.
Jack will not func on
properly a er tried solu on.
1. Internal malfunc on or
structural damage.
1. Stop usage and contact an
authorized repair center.
TROUBLESHOOTING
&ŽƌĂƐƐŝƐƚĂŶĐĞƚƌŽƵďůĞƐŚŽŽƟŶŐƉůĞĂƐĞĐĂůůŽƵƌdŽůů Free Service Number 1-844-364-9922
INSPECTION, STORAGE & TROUBLESHOOTIN';ŽŶƟŶƵĞĚͿ

7
*Items not ideŶƟĮed by part number are not available for replacement.
EXPLODED VIEW & REPLACEABLE PART NUMBERS
1
2
3
4
6
5
7
8
PART NO. FACTORY NO. DESCRIPTION QTY
1 LYD3G-100 Front Wheel Assembly 2
2 LYD3G-PJ-2 Saddle W/ Pad 1
3 LYD3G-PJ-1A Handle Assembly w/ Foam 1
4 LYD3G-PJ-4 Power Unit Assembly 1
5 LYD3F-500 Handle Fork Assembly 1
6 LYD3G-PJ-6 Rear Caster Assembly 2
7 LYD3A-5 Return Springs 2
81
LYD3A-8A Saddle Pad
N/A ATD751
4 -L Product Label 1

8
WARRANTY
1 YEAR LIMITED WARRANTY
THIS WARRANTY AND CONFIRMED RECEIPT(S) SHOULD BE RETAINED BY THE CUSTOMER AT ALL TIMES
385&+$6(')520BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
'$7(385&+$6('BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
,192,&(5(&(,37180%(5BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
<RXU$7'LVZDUUDQWHGIRUDSHULRGRIPRQWKVIURPWKHRULJLQDOSXUFKDVHGDWH

)RUDSHULRGRIRQH\HDUIURP\RXUSXUFKDVHGDWH$7'7RROV,QFZLOOUHSDLURUUHSODFHDWLWVRSWLRQZLWKRXWFKDUJH\RXU
$7'SURGXFWLILWZDVSXUFKDVHGQHZDQGWKHSURGXFWKDVIDLOHGGXHWRDGHIHFWLQPDWHULDORUZRUNPDQVKLSZKLFK\RXH[SHULHQFHG
GXULQJQRUPDOXVHRIWKHSURGXFW7KLVOLPLWHGZDUUDQW\LV\RXUH[FOXVLYHUHPHG\
7RDFFHVVWKHEHQHILWVRIWKLVZDUUDQW\FRQWDFW\RXUVXSSOLHURUSRLQWRIVDOHGLUHFWO\<RXPD\EHDGYLVHGWRUHWXUQWKHSURGXFW
XQGHUZDUUDQW\IUHLJKWSUHSDLGWR\RXUVXSSOLHUIRUZDUUDQW\GHWHUPLQDWLRQ
,IWKLV$7'SURGXFWLVDOWHUHGDEXVHGPLVXVHGPRGLILHGRUXQGHUJRHVVHUYLFHE\DQXQDXWKRUL]HGWHFKQLFLDQ\RXUZDUUDQW\ZLOO
EHYRLG:HDUHQRWUHVSRQVLEOHIRUGDPDJHWRRUQDPHQWDOGHVLJQV\RXSODFHRQWKLV$7'SURGXFWDQGVXFKRUQDPHQWDWLRQVKRXOG
QRWFRYHUDQ\ZDUQLQJVRULQVWUXFWLRQVRUWKH\PD\YRLGWKHZDUUDQW\7KLVZDUUDQW\GRHVQRWFRYHUVFUDWFKHVVXSHUILFLDOGHQWVDQG
RWKHUDEUDVLRQVWRWKHSDLQWILQLVKWKDWRFFXUXQGHUQRUPDOXVH,WDOVRGRHVQRWFRYHUQRUPDOZHDULWHPVVXFKDVEXWQRWOLPLWHGWR
EUXVKHVEDWWHULHVGULOOELWVGULOOFKXFNVSDGVRUEODGHV
6XEMHFWWRWKHODZLQ\RXUVWDWH
<RXUVROHDQGH[FOXVLYHUHPHG\LVUHSDLURUUHSODFHPHQWRIWKHGHIHFWLYHSURGXFWDVGHVFULEHGDERYH
$7'LVQRWOLDEOHIRUDQ\LQFLGHQWDOGDPDJHVLQFOXGLQJEXWQRWOLPLWHGWRORVWSURILWVDQGXQIRUHVHHDEOHFRQVHTXHQFHV
7KHUHSDLUDQGUHSODFHPHQWRIWKLVSURGXFWXQGHUWKHH[SUHVVOLPLWHGZDUUDQW\GHVFULEHGDERYHLV\RXUH[FOXVLYHUHPHG\DQGLV
SURYLGHGLQOLHXRIDOORWKHUZDUUDQWLHVH[SUHVVRULPSOLHG$OORWKHUZDUUDQWLHVLQFOXGLQJLPSOLHGZDUUDQWLHVDQGZDUUDQWLHVRI
PHUFKDQWDELOLW\RUILWQHVVIRUDSDUWLFXODUSXUSRVHDUHGLVFODLPHGDQGLIGLVFODLPHULVSURKLELWHGWKHVHZDUUDQWLHVDUHOLPLWHGWR
RQH\HDUIURP\RXUGDWHRISXUFKDVHRIWKLVSURGXFW
6RPHVWDWHV¶ODZVGRQRWDOORZOLPLWHGGXUDWLRQVRQFHUWDLQLPSOLHGZDUUDQWLHVDQGVRPHVWDWHV¶ODZVGRQRWDOORZOLPLWDWLRQVRQ
LQFLGHQWDORUFRQVHTXHQWLDOGDPDJHV<RXVKRXOGFRQVXOWWKHODZLQ\RXUVWDWHWRGHWHUPLQHKRZ\RXUULJKWVPD\YDU\
>$IIL[UHFHLSWRULQYRLFHKHUHIRUVDIHNHHSLQJ@