Atdec A-STSWW-A User manual

A-STSWW-A Page 1 of 5
Installation Instructions
Wall Mounted
Sit-to-Stand Workstation - Antimicrobial
Component Checklist
Step 1. Check Components
ABC D E
Lower Arm Upper Arm Vertical Screen
Slider Keyboard Tray Tilt Head
A-STSWW-A
• 8mm wrench
• Drill
• 10mm masonry bit
• 4.5mm drill bit
• Ratchet
• Spirit Level
• Stud Finder
• Pencil
5mm Allen 6mm Allen2.5mm Allen
M6X8 (x1) M4x10 (x4)M6X12 (x4)M8X20 (x1)
8mm
¼” Drive
Velcro
Strip (x2)
H J K L M N
PO Q R S T
Tools Required
Plastic
Washer (x1)
Coach
Screw (x6) Nylon Anchor (x6)
Metal
Washer (x1)
M6X10 (x3)
Hardware
FG
Wall Mounting Hardware
Check that you have received all parts against the Component Checklist.
! IMPORTANT - Install as per Installation Instructions
! The manufacturer accepts no responsibility for incorrect installation.
! This product supports a maximum load 8Kg (17.6lbs.)
! The wall mount can be installed on vertical, at, solid concrete or brick walls, or timber stud walls only.
! Thewallshouldbestrongenoughtosustainaweightofatleastfourtimesthatofthedisplayandwallmountbracketcombined.
If in doubt, consult a structural engineer.
! Checkwallanchorsandscrewsevery3monthsfromthetimeofinstallationtoensuretheworkstationisrmlyxedtothewall.
! Tighten all screws (do not exert excessive force to avoid breaking the screws or damaging their thread)
IMPORTANT INFORMATION

A-STSWW-A Page 2 of 5
2.3
2.4
2.5
F
L
A
G
Wall Plate
Remove top and
bottom covers from
the wall plate.
Push nylon
anchors into
each hole.
Fix wall plate to
the wall using 6
coach screws
10mm
55mm
Wall 2.1
2.2
H
o
l
e
D
i
m
e
n
s
i
o
n
s
Spirit
Level
2.3
2.4
F
L
A
Wall Plate
Remove top and
bottom covers from
the wall plate.
Fix wall plate to
the wall using 4
coach screws
4.5mm
55mm
Stud
2.2
H
o
l
e
D
i
m
e
n
s
i
o
n
s
2.1
Spirit
Level
Step 2. Option B - Stud wall installation
Tip: Screw in the top coach screw rst.
Usethesuppliedtemplate
to mark and drill 4 holes
into the wall.
Two people
required
Note: Use a stud nder to ensure
all holes are drilled into the stud.
Step 2. Option A - Masonry or cement wall installation
Tip: Screw in the top coach screw rst.
Usethesuppliedtemplate
to mark and drill 6 holes
into the wall.
Two people
required
Note: For optimum performance, use a spirit
level to ensure straight installation.

A-STSWW-A Page 3 of 5
5.1 Drop screw head into
keyhole slot in upper
arm plate.
JQ
5.2
Screw limits screen
rotation to 90°
Remove screw for
360° rotation
90°360°
E
S
R
N
O
K
M
B
A
5mm
Note: do not tighten screw ‘Q’
J
P
Q
C
D
4.1 4.2
Step 4. Assemble slider to keyboard trayStep 3. Assemble upper arm
Step 5. Assemble slider to keyboard tray
Step 6. Attach tilting head to screen Step 7. Attach screen to arm Step 8. Replace covers

A-STSWW-A Page 4 of 5
J
H
Screen Height Tension
Tension Adjustment Points
Screen Tilt Tension
+35°
-5°
90°
L
+65°
-30°
HK
K
Keyboard Tray Storage
Mouse Tray PositionArm Height Tension
Arm Rotation Joint Tension
Adjusting
Note: Arm must be
in highest position
to access tension
adjustment point.
Note: Supplied velcro strips secure
the keyboard when stowed.
The keyboard tray can be
folded away for storage.
Themousetraycanbepositioned on
the left or right of the keyboard tray.

A-STSWW-A Page 5 of 5
T
T
Wash parts in
warm soapy
water.
Push in tab to
remove mouse
tray.
• Detach lower arm cable
cover by removing 6 screws.
• Route cables through the
cavity in the arm, then
reattach the cover.
Note: Ensure there is sucient slack in the cables to
accommodate the workstation’s range of movement.
The upper arm cable
cover is detached by
pulling near the top of
the cover.
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specications without notice. ©20190814
atdec.com
Cable Management. Route cables through arm.
Secure Keyboard Attach velcro to keyboard and tray Cleaning
Wrist pad and mouse tray can
be removed for cleaning.

Stud Wall
Drilling Template
Only drill holes marked with an ‘X’
OR
OR
OR
Masonry Wall
Drilling Template
Only drill holes marked with an ‘X’