Atdec SYSTEMA SW6S User manual

SW6S
SW6SW
Component Checklist
Wall Channel (x1)
! IMPORTANT - Install Systema Wall Channel as per installation instructions.
! Refer to Systema Monitor arm or Monitor Spring Arm Installation Instructions for maximum load advice.
! The manufacturer accepts no responsibility for incorrect installations.
! The Systema Wall Channel is compatible with Systema Monitor Spring Arm: SS and with Systema Monitor Arms: SA13,
SA46, and SA71.
IMPORTANT INFORMATION:
Step 1. Check Components
Check what you have received against the component checklist and hardware above.
Nylon Anchor (x2)
Top Cap Screws
(x2)
Top Cap (x1)
SYSTEMA
Installation Instructions
Systema | 60mm Wall Channel
Step 2. Position Wall plate - Ergonomic Guidelines
Many experts believe that the extended use of any computer screen has the potential to cause serious injury to your eyes,
neck and back. This can be largely avoided by correctly positioning your display.
Viewing angle: Ergonomists recommend that the optimal position
of your display should be slightly below eye level. When looking at
the display’s centre the user should have a downward visual angle of
approximately 10°-20°.
Height: As a guide, the height (h) of your display should approximately
be as follows:
- Tall Male (Max): 560mm (22”)
- Short Male (Min): 368mm (14.5”)
- Tall Female (Max): 520mm (20.5”)
- Short Female (Min) 356mm (14”)
When used with the Systema Monitor Spring Arm, it is
recommended that the bottom of the wall channel is
positioned 50mm above the worksurface to facilitate use by
the largest range of people.
Distance: For visual comfort, a viewing distance (d) between 500mm
(20”) to 750mm (29.5”) is recommended.
10º -20º
50mm (2”)
Guidelines based on a
720mm (28.3”) high
worksurface
(h)
(d)
Systema Monitor
Spring Arm ‘SS’ Shown
Please refer to the
Systema range Technical
Specifications for
dimensional details
Tools Required:
• Power Drill
• 5.5mm (1/4”) Drill Bit
• 8mm (5/16”) Drill Bit
• Phillips Head Screwdriver
M6 x 50mm
Countersunk
Screw (x2)

Step 3. Install Wall Channel
Nylon
Anchors
8mm (0.3”)
holes
M6 x 50mm
Countersunk
Screw
Systema
Monitor Arm
or Monitor
Spring Arm
Top Cap
Top Cap
Screws
M6 x 50mm
Countersunk
Screw
Systema
Monitor Arm
or Monitor
Spring Arm
Top Cap
Screws
Top Cap
5.5mm (0.2”)
holes
Installation Complete
You are now ready to install your Systema Monitor Spring Arm.
Please refer to the Installation Instructions Included with these products.
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 26.03.14 ©
Masonry Timber Stud

SSS
SSW
Component Checklist
Systema | Monitor Spring Arm
VESA monitor headArm Assembly
! IMPORTANT - Install Systema Monitor Spring Arm as per installation instruction.
! This product supports a minimum load of 1.5kg (3.3lbs) and maximum load of 8kg (17.6lbs).
! The manufacturer accepts no responsibility for incorrect installation.
! Compatible with Systema Posts: SP10, SP40, SP75 and Wall Channels: SW6 & SW35.
IMPORTANT INFORMATION:
Step 1. Check Components
Check what you have received against the component checklist and hardware above.
Step 2. Mount Arm Assembly
M4 x 12/16/25mm (x4)
Black Phillips Head Mounting Screws
3/4mm Allen Keys
HARDWARE
Display Mounting Screws
Display Mounting
Spacers (x4)
M4 x 14mm (x1)
Silver Phillips Head
Security Screw
SYSTEMA
Installation Instructions
2.1 Remove Post Top Cap.
Existing Systema Post
2.2 Insert Arm Assembly into Channel
Note: Ensure Clamp
Head Lever is vertical
and unlocked.
Note: Squeeze and hold Clamp Head before
inserting into the channel on Post Assembly or
Wall Channel. Arm Assembly
Pole Assembly
2.4 Lock Channel Clamp at
preferred height.
‘Click’
Allen Key
Post Top Cap
Post Assembly
2.5 Insert Post Top Cap into Post Assembly.2.3 Move Channel Clamp to desired
height and ensure arm is supported.
Note: An Allen Key
may be stored in the
Post Top Cap.
Wall Channel

x
100mm
Spacers (may be required for
recessed and uneven surfaces)
VESA monitor head
VESA monitor head
Gap No Gap
3mm Allen Key
4mm Allen Key
Loosen
Tighten
Security Screw
Hole
Spring Tension
Adjustment
M4 x 14mm
Security Screw
Monitor head
screw
Arm Assembly
Screen
M4x12/16/25mm
Phillips Head Mounting Screws
100mm 75mm
75mm
+ Tighten Loosen -
Step 3. Install VESA monitor head
Step 4. Mount Display
4.1 Insert VESA monitor head into the receptacle in the Arm
Assembly.
4.2 Ensure that the VESA monitor head sits flush within the
Arm Assembly receptacle. There should be no gap.
4.3 Once the VESA monitor
head is sitting flush, push
the lever down to secure it
to the Arm Assembly.
4.4 OPTIONAL
Ensure the Monitor is supported,
then loosen the Monitor head
screw with the 3mm Allen Key
and tilt screen up before installing
the M4 x 14mm Security Screw
into the Security Screw hole.
Step 5. Adjust Spring Tension
5.1 To ensure the monitor will stay in position anywhere
within its range of movement, the spring tension on the
arm will need to be adjusted to suit the weight of the
monitor.
Note: Ensure the Lever is
flicked up before installation
onto the Arm Assembly.
3.1 Install VESA monitor head as shown.
Support the weight of the
monitor at a high position
(as shown) and tighten the
spring tension until you
feel the arm supporting the
weight of the monitor.
Note: Support
Screen when
adjusting tilt.

Cable Cover
Cable
6.1 Plug your cables into the
monitor and follow this cable
management system route.
6.2 Loop the cable
and push it through the
Forearm Cable Clip gap.
6.4 Push the cable up into the gap in the lower
arm Cable Cover.
6.5 Whilst maintaining pressure on the
cable, slide the cable into the groove and
follow it up.
6.6 Whilst maintaining pressure on the
cable, slide the cable into the groove and
follow it down.
6.3 At the Elbow, pull one
side of the clip down and
push the cable through
the gap.
5.2 Push the monitor down to
the bottom. If the screen bounces
back this may indicate too much
tension. Loosen the spring tension
1 turn at a time until no bounce
is observed.
Once adjustments have been
made, move the arm assembly
through the full range of movement
to ensure it moves freely and holds
its position.
Spring Tension Gauge
Red Marker
Step 6. Cable Management
Step 5. Adjust Spring Tension (cont.)
5.3 MULTIPLE ARM INSTALLATIONS
When installing multiple SYSTEMA products using
monitors of the same weight, observe the location of
the red marker on the Spring Tension Gauge and
set the tension to the same position on all arms.
Note: Ensure enough cable slack
is given to allow for movement.
Max weight: 8 kg.

Cable Cover Optional Cable Cover Positions
6.7 Under the Channel
Clamp, pull one side of the
clip down and push the cable
through the gap.
6.10 OPTIONAL (NOTE: Cable clips only come with SP40
and SP75 Posts or separately in SC4 accessory pack)
A. Push the cable down into the
Cab
Cab
le
le Clip.
6.9 OPTIONAL
A. Loop cable and insert into Cable Cover.
Step 6. Cable Management (cont.)
6.10 OPTIONAL
B. Insert one side of the Cable Clip into the Channel on the Post assembly or Wall
channel, before pushing the other side in.
Note: Choose 6.9 and/or 6.10 for your column cable management depending on your needs.
6.9 OPTIONAL
B. Push the Cable down into either side of the Cable Cover until it reaches the bottom.
6.8 OPTIONAL (NOTE: The Cable Cover shown,
only comes with SP40 or SP75 posts.)
To reposition the Cable Cover, pull it straight up and
out of the post and insert it into any of the available
slots.

10º - 20º
5º 15º
(h)
Post Cable Clip
3mm Allen Key
Installation Complete
Step 7. Adjusting the Display Bracket
Ergonomic Guidelines
Many experts believe that the extended use of any computer screen has the potential to cause serious injury to your eyes,
neck and back. This can be largely avoided by correctly positioning your display.
Viewing angle: Ergonomists recommend that the optimal position
of your display should be slightly below eye level. When looking at
the display’s centre the user should have a downward visual angle
of approximately 10°-20°.
Height: As a guide, the height (h) of your display should
approximately be as follows:
- Tall Male (Max): 560mm (22”)
- Short Male (Min): 368mm (14.5”)
- Tall Female (Max): 520mm (20.5”)
- Short Female (Min) 356mm (14”)
Distance: For visual comfort, a viewing distance (d) between
500mm (20”) to 750mm (29.5”) is recommended.
Tilt Angle: Angular adjustments to reduce reflection on your
monitor should range between 5° forward tilt to 15° backward tilt.
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 12.02.14 ©
No Allen Key necessary
Tighten
Note: Support Screen when adjusting tilt.
Loosen
Portrait/Landscape Tilt (Screen angle up/down) Pan (Screen angle left/right)
For a triple configuration Atdec recommends using:
Post Cable Cover Post Cable Cover