Atdec AWMS-2-BT75-FS User manual

AWMS-2-BT75-FS Page 1 of 4
Installation Guide
AWMS-2-BT75-FS
COMPONENT CHECKLIST
B
Bridge
(x1)
C
Leg
(x2)
A
Post
(x1)
D
Bracket
(x2)
F
4mm/6mm
Hex Key
(x1 each)
E
VESA Plate
(x2)
G
M8x30mm
Cap Screw
(x4)
J
M8x80
Cap Screw
(x2)
I
M8 Washer
(x2)
L
M4x10 Screw
(x8)
K
Post Cap
(x1)
M
M4x20 Screw
(x8)
N
10mm Spacer
(8x)
H
M8 Nut
(x4)
IMPORTANT INFORMATION
! Product should only be assembled and used as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
! EachBracketsupportsamaximumweightasperabovecapacityspecication.
! This product is not suitable for outdoor use.
! Do not use this product for mobile applications.
! Do not move stand with screens attached.
! VESA mounted accessories (such as mini PC brackets and mounts), and offset VESA locations exert additional leverage that can
exceed the capacity of the mount even though the monitor weight may be within the stated range. Please contact Atdec if you
would like further information.
! WARNING! Death or serious injury may occur if a child climbs on or tips product. Anchor product if applicable. Never place
product in an unstable location.
Freestanding HD Dual Vert
REQUIRED TOOLS
• Phillips Head Screwdriver
CAPACITY
Flat Monitor
4.5 - 25kg (10 - 55lb)
Curved Monitor
4.5 - 18kg (10 - 39lb)
Display Size
24” - 55”
300mm (12”) max overall
display depth

AWMS-2-BT75-FS Page 2 of 4
2. Attach Post to Base
2.1 Insert M8x80 Cap Screws (x2)
through M8 Washers and holes in
Base then fasten to Post.
Tightenrmly.
I
J
A
3. Slide Brackets onto Post and Set Height
3.1 Line up the inner guide
on rear of Bracket with rear
channel on Post.
Slide inner guide into channel,
then lower Bracket.
1. Assemble Base
1.1 Align Bridge holes and Leg
holes. Use 6mm Hex Key.
Hold M8 Nut in hexagonal
recess until M8x30 Cap Screw
engages. Tighten screw.
65%
A
B
G
H
1.2 Repeat on
opposite Leg.
2.2 Remove clips and covers
from post by sliding up and out
or by squeezing sides.
NOTE:
Rest short end of Bridge on a
soft surface while fastening
C
B
G
H
F
65%
A
B
G
H
NOTE:
Assemble with Cable Covers facing backwards
(Towards the small side of Base)
D
TIGHTEN
WARNING:
Never loosen knob while
display is on bracket
SQUEEZE
to release
D
I
J
A
SPACE
BETWEEN
BRACKETS
≥HEIGHT
OF SCREEN
ENSURE SCREEN
WILL CLEAR BASE
SET BRACKET FOR
COMFORTABLE
SCREEN HEIGHT
K
3.2 Firmly tighten hand knob at
chosen height.
Ensureheightissufcientfor
screen to clear base once in place.
Repeat with second bracket and t
Post Cap.

AWMS-2-BT75-FS Page 3 of 4
5. Mount Bottom Display
75mm
100mm
75mm
100mm
NOTE:
For 75mm VESA
unscrew 5mm to
access top holes E
L
TOP
4.2 Attach VESA Plate
with M4x10 Screws.
OR For recessed VESA use 10mm
Spacers and M4x20 screws.
4.1 VESA mount compatibility
5.1 Set VESA Plate to
open position.
Bottom display must be
mountedonBracketrst.
NOTE:
Use two people to install
display
4. Attach VESA Plates to Displays
E
M
N
OPEN
WARNING:
Do not loosen
hand knob once
display mounted�
5.4 Set VESA Plate to closed
position by sliding clips on
both sides inwards.
5.5 Adjust display tilt
angle by gripping edges
of screen and rolling up or
down to desired position.
OPEN
TILT KNOBS
5.6 Set Display
angle by tightening
tilt knobs.
F
OPTIONAL ADJUSTMENT - TILT FRICTION
Clockwise = More friction
Anticlockwise = Less friction
4mm Hex Key can be used to reduce tilt friction (for
light screen) or increase tilt friction (for heavy screen)
5.3 Centre VESA Plate
close to Post and slowly
lower until bar on VESA
Plate sits in saddle in
Bracket.
5.2 Place stand on the
stable surface where it will
be used.
Lift display until Vesa
Plate is above the Bracket.
CLOSED

AWMS-2-BT75-FS Page 4 of 4
7. Fine Adjustment
6. Mount Top Display
ii
iii
iv
i
LHS &
RHS
TOP &
BOTTOM
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reservestherighttoalterspecicationswithoutnotice.©20221013
6.1 Check that distance
between Brackets is
equal to or greater than
the height of the display.
Repeat Step 5 to mount
top display and set tilt
angle.
Lower
Close
Adjust angle
Set angle
i
ii
iii
iv
Unstacked Stacked
Cables can
exit from the
side of the
cable cover
PUSH
PUSH
PUSH
8. Manage Cables
8.1a Load cables into
cable clip.
8.1b Insert one side of
the cable clip into a
channel on the post,
then push in the other
side.
Load cables into
cable cover
8.2a Load
cables into
cable cover.
8.2b Clip the cable
cover back onto rear
post channels.
7.1 To correct horizontal angle
of display +/- 3 °:
Turnasingleneadjustment
knob to adjust angle of screen.
Clockwise = Higher
Anti-clockwise = Lower
7.2 To close small gap between
displays +/-6mm (1/4”):
Turnbothneadjustment
knobs - alternating sides a few
rotations at a time.
Clockwise = Higher
Anti-clockwise = Lower
ii
iii
iv
i
LHS &
RHS
TOP &
BOTTOM
FINE HEIGHT ADJUST
FINE ADJUSTMENT
KNOBS
NOTE:
Ensure clips are in
CLOSED position after
fine adjustment complete
WARNING:
Always remove screens
before moving stand