Atdec VFS-Q User manual

VFS-Q Page 1 of 4
Installation Guide
VFS-Q
Freestanding Quad Monitor Mount
COMPONENT CHECKLIST
C
Crossbar
Arms
(x2)
E
VESA
Plate
(x4)
D
Quickshift
Donut
(x4)
B
Upright
Pole
(x1)
A
Base
(x1)
L
(Optional)
Security Screw
(x4)
M
Cable Ball
(x8)
F
3/5mm
Allen Key
(x1 each)
G
M8x50mm
Screw (x1)
H
M6x25mm
Cap Screw
(x2)
I
Mounting
Screw
M4x16mm
(x16)
J
Mounting
Screw
M4x12mm
(x16)
K
Mounting
Screw
M4x10mm
(x16)
N
Cable Clip
(x4)
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! Each Quickshift Donut supports a maximum weight of 12kg (26.5lbs).
! This product supports VESA mounting hole configurations: 75x75mm and 100x100mm.
! The manufacturer accepts no responsibility for incorrect installation.
! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can
exceed the capacity of the mount even though the monitor weight may be within the stated range. Please contact
Atdec if you would like further information.
REQUIRED TOOLS
• Phillips Head Screwdriver
WEIGHT RANGE
Per Monitor
Flat Monitor
0 - 12kg
0 - 26.5lbs
Curved Monitor
0 - 6kg
0 - 13.5lbs

VFS-Q Page 2 of 4
1. Attach Upright Pole to Base
1.1 Attach the Upright Pole
to the Base as shown below.
Ensure the Cable Slot faces
towards the rear.
OPTIONAL
BOLT THROUGH &
GROMMET MOUNT
Mount can also be bolted
through work surface or
grommet hole with the Atdec
Grommet Clamp (AC-GC),
sold separately.
Cable Slot
USER
BACK
TIGHTEN
FIRMLY
Upright Pole
M8x50mm Screw
5mm Allen Key
3. Attach the VESA Plate to your monitor (Repeat steps 3 to 6 for each monitor)
NOTE: Be sure to select a screw
length that suits the monitor.
3.1 Check VESA mounting compatibility 3.2 Screw VESA Plate to back of
monitor using provided screws.
100mm
75mm
100mm 75mm
Top of
monitor
Too short Too long
OK
2. Attach Crossbar and Doughnuts
2.1 Attach Crossbar to pole. 2.2 Slide doughnuts onto crossbar.
OPEN
1
SLIDE
DOUGHNUT
ONTO
CROSSBAR
2
REPLACE
END CAP
3
CLOSE DOUGHNUT LEVER ONCE
IN PLACE ON CROSSBAR.
4
HOLD SUPPORT IN PLACE
TIGHTEN
M6x25mm Cap Screw
5mm
Allen Key
CLAMP
Cable slot to
face back

VFS-Q Page 3 of 4
Cable
Balls
Cable
Clips
4. Attach your Display to the Quickshift Donut
4.1 Hook the top of the VESA plate
onto the Quickshift Mount.
4.2 Press and hold the Release
Buttons. Gently push bottom of
VESA Plate into Quickshift Mount.
Release Buttons to lock in place.
4.3 (Optional) Insert the Security
Screw, and tighten using a
Phillips-head Screwdriver.
5. Adjust horizontal position of monitors
HOOK
Back of
Display
OPEN
LOOSEN
TIGHTEN
SLIDE
CLOSE
Release
Button
PUSH
Phillips-head Screwdriver
TIGHTEN
Security Screw
5.1 Open the lever to loosen
the Quickshift Donut.
5.2 Slide the Quickshift
Donut to desired position.
5.3 If necessary, adjust the
tension between the Donut
and the Pole using the 5mm
Allen Key supplied.
5.4 Close the lever to lock the
Quickshift Donut in place.
6. Adjust the ball joint tension 7. Cable Management
6.1 If the monitors are not holding position or are
stiff to move, adjust the tension plate by tightening
or loosening the three screws.
+-
Note: Adjust 3
screws evenly in
small increments
Note: Support the monitor while making adjustments.
3mm
Allen Key
7.1 Connect cables to your Displays, routing them down
the rear of the poles. Push the cables into the slots, using
either the Cable Balls or Cable Cilps to secure them to the
pole as shown.
Cable
Balls
Cable
Clips
Note Ensure enough slack is left in cables
to allow for movement. When the slot in
each pole cannot be used, use the supplied
Cable Clips to secure the display cables.

VFS-Q Page 4 of 4
8.1 Remove monitors
8.3 Remove crossbar from pole
8.5 Lock Doughnut onto pole
OPTIONAL 8. Switch to a triple, dual or single monitor mount
Example
8.2 Slide off doughnut
8.4 Slide Doughnut onto pole
UNLOCK
REMOVE
END CAP
SLIDE DOUGHNUT
OFF CROSSBAR
3
1
2
Slot
UNLOCK
SLIDE DOUGHNUT
ONTO POLE
(Ensure tongue in
doughnut aligns
with slot in pole)
Tongue
3
2
REMOVE
POLE CAP 1
3
PRESS AND
HOLD BUTTONS
LIFT OFF MONITOR
PULL OUT BOTTOM
OF MONITOR
2
1
SUPPORT
CROSSBAR
UN-SCREW
CROSSBAR
(Use 5mm
Allen Key)
REMOVE
CROSSBAR
FROM POLE
2
1
3
REPLACE
POLE CAP
LOCK DOUGHNUT
TO POLE
Reattach monitor
following steps 4.1 to 4.3
2
1
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20200703