Tsubaki Seamless Light Type H Installation Manual
We will appreciate for your purchase of 'Tsubaki Seamless Light Type H'. Please peruse this manual and install correctly and safely.
such as AC100 to 230V. It will cause fume or fire.
・ Excessive bending and twisting of the product.
・ Dropping and strongly striking the product.
□This product is IP67 rated:
This product should not be installed in a location where water is
continuousｌｙ splashed or underwater. GL10-96D1**K (Standard type) (** : Color temperature)
□GL10-96D1**KW ( "W" type ) (** : Color temperature)
22 25 28 30 35 40 50 RX GX BX YX
Please do not use the product in the following area.
・Area with synthetic rubbers and cardboards. DC24V
・Area with the material containing sulphur. 11 W / m ( Only Red 9 W/m )
・Area with atmosphere of sulphur such as hot springs.
-10 ~ +55℃(Indoor / Outdoor)
□If there is any trouble with the product, please immediately 60mm (6 LED) * Customized length order available If necessary, cut the AL channel in order to meet the length of the product.
turn off the power and contact the dealer or installer.
W 11(13)×H25(27) ×L mm *Note : (Size of "end parts")
□Turn off the power, before installing or handling the product.
Ambient temperatures must remain the product specification.
□Please be careful about static electricity. It will damage LED's.
□Please note that there is some variation in color among LED's.
Please be careful that eyes might be hurt when you look
straight at light emitting part.
The temperature rise of the product is influenced with the
capacity and the distance from housing.
The product is horizontal bending type. Please do not bend
the product toward vertical direction. It may cause the failure.
Please connect the lead wires with same color and use the
heat shrinkage tube.
When connecting the product in serial, please use "W" type
with Standard type *. Do not connect Standard type with
Standard type.
Electrical works certificate is required to install and inspect
this product.
It is dangerous working with wet hand. May cause electrical
shock.
Do not put screws on the products directly. It may cause
damages. Please refer to "How to Install".
Please do not perform the following actions on the product. It
will cause to decline in water resistant and installation
performance.
Input voltage is 24VDC only. Please do not apply other voltage
The product can not be used the place such as "Atmosphere
of corrosive gas and flammable gas", because it may cause
troubles.
For installing the product, please use the AL channel and the fixing spring.
Installing the AL channel with M4 screws
onto the wall.
Inserting the product into the fixing spring ,
4pcs/970mm
Flexible line installations / L=1000mm
Straight line installations / L=1000mm
Recommended total length connectable per power supply
70 ～ 5050
150 +0
-30
11
25
+2
-2
L: The product's connectable length to a power supply (m)
R: Rated wattage of a power supply (W) P: Power consumption of a product (W/m)
e.g. 100(W) x 0.7 / 11(W/m) = 6.3(m)
(100W power supply can be used for product's length 6.3m as maximum.)
As for the product's connectable length to a power supply, please refer to the following formula.
<Example> When length of the product is 970mm.
・Set the fixing spring at the 125mm position from
the product's edge
・Put the fixing spring on the every 240mm pitch
as follows.
Insert the product into the channel
except end caps.
・When total length of the products is 10.1ｍ( 5050mm ×2 ) or less, serial
connection is available.
・When total length of the products is more than 10.1ｍ( 5050mm ×2 ) , parallel
connection is required.
