Atex TL10-090AM K Series User manual

Caution when Installing the Product
Keep the followings to prevent damages, electric shock, fume and fire.
Ver.200305
ZTE2TLRGB(W)
Do not connect to AC power.
Do not pull out the product diagonally
from the channel.
Do not use a tool with sharp point .
Do not tramp on or strike the product.
Do not bend the product toward
horizontal direction.
NG!
NG!
NG!
NG! NG!
Horizontal direction
NG!
Vertical direction.
Bending radius is 30 mm or more.
✔OK

Tape Light (RGBW/RGB) Color Installation Manual
We will appreciate for your purchase of 'Tape Light RGB(W) Color'. Please peruse this manual and install correctly and safely.
□Electrical works certificate is required to install and inspect
this product.
■Product Specification ■Out looking
□Input voltage is 24VDC only. Please do not apply other voltage
such as AC100 to 230V. It will cause fume or fire.
□Please do not put screws on the products directly.
It may cause damages. Please refer to "Installation Guide"
□Please do not perform the following actions on the product.
It will cause to decline in water resistant and insulation performance.
・Excessive bending and twisting of the product.
・Dropping and strongly striking the product.
□It is dangerous working with wet hands. May cause electrical shock.
□This product is a drip-proof specification.
The product should not reside in standing water.
□The product can not be used the place such as "Atmosphere of
■Dimension
corrosive gas and flammable gas"Because it may cause troubles.
Please do not use the product in the following area.
・Area with synthetic rubbers and cardboards.
・Area with the material containing sulphur.
・Area with atmosphere of sulphur such as hot springs
□If there is any trouble with the product, please immediately turn off the
power and contact the dealer or installer.
"W" type：Lead wires at both ends.
□Please perform installation or removal, after the switch must be turned off.
■Options
□Please be careful that eyes might be hurt when you look straight
at light emitting part.
□The temperature rise of the product is influenced with the capacity
and the distance from housing. When installed, please make sure that
you have to keep the required space for installation based on ■Recommended total length connectable per power supply
"Notice of Installation".
As for the product's connectable length to a power supply,
Ambient temperatures must remain the product specification. please refer to the following formula.
※This picture is RGBW type.
□Please be careful about static electricity. It will damage LED's. L = R × 0.7 ÷ P The RGB type does not have the lead with the white identification tube.
The product is vertical bending type. L: The product's connectable length to a power supply (m)
Please do not bend the product toward horizontal direction. R: Rated wattage of a power supply (W)
It may cause the failure. P: Power consumption of a product (W/m)
□
e.g. 100(W) x 0.7 / 10(W/m) = 7.0(m)
Vertical bending (100W power supply can be used for product's length 7.0m as maximum.)
□
Horizontal bending ■Recommended DMX driver （Option）
□Let me turn on the direction of the white of this product with White LED.
As for the direction of the white by the lighting,
a white balance collapses at the R,G,B same time.
□Please note that there is some variation in color among LED's. ■Recommended DMX controllerr （Separate sale）
Please contact to our sales representative.
Ver.200305
ZTE2TLRGB(W)
Warning
Precautions
Please do not cut the product at a project site.
The water and dust resistance cannot be guaranteed.
Then the performance will be reduced.
If you need the various length for a project site,
we recommend to order the product with the customized length.
Specification
Cutting
Unit
：
mm
PC Mounting Bracket
(Option)
PC Rigid Channel (Option)
9
18
X-X'
5
15
For Keeping
X'
X
68 ～5048
240
30 30
10 10 10
10 10 10
+5
-15
+2
-2
※"W" type only
Cable color means below.
White cable ：＋24V
Red cable：Red
Green cable：Green
Blue cable：Blue
Yellow cable
：
White
（
RGBW type only
）
Product
RGB type
** 28 50
Input Voltage
Power Consumption 10 W / m
Dimension
Cutting points
Weight
Bending Radius
LED pitch
115g/m
R30mm vertical
10 mm
Environment
Exterior, IP67 rated
-10～+55℃
W 15(18)×H 5(9) ×L60(68)～5040(5048) mm Note：(Size of "end parts")
60mm (6 LED) *Customized length order available
TL10-090AM**KW
(** : White Color Temperature)
TL10-090AMW
RGB
Color Temperature
RGB
＋ W(2800K)
RGB
＋ W(5000K)
Product Name
Tape Light (RGBW/RGB) Color
RGBW type
Product No.
(Standard type)
TL10-090AM**K
(** : White Color Temperature)
TL10-090AM
DC24V ±1% *The power supply more than ±1% is unusable
15 W / m
Product No.
("W" type)
Product Name Product No. Remarks
PC Rigid Channel FJS00-22 Transparent Polycarbonate, Length=1,000mm
PC Mounting Bracket FJB00-21 Transparent Polycarbonate
Company Product No.
LIN180D3 （LINEARdrive 180D）
LIN720D3 （LINEARdrive 720D）
eldoLED

Tape Light (RGBW/RGB) Color Installation Manual
We will appreciate for your purchase of 'Tape Light RGB(W) Color'. Please peruse this manual and install correctly and safely.
Wiring Method
□
□
□Choose the power supply and DMX Driver that has eough power.
□The folowing is recommended list of total length of the lights that can be connected.
□Wire cable size effects the available length of the wire cable.
TL10-090AM**K(W) RGBW type
TL10-090AM(W) RGB type
※1Ampacity varies based on its manufacture.
※2
□Please contact our sales representative for more information of wiring.
Total length of serial connected products should be 10m (10096mm = 5048mm x 2) or less. If two or
more products are used, connect them in parallel so that the serial length does not exceed 10 m.
Cable color means below.
White cable: +24V, Red cable: Red, Green cable: Green, Blue cable: Blue, Yellow cable: White
These lengthes are assumed as the products are connected e current value calculates it in the Max
Unit Connectable. When the product length is shorter than the Max Unit Connectable, Maxwire
Length can lengthen it by a proportion calculation.
Ver.200305
ZTE2TLRGB(W)
AC LINE
(A)Dimming Contoroｌler
(B)Power Supply 24VDC
(C)DMX Driver Please select the Cable size and
length according to the table
below.
Please use the controller which
can control DMX driver.
Please select the power supply unit
according to the length of the
product.
Please wire the lead wires with
same color.
2
When the length of the product
connected to one DMX driver
exceeds 10m, please set other
DMX driver, and connect it and the
product to power supply unit in
parallel.
Please regulate the length of the
product depending on
current tolerance of DMX Driver.
1
When you wire the signal lines,
Please follow the manual of DMX
Driver.
(D)Tape Light RGBW Color
For Keeping
DMX Driver
TL10-090AM**K(W)
RGBW type
TL10-090AM(W)
RGB type
Remarks
LIN180D3 ～7516 mm ～10096 mm
LIN720D3 ～10096 mm ～10096 mm
Ampacity *1 Recommended wire length
S-VCTF0.75sq-5C
AWG 18 8.0 A 5.0 m
S-VCTF1.25sq-5C
AWG 16 11.0 A 9.0 m
S-VCTF2.0sq-5C
AWG 14 14.0 A 14.0 m
Wire cable
Ampacity *1 Recommended wire length
S-VCTF0.75sq-4C
AWG 18 8.0 A 8.0 m
S-VCTF1.25sq-4C
AWG 16 11.0 A 13.0 m
S-VCTF2.0sq-4C
AWG 14 14.0 A 20.0 m
Wire cable

Tape Light (RGBW/RGB) Color Installation Manual
We will appreciate for your purchase of 'Tape Light RGB(W) Color'. Please peruse this manual and install correctly and safely.
Installation Guide
Use of PC Rigid Channel
Use of PC Mounting Bracket
(1) Cut the Channel
Please fix the PC Mounting Bracket in the necessary location with screws.
Recommended pitch is 220mm or less
Recommended screws :4.1 Round head screw
Please increase the number of the PC Mounting Bracket
if needed for installation location at the project site.
The product is vertical bending type.
Bending Radius is 30mm vertical.
(2) Remove the burr of the channels after cutting
(1)Please useAtex PC Rigid Channel and Atex PC Mounting Bracket for Accent Tape Light to install.
(2)Please do not put screws on the products directly. It may cause damages.
(3)Please do not use a double sided tape and a glue with the products to install.
(4)Please do not bend the product forward horizontal direction. It may cause the failure.
(5)The Endcap are processed for water resistant or insulation.
Please do not constrict the product to keep the performance.
(6)Please do not perform the excessive bending or twisting of the lead wires.
It will cause the failure and the decline in water resistant performance.
Ver.200305
(4) Install the product into the Channel
①Please install the product with the diagonal line
toward groove on the channel as the right drawing.
②After that, please install the products in the channel.
Please do not constrict LED of the product when
installing the product in the channel.
When removing the products from the channel,
please reverse the procedure above.
ZTE2TLRGB(W)
Prohibitions：
Please do not remove the products from
the channel with excessive tension as the right photo.
It will cause the failure.
Note that the burr may cause damages.
* electrifications * smoke.
(3) Mount the Channel onto the wall
Please mount the PC Rigid Channel on the wall using
screws into the screw hole to properly secure it.
Screw : 4.1 Round head screw
Please cut the PC Rigid Channel as needed because it is not
available to insert the end cap of the product in the PC Rigid
Channel.
The insertion of the Endcap to the PC Rigid Channel may
cause the failure and the damage.
Please have the gap 10-20mm between the Endcap and the
PC Rigid Channel.
Endcap
PC Rigid Channel
PC Rigid Channel
①
➁
Groove on Channel
10～20mm
Caution
For Keeping
screws
PC Mounting Bracket
Less than 220mm