ATI Technologies Dimmable SunPower T5 User manual

DIMMABLE
SUNPOWER
T5 HIGH-OUTPUT FIXTURE

Getting Started
To change or modify the controller settings: Press the center button once.
Scroll through the settings menu using the top and bottom buttons.
To select the desired setting, press the center button down.
Scroll through setting options using the left, right, up and down buttons
To select the desired setting, press the center button down.
To confirm change(s), select ‘YES’ by pressing the right button.
To cancel change(s), select ‘NO’ by pressing the left button.
All settings can be accessed using the same procedure.
Required settings for each channel in automatic mode:
Each channel needs a minimum of four set points. The first set point for
each channel must always be set to ‘ON’, while the last set point must
always be set to ‘OFF.’ The last set point must not be after 23:59.
Congratulations on your new ATI Dimmable SunPower! This fixture features
exceptional performance and control that you are sure to enjoy. We know you
have choices in your aquarium lighting and we thank you for choosing ATI.
What’s included: ATI Dimmable SunPower high-output T5 fixture with built-in
controller, acrylic shield, and hanging kit
Test the fixture before installing: Remove the acrylic shield. Insert bulbs
into all available slots by sliding both ends into the socket pair. Rotate each
bulb 90º to lock it into place. The labeled end should line up over the hole in
the fixture. Plug the power cord into the outlet. The controller will light up.
Press the left, middle, and right buttons on the controller at the same time.
The fixture will now run through a testing of the fans and both T5 channels.
Installing the fixture: Remove the protective film from the acrylic shield and
slide back into the fixture. The acrylic shield should be used at all times. Use the
supplied hanging kit to hang the fixture over your aquarium. Plug in and enjoy.
For additional setup information, please review the ‘Controller Setup’ information
here, as well as the ‘Tips and Troubleshooting’ leaflet included with the fixture.
To keep the fixture in good working order, please be sure to clean and inspect
the fixture at least once a month. Prior to performing any maintenance, be
sure to turn off and unplug the fixture.
Wipe down each reflector with a soft polishing cloth to remove any moisture
build-up and/or salt spray. This will help maintain their reflective quality
and help reduce the chance of deterioration and rust. DO NOT USE ANY
CHEMICALS OR DETERGENTS on the silver-coated reflectors or any part of
the fixture, as this may damage the fixture and will void the warranty.
Check the inside of the fixture for any signs of moisture damage or salt creep.
Be sure to check locations that are typically considered dry to ensure that
moisture has not seeped in.
Inspect the end-caps for any signs of moisture damage or electrical arcing.
Clean and inspect all fans. Fixture should not be used for an extended period of
time if any fans are out, as this may cause premature ballast and bulb failure.
Clean the outside of the fixture and acrylic shield with a soft cloth or sponge.
Note: If practical, please keep all packing in the rare event the fixture needs to
be returned for service.
Maintenance
Channel 2
01) 09:30 On
02) 10:00 10%
03) 10:30 30%
04) 12:00 50-100% *
05) 14:30 40-80% *
06) 16:30 30%
07) 17:00 10%
08) 17:30 Off
09) 00:00 ---%
10) 00:00 ---%
Controller Setup
Controller Recommended Settings
First 50+ Hours
Bulb Break-in Period
Channels 1 & 2
01) 08:00 On
02) 08:01 100%
03) 20:30 100%
04) 20:30 Off
05) 00:00 ---%
06) 00:00 ---%
07) 00:00 ---%
08) 00:00 ---%
09) 00:00 ---%
10) 00:00 ---%
After First 50+ Hours (Optional Example)
Normal Settings
Channel 1
01) 09:00 On
02) 09:30 10%
03) 10:00 20%
04) 12:00 40-100% *
05) 15:00 30-80% *
06) 17:00 20%
07) 17:30 10%
08) 18:00 Off
09) 00:00 ---%
10) 00:00 ---%
* This value can be slowly adjusted up as your corals acclimate to the new light. It
typically takes several days to several weeks for corals to adjust to a change in the
intensity of the lights. If you have too much light, we recommend reducing your
intensity, reducing the length of your photo period and/or raising the fixture up.
Note: Controller uses 24-hour time clock.
For additional information, including detailed installation and how-to videos, please visit www.atinorthamerica.com