Atlantic Furniture CAPTAIN’S BED HEADBOARD User manual

ASSEMBLY INSTRUCTIONSASSEMBLY INSTRUCTIONS
( TWIN, FULL )( TWIN, FULL )
Before assembling your Captain’s Bed Headboard, please read through these
instructions carefully, familiarising yourself with the different parts.
Please note that you will require a Phillips Head Screwdriver and an Allen wrench.
Page1of4
Captain’s Bed Headboard 10072008
READY
Assembling by Adult
Phillips Head
Screwdriver
Customer Supplied
D
B
A
C
E
F
G
METAL L BRACKET - 6 pcs
HEADBOARD HARDWARE
JCB M6 X 35mm - 8 pcs
WOODEN DOWEL 10 X 30mm - 12 pcs
JCB M6 X 15mm - 24 pcs
WOODEN PULL - 2 pcs
PULL SCREW - 2 pcs
ALLEN WRENCH-1pc
CAPTAIN’S BED HEADBOARD
CAPTAIN’S BED WITH STORAGE TRUNDLE
CAPTAIN’S BED WITH UNDER BED CHEST

HEADBOARD
PARTS LIST
01
02
03
04
05
06
07
08
09
HARDWARE 1 BOX
1 SET
1PC
1PC
1PC
1PC
1PC
1PC
2 PCS
TOP STORAGE
LEFT SIDE PANEL
RIGHT SIDE PANEL
LOWER SHELF
FRONT PANEL
PILLOW STOP
BACK PANEL
MOUNTING BLOCK
01
02
03
04
08
05
06
07
09
09
STEP 1
STEP 1 STEP 2
STEP 2
03
A
A
A
A
A
A
Insert Wooden Dowels (A), into the
receiving holes in top edge of Side
Panels (03)(04) as shown.
Insert Wooden Dowels (A), into the
receiving holes in both ends of Lower
shelf (05) as shown. Install metal L
brackets (D) to the Lower Shelf (05),
using JCB (C). Tighten with Allen
wrench (G).
Locator hole will
receive (A)
Locator hole will
receive (A)
Bottom View
A
A
G
05
D
D
D
D
C
C
C
C
C
Page2of4
Captain’s Bed Headboard 10072008

STEP 3
STEP 5
STEP 4
Insert Wooden Dowel (A), into the
receiving hole in each end of Pillow
stop (07) as shown. Install metal L
brackets (D) to the Pillow stop (07),
using JCB (C). Tighten with Allen
wrench (G).
G
A
A
A
D
D
C
C
07
Locator hole will
receive (A)
Bottom View
Insert Wooden Dowel (A), into
the receiving hole in each
Spacer Block (09) as shown.
09
Attach the lower shelf (05), front panel (06), pillow stop (07) & back panel (08)
to side panels (03)(04) as shown. Using JCB (C), tighten with Allen wrench (G).
( Taking care to lay it on some cardboard to prevent scratching ).
( BACK VIEW )
04
06
07
03
G
CC
C
C
C
ZOOM IN
Page3of4
Captain’s Bed Headboard
STEP 3
STEP 5
C
05
08
10072008

STEP 6
STEP 7
STEP 8
Lay the top storage (02) on the floor upside
down, taking care to lay it on some cardboard
to prevent scratching. Stand the side panel
assembly upside down and using JCB (B) ,
tighten with Allen wrench (G).
Install wooden pull (E) to each of the
doors as shown. Using pull screws (F),
tighten with Phillips head screwdriver.
Install mounting blocks (09) to each side of
captain’s bed as shown. Using JCB (B),
tighten with Allen wrench (G)
If attaching the Headboard to
a Metal Frame you must attach
mounting blocks as shown below.
02
B
B
B
B
B
G
H
B
F
UPSIDE DOWN
G
DOOR OPEN
POSITION
Congratulations !
Your Captain’s Bed Headboard is now ready for use.
We recommend that you recheck that all screws are tightened,
and that all parts are secure before use and periodically to ensure safety.
Page4of4
Captain’s Bed Headboard
09
09
10072008