Atlantic Furniture WOODLAND BUNK BED TWIN-TWIN User manual

Size of Mattress and Foundation
The length and width of the upper bunk mattress and foundation are as follows :
Width
37 ½”- 38 ½”
Length
74”- 75”
Thickness
9 ½” max
You must use only this size mattress.
Ensure thickness of mattress and foundation combined does not exceed 9 ½”
and that the mattress is at least 5” below upper edge of guardrails.
This Bunk Bed uses a slat kit for mattress foundation.
Replacement Parts
Replacement parts, including additional guardrails, may be obtained from any
Atlantic Furniture dealer
SAFETY WARNINGS
! !
( 1 )
( 2 )
( 3 )
( 4 )
( 5 )
( 6 )
( 7 )
( 8 )
( 9 )
(10)
(11)
(12)
(13)
(14)
Follow the information on the warnings appearing on the upper bunk end structure
and on the carton. Do not remove warning label from bed.
Always use the recommended size mattress or mattress support, or both,
to help prevent the likehood of entrapment or falls.
Surface of mattress must be at least 5 in. (127mm) below the upper edge of guardrails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other component are
in their proper position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed, and prohibit jumping on the bed.
Always use ladder for entering or leaving upper bunk.
Do not use substitute parts. Contact the manufacturer for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed
next to a wall, the guardrail that runs the full length of the bed must be placed
against the wall to prevent entrapment between the bed and the wall.
The use of water or sleep flotation mattress is prohibited.
Prohibit more than one person on upper bunk.
STRANGULATION HAZARD : Never attach or hang items to any part of the Bunk Bed
that are not designed for use with the bed: for example, but not limited to, hooks, belts
and jump ropes.
Keep these instructions for future reference.
Page 1 of 8
BUNK SAFETY WARNING

READY
ASSEMBLY INSTRUCTIONS
HARDWARE
Adult Assembly
Allen wrench
Phillips Head
Customer Supplied
Screwdriver
Before assembling your Woodland bunk bed, please read through these
Thank you for choosing our new bunk bed.
This practical design offers the utmost in versatility.
TWIN - TWIN
instructions carefully, familiarize yourself with the different parts.
Please note that you will require a Phillips head screwdriver and an Allen wrench.
WOODLAND BUNK BED
BUNK BED SHOWN WITH LADDER
WOODLAND BUNK BED TWIN-TWIN Page 2 of 8
AJCB M6 X 3 1/8” - 16 pcs
Spare - 2 pcs
B
D
E
F
C
Barrel Nut - 16 pcs
Allen Screw M6 X 2" - 4 pcs
Wood Screw 1" - 4 pcs
Wood Screw 5/8" - 4 pcs
Wooden Dowel - 8 pcs
Spare - 2 pcs
Spare - 1 pc
Spare - 1 pc
Spare - 1 pc
Spare - 2 pcs
Metal Pins - 4 pcs
E
E
IAllen wrench - 1 pc
Spare - 1 pc
H
G
Wood Buttons - 4 pcs
NOTE : WE INCLUDE SPARE HARDWARE IN CASE THE ALLEN WRENCH, ALLEN SCREW, JCB, BARREL NUT
WOODEN DOWEL OR WOOD SCREW ARE DAMAGED DURING ASSEMBLY.
GUARDRAIL CAN BE SET UP AT EITHER
END OF THE BUNK BED

PARTS LIST
01
02
03
04
05
06
07
08
09
10
HARDWARE
UPPER PANEL 1 BOX
1 BOX
1 BOX
LOWER PANEL
FULL GUARDRAIL
3/4 GUARDRAIL
LEFT END CAPS
RIGHT END CAPS
LONG RAILS
CLIP ON LADDER
TWIN SLAT KIT
01
02
03
04
07
08
08
10
10
08
08
07
06
06
05
02
03
Page 3 of 8
1 BOX
1 BOX 2 SET
09
WOODLAND BUNK BED TWIN-TWIN

STEP
STEP
08
02
02
A
B
B
Attach the long rails (08) to the upper panels (02), using JCB M6 X 3 1/8” (A) and barrel nut (B).
Tighten with the Allen wrench (I).
Insert wooden dowel (C) to the locator holes will receive (C) as shown below. Attach the full guard rail (04)
to the left, right end caps (06)(07), using Allen screw (D),Tighten with the Allen wrench (I).
Repeat for 3/4 guard rail (05).
08
Adult Assembly
A
B
I
JCB M6 X 3 1/8”
Barrel Nut
Allen wrench
Page 4 of 8
If the bunk bed will be placed next to a wall, the guard rail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and the wall.
A
A
B
B
07
06
06
07
04
05
D
D
D
CC
D
1
2
D
C
Adult Assembly
JCB M6 X 2 ”
Wooden Dowel
I
Allen wrench
A
WOODLAND BUNK BED TWIN-TWIN

Install the full and 3/4 guard rail assemblies onto the long rails, and fix in place using wood screws (E).
Tighten with the Phillips head screwdriver.( Customer Supplied )
Adult Assembly
1 “ Wood Screw
Phillips head
Customer Supplied
screwdriver
Adult Assembly
Phillips head
Customer Supplied
screwdriver
E
Page 5 of 8
Lay the twin slat kit (10) onto the bed. Fix in place using wood screws provided in the slat kit box.
FOR SLAT KIT ASSEMBLY follow assembly instructions included with slat kit.
STEP 3
10
STEP 4
E
E
EE
FULL GUARD RAIL
ASSEMBLY
3/4 GUARD RAIL
ASSEMBLY
GUARDRAIL CAN BE SET UP AT EITHER
END OF THE BUNK BED
WOODLAND BUNK BED TWIN-TWIN

Adult Assembly
A
B
I
JCB M6 X 3 1/8”
Barrel Nut
Allen wrench
Attach the long rails (08) to the lower panel (03), using JCB M6 X 3 1/8” (A), and barrel nut (B).
Tighten with the Allen wrench (I).
Adult Assembly
Phillips head
Customer Supplied
screwdriver
Page 6 of 8
STEP 5
A
A
B
B
B
B
A
A
STEP 6
10
Lay the twin slat kit (10) onto the bed. Fix in place using wood screws provided in the slat kit box.
FOR SLAT KIT ASSEMBLY follow assembly instructions included with slat kit.
08
08
03
03
WOODLAND BUNK BED TWIN-TWIN

Adult Assembly
Metal Pins
G
Insert metal pins (G) into the holes in top of the lower panels. Lift the upper panels onto the lower
panels as shown, and fit the metal pins into the holes in the bottom of the upper panel legs.
This step requires
two strong people.
This step requires
two strong people.
CAUTION
!
Congratulations !
LOWER
Your Woodland bunk bed is now ready for use.
We recommend that you recheck that all screws are tight,
and that all parts are secure before use. Periodically to ensure lasting Safety.
Wood Screw 5/8"
Adult Assembly
Phillips head
Customer Supplied
screwdriver
Lastly, install Clip on Ladder (09). Using wood screw (F) tighten with Philips head Screwdriver.
Page 7 of 8
STEP 7
STEP 8
09
G
F
F
F
F
F
F
G
G
G
F
UPPER
WOODLAND BUNK BED TWIN-TWIN

Disassemble upper bunk by removing guard rails. Also remove metal pin from lower bunk.
Disassemble upper bunk by removing upper panel (02) and lower bunk by removing lower panel(03).
Exchange upper panel to the lower panel position and Install hardware tighten with Allen wrench.
UPPER BUNK LOWER BUNK
CONVERSION TO 2 TWIN BEDS.
TWO TWIN BEDS
Use Wood button (H) to cover holes as shown below.
Page 8 of 8
UPPER BUNK LOWER BUNK
02
03
Metal Pin
H H
H H
Adult Assembly Wood Button
H
WOODLAND BUNK BED TWIN-TWIN