Atleisure 1900675 User manual

11ft Offset Umbrella
Crank Rope
Replacement and Operation Manual
Step 1: Place the umbrella frame with canopy on a soft, clean surace to
prevent damage during the replacement process.
1
Item: 1900675, 1237133, 1900766, 9636963
Step 2: Take the cap off of
the long arm.
Step 3: Remove the bolt with
the hex key.
Step 4: Pull apart the velcro on the under side of the canopy.

2
Step 5: Remove the solar panel, then pull the rib out of the
canopy pocket.
Step 6: Remove the cover
underneath the lower rib holder.
Step 7: Remove the `cap
from the cover.
Step 8: Untie the knot. Step 9: Remove the cap
covering the bolts attaching
the pole and the long main arm.

3
Step 10: Remove the bolts attaching the pole and long main arm.
Please note you must use the hex key to hold the bolts tight on one
side while removing with the wrench on the other.
Step 11: Use the hex key to
remove the bolts attaching the
crank and the long main arm.
Step 12: Squeeze the glide
handle and slide the handle all
the way off of the pole.
NOTE: Please make sure that you keep all necessary parts from
disassembling the arm. Please hold on especially to the plastic
connector ring from the long main arm and note that the rope
must go through the pulley on reassembly.

4
Step 14: Assemble the new glide handle with the crank and
the plastic connector. Please note that there is another pulley
inside of the plastic connector. The glide handle, crank, bolts, and
rope must be connected as shown above to function properly.
Step 15: Insert the bolts. Secure
one bolt while attaching the
other with the hex key.
Hold bolt in place
Step 16: Squeeze the glide handle
and slide upwards to the middle
of the umbrella pole.
Step 17: Insert a steel wire hook (like a wire hanger) into the top of the
long arm from the top of the rib holder. It must go through on top
of the pulley.

5
Step 18: After the hook is inserted, hook it through the rope (which
should be through the glide handle) and pull the rope through with
the hook.
Step 19: After the rope is pulled through, ensure that the rope is
on top of the pulley, as well as in the pulley groove.
Step 20: Connect the glide handle and the long arm with bolts.
Secure one bolt while attaching other with hex key. Place caps
over the bolts.
Hold bolt in place

6
Step 21: Make sure that the rope is going through as shown.
Step 22: Use the steel wire hook to pull the rope out of the hole
on the upper pole holder.
Step 23: Take the cover off
of the rib holder support bar.
Step 24: Pull the rope out of the
upper rib holder, then through the
rib holder support bar. The rope
must go through the pulley inside
the upper rib holder and
pulley groove.

7
Step 25: After the rope has gone through the rib holder support bar, put
the cover back onto the rib holder support bar.
Step 26: Insert the rope through the lower rib holder, then through
the cap, then put the cap back into the lower rib holder. Put the rope
through the nut, then tie a knot, as shown above.
Step 27: Insert the knot into the smaller cap, then put the smaller cap
back into the lower rib holder.

8
Step 29: Fasten velcro back together on the long arm and then screw
in the bolt with the hex key. Place the cap back onto the bolt.
Step 30: Put the rib into the pockets on the canopy
to complete reassembly.
Step 28: Put the canopy back onto the frame as shown above,
making sure that the canpy hole is placed correctly over the rib holder.
Screw on the solar panel.

ATLeisure, LLC
1040 Boulevard SE, Suite B
Atlanta, Georgia 30312, USA
Customer Service Toll Free 1-855-880-7205
8am - 5pm Eastern Time, Monday through Friday
www.atleisure.com