Atleisure SL-SW5217 Installation guide

Two Person Swing
Assembly & Care Instructions
IMPORTANT : RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
Toll Free: 1-855-880-7205 (English is offered)
8am - 5pm, Monday through Friday, Eastern Standard Time
DO NOT RETURN TO STORE
For outdoor domestic use only. Not for commercial use.
Designed in USA
Made in China
For assistance with assembly, parts, or customer service, please contact:
SKU: 9022334
Model: SL-SW5217

2
Contents
Package Contents
Package Contents
Assembly and Use
Care and Maintenance
Warning and Cautions
2-3
4-7
8
8
Warranty 8
Replacement Parts 9
Please lay out all parts prior to assembly to make sure all parts are present.
Needs two adults to assemble.
Hardware Contents:
M
M
M6 x 86mm Bolt 4
N
N
M6 x 68mm Bolt 4
O
O
M6 x 52mm bolt 4
P
P
M8 x 50mm bolt 4
Q
Q
M6 x 45mm bolt 4
R
R
M8 x 40mm bolt 4
S
S
Screw Nut M6 12
T
T
M6 Metal Washer & M8 Metal Washer 16 & 8
U
U
M6 Plastic Cap 12
V
V
Plastic Washer 8
W
W
Hex Key 2
X
X
Wrench 1
Part Description Quantity

A
A
Top Connect Bar 1
B
B
Front Leg 2
C
C
Back Leg 2
D
D
Front and Back Leg Connect Bar 2
E
E
Back Leg Connect Bar 1
F
F
Armrest 2
G
G
Seat 1
H
H
Back 1
I
I
Hang Bar 4
J
J
Spring Hook 2
K
K
Canopy 1
L
L
Screw Knobs 2
Y
Y
Magazine Bag 2
3
Package Contents:
Package Contents
Part Description Quantity

Step 1: Align the hole of the front (B) and back (C) leg with the top connect
4
Assembly
bar (A). Then use the hex key (W) to screw the head of M6 x 86mm bolt (M).
Use the wrench (X) to screw the M6 screw nut (S) over the metal washer (T)
on the other side. Do not over tighten. Then cover the plastic cap (U)
with the screw nut (S).
Step 2: Use the hex key (W) to screw the head of M6 x 52 mm bolt (O) through
the hole offFront and back leg connect bar (D) and legs. Use the wrench (X)
to screw the M6 screw nut (S) over the metal washer (T) on the other side.
Do not over tighten. Then cover the plastic cap (U) on the screw nut (S).

5
Step 3: Use the hex key (W) to screw the head of M6 x 68 mm bolt (N) through
Assembly
the hole of back leg connect bar (E) and back (C) legs. Use the wrench (X)
to screw the M6 screw nut (S) over the metal washer (T) on the other side.
Do not over tighten. Then cover the plastic cap (U) on the screw nut (S).
Step 4: Use the hex key (W) to screw the M8 x 50 mm bolt (P) through M8 metal
washer (T) to connect the armrest (F) and seat (G). Do not over tighten.

Step 5: Use the hex key (W) to screw the M6 x 45 mm bolt (Q) through metal
Assembly
washer (T) and the plastic washer (V) to connect the back (H) and the armrest (F).
The plastic washer (V) between the back (H) and the armrest (F).
Do not over tighten.
Step 6: Use the hex key (W) to screw the M8 x 40 mm bolt (R) through M8
metal washer (T) and plastic washer (V) to connect the armrest (F) and
hang bar (I). The plastic washer (V) between the hang bar (I) and the armrest (F).
Do not over tighten.
6

7
Step 7: Hang the seat (G) and back (H) on the top connect bar (A)
Assembly
through the spring hook (J).
Step 8: Cover the canopy (K) on the top connect bar (A) by screwing the
screw knobs (L). Hang the magazine bags (Y) on the armrest (F). Place the
swing on flat ground. It is now ready for use.

8
Care and Maintenance
Warnings and Cautions
DANGER : Keep children out of the assembly area during assembly.
WARNING: Read the entire instructions before beginning and follow the
steps outlined. Failure to assemble and install as instructed could result in
the swing tipping over, causing personal injury and/or property damage.
CAUTION: Assemble and use on flat surfaces. Keep away
from glass tabletops during windy conditions to prevent breakage.
INFORMATION: Schematics in this manual are for assembly and operation
illustration only. They may differ from the umbrella’s actual appearance.
Warranty
-Use mild soap and warm water to clean the frames.
-Rinse with clean water and dry thoroughly
-Be sure to drain any water accumulated inside the frames. To thoroughly
drain frames, remove foot caps and tilt frames, if necessary, to remove all
water. Water allowed to accumulate inside the frames and then exposed to
sub-freezing temperatures can cause damage to frame tubing. Such damage
is not covered under warranty.
-Any rust spots should be lightly sanded and treated with rust inhibitor and
followed with an application of touch-up paint (not included).
ONE YEAR WARRANTY
This product is covered under a manufacturer’s one year warranty from date of
purchase against defects in materials and workmanship. This warranty does not
cover damage due to neglect, abuse or weather related damage. For full warranty
disclosure, email us at customerser[email protected], call toll free at 1-855-880-
7205 or send mail to: 1040 Boulevard SE Ste. B, Atlanta GA 30312
NOT COVERED UNDER WARRANTY
This Warranty excludes the following: general frame rusting; glass breakage; acts of
nature (i.e. wind, fire, or freeze); damage caused by improper assembly, accident,
disaster, misuse, abuse, negligence and commercial use; discoloration or fading of
the finish or fabric as a result of exposure to the elements.
HOW TO FILE A CLAIM
If you are within your warranty you must have your receipt and pictures of your in-
formation to send to ATLeisure at customerser[email protected], or send by mail
to 1040 Boulevard SE Ste. B, Atlanta GA 30312. This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state.

9
Replacement Parts
For replacement parts, call our customer service department at:
1-855-880-7205, 8am - 5pm EST, Monday - Friday.
ATLeisure, LLC
1040 Boulevard SE, Suite B
Atlanta, Georgia 30312, USA
Customer Service Toll Free 1-855-880-7205
8am - 5pm Eastern Time, Monday through Friday
www.atleisure.com
A Top Connect Bar SL-SW5217-TCB
SL-SW5217-FL
SL-SW5217-BL
SL-SW5217-FBLCB
SL-SW5217-BLCB
SL-SW5217-ARM
SL-SW5217-SEAT
SL-SW5217-BACK
SL-SW5217-HB
SL-SW5217-SPRING
SL-SW5217-KNOB
SL-SW5217-MAG
1
BFront Leg 2
C Back Leg 2
DFront and Back Leg Connect Bar 2
E Back Leg Connect Bar 1
FArmrest 2
G Seat 1
HBack 1
IHang Bar 4
J Spring Hook 2
L Screw Knobs 2
YMagazine Bag 2
SL-SW5217-HDW-KIT
KIT Hardware Kit 1
Part Description Quantity Re-Order Number