Atleisure Seasons Sentry UMB-955258 Series Guide

E
ITM. / ART. 1900783, 1237211
Model: # UMB-955258
Assembly, Care & Use Manual
3.04 M / 10 FT Solar LED
Cantilever Umbrella with
Base
IMPORTANT: RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
ATLeisure, LLC
US Toll Free 1-855-880-7205 (English)
Canada Toll Free 1-888-692-1033 (French)
8:00am - 5:00pm, Monday through Friday, Eastern Standard Time
www.atleisure.com · Email: [e-mail]
DO NOT RETURN TO STORE
For outdoor domestic use only. Not for commercial use.
Designed in USA
Made in China
For assistance with use, parts, or customer service, please contact:

2E
C
GG
F
HH
D
N
E
A
B
L
JJ
M
G1
N1
CAN
G
E2
Contents
Preparation ....................................2
Tools Required for Assembly (not included) ...........3
Hardware and Package Contents....................3
Assembly Instructions .......................... 4-6
Operation Instructions .......................... 6-8
Lighting Operation & Battery Replacement ............9
Battery Disposal...............................10
Care and Maintenance...........................10
Warning and Cautions ...........................10
Warranty .....................................11
Filing a Claim..................................11
Replacement Parts .............................12
Preparation
Before beginning product assembly, make sure all contents are present. Lay out all parts
on a clean, at surface. Compare parts with package contents list and diagram above. If
any part is missing or damaged, do not attempt to assemble product or return to place of
purchase. Contact our customer service toll free at 1-855-880-7205 (English) or 1-888-
692-1033 (French) for replacement parts or further instructions.
Estimated Assembly Time: 40 minutes
Tools Required for Assembly: Open-end wrench or adjustable wrench (not included)
K

3E
Part Description Quantity
A Blow Molded Base Outside 2
B Blow Molded Base Inside 2
C Lower Cross Leg 1
CAN Canopy (on the umbrella frame) 1
D Upper Cross Leg 1
E360˚Crank Handle 1
E2 Canopy Crank Handle 1
F Holder Pole 1
G Battery 2
G1 Power Supply 1
K Pole Sleeve Collar 1
L Pole Support Cap 1
M Blow Molded Base Cap 4
N Umbrella Frame (with canopy) 1
N1 Solar Panel 1
Package Contents
Picture Description Quantity
Adjustable Wrench 1
Tools Required for Assembly (not included)
Hardware Contents
Part Picture Description Quantity
GG Outer Hex Bolt M10-1.5x20 A2-70 4
HH Flat Washer M10 A2-70 4
JJ Inner Hex Bolt M8 A2-70 2
KK Inner Hexagon Wrench M8 1

4
Step 3: Fill each base (A & B) with sand, cover with cap (M). Place pole support cup (L)
onto holder pole (F) and lay on top of blow molded base (B).
Step 1: Place lower cross leg (C) on
ground, line up notches and place upper
cross leg (D) over lower cross leg (C).
Assembly Instructions
Step 2: Attach holder pole (F) to base by
using bolts (GG) and washers (HH) (found
in blister pack). Be careful not to over
tighten. Adjust holder pole (F) to be sure
it is positioned correctly on base. Finally,
tighten with adjustabe wrench or open-
end wrench (not included).
CAUTION: Do not use sharp tools or equipment such as a knife or scissors when
removing the protective material, as it may damage the product. Be careful not to
throw away small parts such as bolts, washers, etc. that may be wrapped in the
protective materials.
E
D
C
F
HH GG
D
C
WARNING: Before opening umbrella, complete assembly as instructed in
manual. Fill each section of base with sand. Add WATER to wet the sand and
continue to fill each section with water up to top. Cover hole with cap. It is
recommended at least 91 kg (200 lbs) of weight be placed on cross legs to
ensure stability. Failure to do so will result in a weight imbalance and cause
umbrella to tip, causing damage and/or personal injury.
M
A
L
B
F
91 kg / 200 lbs
Sand (4 bags)
22.75 kg
50lbs 22.75 kg 50lbs
22.75 kg
50lbs
22.75 kg
50lbs

5
Assembly Instructions (cont.)
Step 4: Insert plug into socket under solar panel as shown above.
E
N1
Step 5. Put solar panel on top of umbrella and hide the plug and wire inside the
cavity at top. Then turn the solar panel clockwise. Do not over tighten.
Step 6: Remove battery (G) from accessories kit and place into the housing locat-
ed on the arm of the glide handle. Then put the solar umbrella in direct sunlight
outdoors to charge the solar panel for 8 hours before the first use.
MAKE SURE THE LED LIGHTS ARE OFF ON UMBRELLA TO ALLOW SOLAR PANEL
TO FULLY CHARGE BATTERY.
G

6E
Assembly Instructions (cont.)
Step 7: Insert Umbrella Frame with Canopy (N) onto Holder Pole (F). At the same time,
slide holder pole collar onto holder pole. Tighten two Hex Bolts (JJ) into holder pole to
secure the umbrella using the hexagon wrench. Attach canopy crank handle (E2) onto
glide handle and 360˚crank handle (E) to pole.
E
CAUTION: An additional person is suggested to assist with inserting the
umbrella into the pole holder.
Operation Instructions
Step 1: Unfasten storage straps around canopy and pole.
Step 2: To open umbrella, squeeze glide handle and grip together and slide up or down
pole to achieve desired tilting angle. Release grip to lock into place. To open canopy,
turn crank handle clockwise until canopy is fully open as pictured.
Close
Open
Crank
Glide Handle
Canopy open
Grip
F
N
N
FJJ E2
E
E2
E

7E
Operation Instructions (cont.)
Step 3: The canopy can be rotated 360˚. To rotate umbrella, insert crank handle (E)
onto holder pole (F) and turn the crank handle to the desired position.
Example of Canopy
Movement Using
360˚Rotation
E
F
360°„
L ever clamp
Open
Close
Glide Handle
Grip
Crank
Canopy Close
Step 4: To close umbrella, turn crank handle counter-clockwise until canopy is fully
closed. Squeeze glide handle and grip together, then slide it down pole and release grip
to lock it in place. Fasten storage straps around canopy and pole.

8E
Step 5: To rotate canopy left and right, pull on handle unlocking mechanism and turn to
desired angle. Then, put handle back in locked position to secure.
Operation Instructions (cont.)

9
Power supply port for battery
Battery power meter
Battery power meter button
LED lights button (hub lights & rib lights
Power supply included
Input: 100-240V AC
Output: 5v DC
G1
E
Lighting Operation & Battery Replacement (cont.)
Step 2: Press light button to turn solar lights on and off. Press once to turn on rib
lights on and off. Press a second time to turn on hub light. Press a third time to turn on
both ribs and hub lights. Press a fourth time to turn off all lights. Umbrella is equipped
with 2 batteries. Remove battery from hub when the battery has drained. Replace bat-
tery once fully charged. When solar energy is insufcient, you can use the power supply
indoors to charge the battery. Charge level can be seen on battery power meter lights.
INFORMATION: Battery is meant to be charged indoors. Leaving battery outside in
inclement weather will damage battery and power supply.
Battery charged after 3-4 hours using power supply or 6-8 hours of direct sunlight.
Battery life 6-8 hours when fully charged. Power supply is for indoor use only. Do not use
outdoors.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
CAUTION: YOU MUST CHARGE THE BATTERY BEFORE FIRST USE. Please note that battery
can lose charge if left unused or uncharged for a long period of time. Failure to charge the
battery will result in premature dimming of the lights in your new solar umbrella. Make sure
the light switch is in the off position when charging the solar panel. For everyday normal use,
turn light switch on at night when you want to use solar light and turn off switch after use.
MAKE SURE LIGHT SWITCH IS IN OFF POSITION DURING DAYTIME TO ALLOW THE SOLAR
PANEL TO CHARGE BATTERY.

10 E
Care and Maintenance
See the enclosed Sunbrella® care and cleaning label sewn into interior side of canopy.
Warning and Cautions
INFORMATION: Be sure to secure and/or weight the base of the umbrella.
INFORMATION: Close the umbrella and use the canopy storage straps when umbrella
is not in use. If the umbrella is stored off season in a box, the solar panel and battery pack
must be removed to avoid damage.
INFORMATION: Schematics in this manual are for assembly and operation illustration
only. They may differ from the umbrella’s actual appearance.
DANGER: Keep children out of the assembly area during assembly.
CAUTION: Assemble and use umbrella on at ground.
WARNING: Read all instructions before beginning and follow the steps outlined.
Failure to assemble and install as instructed could result in the umbrella tipping over
causing personal injury and/or property damage.
WARNING: Do not open umbrella in windy conditions, as it could be blown over and
cause personal injury or damage. To secure umbrella properly, either bolt it directly to
your deck or patio, or use a properly weighted umbrella base. Keep umbrella away from
glass tabletops during windy conditions to prevent breakage. Warranty does not cover
damage due to neglect, abuse or poor weather conditions.
CAUTION: Place the base in the desired location for use before filling. Once the base
is full, it will be harder to move
CAUTION: Before opening umbrella, insert the plug into the socket under the solar
panel. Put the solar panel at the top of umbrella and hide the plug and wire inside the
groove at the top of the umbrella. Then turn the solar panel clockwise. Do not over
tighten.
CAUTION: If leaving base out in winter months, it is recommended to add anti-freeze
to help prevent damage. When possible, bring umbrella indoors during the off season.
Battery Disposal
• Battery should be recycled or disposed of as per state and local guidelines.
• Do not open battery or try to replace battery by yourself.
• Do not dispose of batteries in re.
• Keep battery (batteries) out of reach of children

11
Made in China
E
Warranty
This product is covered under a manufacturer’s 2-year warranty from date of purchase
against defects in materials and workmanship. This warranty does not cover damage
due to neglect, abuse or weather related damage. For full warranty disclosure, email
us at customerser[email protected], call toll free at 1-855-880-7205 (English) or
1-888-692-1033 (French) or send mail to:
Atleisure, LLC
Customer Service Dept.
1040 Boulevard SE Ste. B
Atlanta GA 30312.
NOT COVERED UNDER WARRANTY
This warranty excludes the following: acts of nature (i.e. wind, re or freezing);
damage caused by improper assembly, accident, disaster, misuse, abuse, or negli-
gence and discoloration or fading of the nish as a result of exposure to the elements.
Product not intended for commercial use. This warranty gives you specic rights, and
you may also have other rights which may vary from state to state.
AUSTRALIA: Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a major fail-
ure and compensation for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods fail to be of accept-
able quality and the failure does not amount to a major failure.
If you are within your warranty, you may le a claim by sending your receipt and
pictures of your damaged umbrella and send to ATLeisure at:
[e-mail]
or by mail to:
ATLeisure, LLC
Customer Service Dept.
1040 Boulevard SE Ste. B
Atlanta GA 30312
Filing a Claim

12
Replacement Parts
For replacement parts, call our customer service department at 1-855-880-7205,
8:00am-5:00pm., EST, Monday-Friday.
E
U.S. Patent No. 5,937,882, U.S. Patent No. 8,104,492, U.S. Patent No. 6,612,713, U.S.
Patent No. 7,753,546, U.S. Patent No. 8,069,868, U.S. Patent No. 8,375,966, U.S.
Patent No. 8,727,555, U.S. Patent No. 8,794,781
D
GG
HH
C
J
JJ
E
L
A
B
L
M
G
G1
CAN
N1
N2
F
Part Description Quantity Re-order No.
A Blow Molded Base Outside 2 BSE-ABMP-11-BWN-T-C2
B Blow Molded Base Inside 2 BSE-BBMP-11-BWN-T-C2
C Lower Cross Leg 1 CSL-C78RX-BWN-T-C2
CAN Canopy 1 CAN-1108RBS-T-T2-C2
CAN-1108RBS-T-N2-C2
CAN-1108RBS-T-R2-C2
D Upper Cross Leg 1 CSL-D78RX-BWN-T-C2
E360˚Crank Handle 1 CRK-E78RHP-BWN-T-C2
F Holder Pole 1 HDP-F78RX-BWN-T-C2
GBattery 2 SOL-G-RBP-11-T-C2
GG Bolts 4 HDW-JJ-T
G1 Power Supply 1 SOL-G1-CC-11-T-C2
HH Washers 4 HDW-GG-11-T
JJ Hex Bolts 2 HDW-HH-11-T
KPole Sleeve Collar 1 HDP-SLV-F78RX-BWN-T-C2
L Pole Support Cap 1 PSC-L78R-BWN-T-C2
M Blow Molded Base Cap 4 BSE-CAP-11-BWN-T-C2
N1 Solar Panel 1 SOL-P11-T-C2
N2 Canopy Crank 1 CRK-778RG-BWN-T-NS-C2
K

www.atleisure.com · Email: [email protected]
ATLANTA, GEORGIA, USA
US Toll Free 1-855-880-7205 (English)
Canada Toll Free 1-888-692-1033 (French)
8:00am-5:00pm, Monday to Friday, Eastern Standard Time
Distributed by :
Costco Wholesale Iceland ehf.
Kauptún 3-7, 201 Gardabaer
Iceland
www.costco.is
Distribué par :
Costco France
1 avenue de Bréhat
91140 Villebon-sur-Yvette
France
01 80 45 01 10
www.costco.fr
Importado por :
Costco Wholesale Spain S.L.U.
Polígono Empresarial Los Gavilanes
C/ Agustín de Betancourt, 17
28906 Getafe (Madrid) España
NIF: B86509460
900 111 155
www.costco.es
Imported by :
Costco Wholesale UK Ltd /
Costco Online UK Ltd
Hartspring Lane
Watford, Herts
WD25 8JS
United Kingdom
01923 213113
www.costco.co.uk
Distributed by:
Costco Wholesale Corporation
P.O. Box 34535
Seattle, WA 98124-1535
USA
1-800-774-2678
www.costco.com
Imported by / Importé par :
Costco Wholesale Canada Ltd.*
415 W. Hunt Club Road
Ottawa, Ontario
K2E 1C5, Canada
1-800-463-3783
www.costco.ca
*faisant affaire au Québec sous
le nom les Entrepôts Costco
Importado por :
Importadora Primex S.A. de C.V.
Blvd. Magnocentro No. 4
San Fernando La Herradura
Huixquilucan, Estado de México
C.P. 52765
RFC: IPR-930907-S70
(55)-5246-5500
www.costco.com.mx
Imported by :
Costco Wholesale Australia Pty Ltd
17-21 Parramatta Road
Lidcombe NSW 2141
Australia
www.costco.com.au
Imported by :
Costco Wholesale Japan Ltd.
3-1-4 Ikegami-Shincho
Kawasaki-ku, Kawasaki-shi,
Kanagawa 210-0832 Japan
044-281-2600
www.costco.co.jp
Imported and Distributed by :
Costco Wholesale Korea, Ltd.
40, Iljik-ro
Gwangmyeong-si
Gyeonggi-do, 14347, Korea
1899-9900
www.costco.co.kr
Imported by / Manufactured for:
Costco PresidentTaiwan, Inc.
No. 656 Chung-Hwa 5th Road
Kaohsiung, Taiwan
CompanyTax ID: 96972798
449-9909 or 02-449-9909 (if cellphone)
www.costco.com.tw
Imported by and Distributed by:
Shanghai Minhang Costco Trading
Co., Ltd.
Unit 109, NO 388, Lian You Road
Minhang District, Shanghai
China 201107
[phone]

-
ATLeisure, LLC
F
3.04公尺／10呎太陽能LED
懸臂戶外遮陽傘
（附底座）
組裝、維護與使用手冊
商品編號 1900783、1237211
型號：#UMB-955258
內含重要資訊：請保留以供日後參考
請詳閱
需要有關使用、零件或客服的協助時，請聯絡：
美國免費專線：1-855-880-7205（英語服務）
加拿大免費專線：1-888-692-1033（法語服務）
來電請於東岸標準時間，週一至週五、上午8點至下午5點
www.atleisure.com．電子郵件：[email protected]
請勿將商品退回店家
僅供居家戶外使用。不得作為營業用。
美國設計
中國製造

15
C
GG
F
HH
D
N
E
A
B
L
JJ
M
G1
N1
CAN
G
E2
F
................................... 15
16
16
17-19
19-21
22
23
23
.............................. . . 23
...................................... 24
....... . .... . ...................... 24
... . . . ....................... 25
K
目錄
準備工作
組裝所需的工具（產品未附）
五金與包裝內容物
組裝說明
操作說明
燈具操作與電池更換
電池的處置
維護與保養
警告與注意事項
產品保固
保固要求
更換零件
.....................
............................
.................................
.................................
...........................
.................................
.................................
準備工作
開始組裝產品之前，應確認內容物已全數齊備。將所有零件擺放在乾淨、平坦的表
面。以包裝內容物的明細以及下方圖面進行零件比對。若有任何零件遺漏或受損，
請勿嘗試組裝產品或是將產品退回購買地點。請與我們的客服聯絡，來電請撥：1-
855-880-7205（英語服務）或 1-888-692-1033（法語服務），以尋求更換零件
或進一步的指示說明。
預計組裝時間：40分鐘
組裝所需的工具：開口扳手或可調扳手（產品未附）

16 F
A 2
B 2
C 1
CAN 1
D 1
E 1
E2 1
F 1
G 2
G1 1
K 1
L 1
M 4
N 1
N1 1
1
GG 外六角螺栓 M10-1.5x20 A2-70 4
HH
平墊圈 M10 A2-70 4
JJ 內六角螺栓 M8 A2-70 2
KK 內六角扳手 M8 1
組裝所需的工具（產品未附）
五金內容物
包裝內容物
圖示 內容說明
可調扳手
圖示 內容說明零件
數量
數量
數量內容說明零件
可調扳手
中空成型底座外側
中空成型底座內側
下方橫支架
遮篷（與陽傘架相接）
上方橫支架
360˚曲柄把手
遮篷曲柄把手
固定杆
電池
電源供應器
固定杆套管軸環
固定杆支撐保護罩
中空成型底座蓋
陽傘架（含遮篷）
太陽能板

17
F
D
C
F
HH GG
D
C
M
A
L
B
F
組裝說明
注意：在移除防護材料時，請勿使用刀子或剪刀等尖銳工具或設備，這會使產品
受損。請小心不要將小型零件，例如螺栓、墊圈等物件丟棄，這些零件會包裝在
防護材料內。
警告：開啟陽傘之前，應依手冊指示完成組裝作業。將底座各部位裝入沙袋。加
入水使沙子濕潤並持續在各部分加水至頂部。以底座蓋將孔洞蓋好。建議上、下
方橫支架應擺放至少91公斤（200磅）的重量以確保穩固性。未作到此項要求會
導致重量不平均而造成陽傘傾斜，使得產品受損以及／或造成人身傷害。
沙子（4袋）
22.75公斤
50磅
22.75公斤
50磅
22.75公斤
50磅
22.75公斤
50磅
91公斤／200磅
步驟1：下方橫支架(C)放在地面，對齊
凹槽後將上方橫支架(D)放置在下方橫支
架(C)上。
步驟2：使用螺栓(GG)及墊圈(HH)（裝
在氣泡包裝內）將固定杆(F)與底座安裝
固定。注意請勿鎖過緊。調整固定杆(F)
以確保其正確地固定在底座上。最後，
以可調扳手或開口扳手（產品未附）將
其鎖緊。
步驟3：將沙袋裝入各底座(A與B)，再蓋上中空成型底座蓋(M)。把固定杆支撐保
護罩(L)放置固定杆(F)上，再裝設在中空成型底座內側(B)的上方。

18 F
N1
G
組裝說明（接上頁）
步驟4：如上圖所示，將插頭插入太陽能板下方的插座內。
步驟5：把太陽能板安裝在陽傘頂端，並將插頭及電線藏在頂端的孔位內。
接著再以順時針方向轉動固定太陽能板。請勿鎖得過緊。
步驟6：由附加套件內取出電池(G)並放入位在移動把手支柱上的電池座。接
著，在首次使用前先將太陽能遮陽傘放置在陽光可直接照射的戶外，讓太陽
能板進行八小時的充電。
確認陽傘的LED燈為關閉的狀態，以便太陽能板能夠充飽電量。

19 F
Crank
Glide Handle Grip
F
N
N
FJJ E2
E
E2
E
組裝說明（接上頁）
注意：建議由另一名人員協助將陽傘安裝在固定杆。
步驟7：將包含遮篷的陽傘架(N)與固定杆(F)安裝固定。同時，將固定杆軸環安裝在
固定杆。以六角扳手將鎖入固定杆的兩顆六角螺栓(JJ)鎖緊固定。將遮篷曲柄把手
(E2)裝在移動把手上，而360˚曲柄把手(E)則安裝於固定杆。
操作說明
步驟1：鬆開遮篷及杆子周圍的收納束帶。
步驟2：張開陽傘時，同時緊握移動把手以及握把，由杆子向上或向下移動，以調整至
想要的傾斜角度。放開握把即可固定就位。張開遮篷時，順時針轉動曲柄把手直到遮
篷完全張開至圖面所示的狀態。
張開遮篷
開啟
關閉
曲柄
握把
移動把手

20
E
F
PSMϢ
F
操作說明（接上頁）
遮篷以360˚旋轉移
動之範例
步驟3：可360˚轉動遮篷。轉動遮篷時，將曲柄把手(E)插入固定杆(F)並轉動曲
柄把手直到移至所需的位置。
步驟4：關閉陽傘時，逆時針轉動曲柄把手直到遮篷完全閉合。同時緊握移動把
手及握把，接著由杆子向下滑動，鬆開握把即可固定就位。以收納束帶固定好遮
篷以及桿子。
關閉遮篷
曲柄
關閉
張開
移動把手
握把