Atleisure UMB-M70629 Installation guide

8.5 ft Square Offset Umbrella
Assembly & Care Instructions
IMPORTANT: RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
Item Number: M70629
Model: UMB-M70629
Toll Free: 1-855-880-7205
8am - 5pm, Monday through Friday, Eastern Standard Time
DO NOT RETURN TO STORE
For outdoor domestic use only. Not for commercial use.
Designed in USA
Made in China
For assistance with assembly, parts, or customer service, please contact:

2
Contents
Package Contents
Assembly and Use
Replacement Parts
Care and Maintenance
Warning and Cautions
Warranty
2
3 - 6
8
7
7
7
Package Contents
Compare carton contents with package contents list. If any part is missing or
damaged, call customer service TOLL FREE at 1-855-880-7205 for replacement parts
or further assistance.
tance.
Part Description Quantity
A Outer Base Components 2
B Inner Base Components 2
C Lower Cross Leg 1
D Upper Cross Leg 1
F Holder Pole w/ Control Knobs 1
N Umbrella Frame with Canopy 1
L Pole Support Cup 1
M Base Cap 4
M1 Base Cap Inner Seal (pre-assembled) 4
GG Hex Bolt 4
HH Flat Washer 4
1x
D
1x
C
1x
F
1x
N
4x
GG
1x
L
4x
HH
2x
2x
4x
1
CAUTION:Do not use sharp objects to remove the protective material, as it
may damage the product.

3
Assembly and Use
Step 1: Place Upper Cross Leg (D) over Lower Cross Leg (C) to form “X” shape.
Tools Required for Assembly: Open end wrench or adjustable wrench (not
included).
Step 3: Attach Pole Holder (F) to cross legs (C&D) using screws (GG) and washers
(HH) found in blister pack. Hand tighten only. Adjust Pole Holder (F) until positioned
correctly on base. Tighten all bolts being careful not to over-tighten.
F

4
Assembly and Use (cont
A
B
M
F
’d)
Step 3: Lay base components (A&B) on top of cross legs to form rectangular base.
Step 4: Unscrew caps from each section of umbrella base and fill with sand no less
than 33 lbs. Reposition caps and tighten into place.

L
5
Assembly and Use (cont’d)
Step 5: Pull holder pole ring from top of Holder Pole (F) and unscrew both control
knobs. Slide Pole Support Cup (L) onto Holder Pole (F). Replace control knobs and
holder pole ring.
Step 6: Insert Umbrella Frame (N) into Holder Pole (F) and tighten control knobs to
secure the umbrella in place. Fixed stop pin on frame will rest on holder pole ring.
Unfasten storage staps before use.
WARNING: Fully assemble umbrella base prior to inserting frame to avoid
umbrella tipping. Failure to assemble and install as instructed could result in
the umbrella tipping over, causing personal injury and/or property damage.
Storage Straps
Holder Pole Ring
Control Knobs
N
Storage Straps

6
Assembly and Use (cont’d)
Step 7: To open umbrella, pull out Lever Clamp to release Glide Handle. Grasp and
slide Glide Handle up along Umbrella Pole. Turn Crank Handle to right until Lower
Center Hub reaches end of Support Pole (shown above) and canopy has proper
tension. Push Lever Clamp down to lock Glide Handle in place at desired angle.
Step 8: To close umbrella, pull out Lever Clamp and slide Glide Handle down
Umbrella Pole. Turn Crank Handle to left until the canopy is fully closed. Secure with
straps.
Step 9: To rotate canopy 360 degrees, loosen control knobs on Holder Pole and turn
umbrella to desired postion. Re-tighten control knobs to secure.
Control
kno
b
Rotate
Lever clamp
Glide handle
Crank handle

7
Warning and Cautions
Care and Maintenance
• Use mild soap and warm water to clean canopy. Rinse with clean water and dry
thoroughly. Do not machine wash. Do not iron. Air dry the canopy thoroughly before storing for
extended periods of time. Make sure the canopy is completely open during drying process to
prevent shrinkage.
• If crank becomes too hard to turn, check to see if rope has slipped off pulley. If you continue
to crank, the rope or crank handle may break. If parts have broken, call customer service, toll
free: 1-855-880-7205 8am-5pm, Monday - Friday, Eastern Time.
• Placement of umbrella over or near a swimming pool will cause premature fading not covered
under our warranty.
Warranty
90 DAY WARRANTY
This product is covered under a manufacturer’s 90 day warranty from date of
purchase against defects in materials and workmanship. This warranty does not
cover damage due to neglect, abuse or weather related damage. For full warranty
disclosure, email us at customerser[email protected], call toll free at 1-855-880-
7205 or send mail to: 1040 Boulevard SE Ste. B, Atlanta GA 30312
HOW TO FILE A CLAIM
If you are within your warranty you must have your receipt and pictures of your
information to send to ATLeisure at [email protected], or send by mail
to 1040 Boulevard SE Ste. B, Atlanta GA 30312. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.

8
Replacement Parts
For replacement parts, call our customer service department at:
1-855-880-7205, 8am - 5pm EST, Monday - Friday.
Part Description Re-order Number
ABASE (OUTSIDE) UMB-M70629-BSE-OUT
BBASE (INSIDE) UMB-M70629-BSE-IN
CLOWER CROSS LEG UMB-M70629-LCL
CAN CANOPY (TAN)
CANOPY (RED)
CANOPY (BLUE)
UMB-M70629-CAN-TAN
UMB-M70629-CAN-RED
UMB-M70629-CAN-BL
D UPPER CROSS LEG UMB-M70629-UCL
F HOLDER POLE UMB-M70629-HDP
LPOLE SUPPORT CUP UMB-M70629-PSC
M
M1
BASE CAP
BASE CAP INNER SEAL
UMB-M70629-BSE-CAP
UMB-M70629-BSE-SEAL
OHOLDER POLE RING UMB-M70629-HDP-RING
PCONTROL KNOBS UMB-M70629-CTRL-KNOB
KIT HARDWARE KIT FOR M70629 UMB-M70629-HDW-KIT
ATLeisure, LLC
1040 Boulevard SE, Suite B
Atlanta, Georgia 30312, USA
Customer Service Toll Free 1-855-880-7205
8am - 5pm Eastern Time, Monday through Friday
www.atleisure.com
This Atleisure product is covered by U.S. Patent No. 8,104,492