REX A-1-9 and REX A-3-9 –Standalone or access controller
Installation of Rex A
A special holder, provided with the controller, is needed for
attachment to the wall. Two screws are enclosed in the box. After
the holder has been affixed, put the controller onto the holder and
press –after you hear the click, it is fixed. If you want to remove
the controller from the wall, put the screwdriver under the
controller’s casing (as close as possible to the holder’s attachment
points) and turn it gently.
Installation holder for A box.
AS A STANDALONE CONTROLLER
The entire set-up procedure is carried out with the master card.
You can register two master cards.
The master cards cannot be replaced or duplicated. After
registration the master cards should always be kept in a
secure place. You cannot change any setting without them
and neither can we. Keep that in mind when storing the
master cards.
Programming with the master card
First connection to the power supply and registration of the
master cards:
Turn the power supply on (2 beeps indicate power on). One by one
approach two cards you will use as a master cards (3 beeps
indicate a successful registration). The first two cards registered
become master cards. All the other cards will be registered as
users (user cards). You can register only one master card if you
approach the same card twice.
Usage of master card:
If you hold the master card in front of the controller, every 2
seconds a double beep is heard. The number of double beeps
indicates the programming function.
PROGRAMMING FUNCTIONS WITH MASTER CARD
Register or delete user cards
Pulse time/ Duration of active output or toggle mode
Door status switch input/ Time till pre-alarm
Negate / Switch output state
Switch to Wiegand 26-bit, table reader or access
controller
Sound (off/on), alarm output (off/on), door status
switch input NC or NO, set time in minutes or
seconds
Description of programming functions
Function 1) User cards
Register or delete user cards. With a registered card, output (O0,
wire 3) for an el. strike is triggered for the time set in the function
2. In the controller, registered cards are arranged in order of their
registration. Every registered card is saved to its own position.
Register user card with master card:
Approach the master card and remove it after 1 double beep.
Within a period of three seconds approach a user card. You can
register more cards at once, if you approach them one by one. The
user card is now registered and with it, you can open output on the
controller. If the card has already been registered, it is now deleted
and its position is now empty. Next registered card will take the
first available position on the list or position of the deleted card.
When you have register/deleted all of the cards, wait until the
controller confirms it with double beep. To delete a lost user card,
you must maintain a list of registered cards, arranged in order of
registrations (positions).
Function 2) Pulse time/ Duration of active output or toggle
mode
Set the duration of active output/ the time in which you can open
the door or set output to toggle mode. Toggle mode means, if a
user card is registered, output will remain opened (if it was closed)
or closed (if it was open) till next registration. The time can be set
in seconds or minutes. Switching time from seconds to minutes and
back, can be adjusted by using the function 15.
Set the duration of active output with master card:
Approach the master card and remove it after 2 double beeps. The
controller will start to beep every second. Each beep indicates 1
second or 1 minute of active output. Duration of active output can
be max. 120 seconds or 60 minutes. When you hear the required
number of beeps, approach a user card for confirmation.
Set toggle mode with master card:
Approach the master card and remove it after 2 double beeps.
Approach a user card before the first beep. Toggle mode is
selected.
Function 3) Door status switch input
Set the time till pre-alarm / time in which the door can stay open,
without triggering the pre-alarm and consequently the alarm. This
function is used when the door status switch on el. strike is
connected to Input0/I0/wire 5 on the controller. The input is
normally opened (NO) by default. It can be changed to normally
closed (NC) by using the function 15. The time can be set in
seconds or minutes. Switching time from seconds to minutes and
back, can be adjusted by using the function 15.
Set the time till pre-alarm with master card:
Approach the master card and remove it after 3 double beeps. The
controller will start to beep every second. Each beep indicates 1
second or 1 minute till pre-alarm. Duration of the time till pre-
alarm can be max. 120 seconds or 60 minutes. When you hear the
required number of beeps, approach a user card for confirmation.
Function 4) Pre-alarm and alarm
Set the pre-alarm time. This is the time in which the controller,
with short beeps, alerts you that the door was left open. If you
don’t close the door in the pre-alarm time, the alarm will be
triggered and signaled with long beeps by the controller. The time
can be set in seconds or minutes. Switching time from seconds to
minutes and back, can be adjusted by using the function 15.
Set the pre-alarm time with master card:
Approach the master card and remove it after 4 double beeps. The
controller will start to beep every second. Each beep indicates 1
second or 1 minute of the pre-alarm time. Duration of the pre-
alarm time can be max. 120 seconds or 60 minutes. When you
hear the required number of beeps, approach a user card for
confirmation.
Function 5) Negate / Switch output state
This function is used, when you connect an electric strike or electric
magnet which needs power supply to remain in locked state.
Switch output state with master card:
Approach the master card and remove it after 5 double beeps.
Within a period of three seconds approach a user card. The output
state will be switched from the current one.
