Atlona AT-HDR-H2H-88MA User manual

Installation Guide
1
AT-HDR-H2H-88MA
4K HDR 8×8 HDMI to HDMI Matrix Switcher
AT-HDR-H2H-88MA
1 x AT-HDR-H2H-88MA
1 x Captive screw connector, 5-pin
8 x Captive screw connector, 4-pin
1 x 24V DC power supply
1 x Pair mounting ears w/screws
4 x Feet w/screws
1 x IR remote control
1 x Installation Guide
Package Contents
The Atlona AT-HDR-H2H-88MA is an 8×8 HDMI matrix switcher for high dynamic range (HDR)
formats. It is HDCP 2.2 compliant and supports 4K/UHD video @ 60 Hz with 4:4:4 chroma
sampling, as well as HDMI data rates up to 18 Gbps. The AT-HDR-H2H-88MA is ideal for
professional HDMI signal routing in residential and commercial applications were a number of AV
sources must be shared throughout eight zones to reduce the installed equipment footprint and
to reduce the costs associated with multiple, redundant devices. It is compatible with all video
resolutions, audio formats, and color space formats supported in the HDMI 2.0b specication,
plus the ability to pass metadata for HDR content. The HDR-H2H-88MA includes EDID and
HDCP management features, and can send CEC display control independently to each output.
An unbalanced analog audio output is paired with each HDMI input for sending de-embedded
HDMI audio to a whole-house audio system. The HDR-H2H-88MA can be controlled via Ethernet,
RS-232, and IR. A handheld IR remote control is included.
IMPORTANT: Visit http://www.atlona.com/product/AT-HDR-H2H-88MA for the latest
rmware updates and User Manual.

Installation Guide
2
AT-HDR-H2H-88MA
AT-HDR-H2H-88MA
23
67 POWER
FNC INFO
ENTER
CANCEL
1
5
EDID
4
8
FW
DC 24V
876543
218
7
65
4
3
21
RS-232 IR IN
SRX TX
HDMI IN
AUDIO OUT
4321 8765
RLRLRLRL RLRLRLRL
HDMI OUT
LAN
1 Function Buttons
Power - Sets the unit in and out of
standby.
Enter - Used for making selection within
the front panel OSD.
FNC - Use to switch number buttons to
their secondary function.
CANCEL - Navigates back one step in the
front panel OSD.
2 Number Buttons
Use for selection of inputs and outputs.
1- Press FNC + 1 to route selected input
to all outputs.
2- Press FNC + 2 to turn the IR receiver
window on and o.
3- Press FNC + 5 to open the EDID menu.
4- Press FNC + 6 to display the device
rmware. Press 6 again to view IP, IP port,
and MAC.
3 HDMI IN
Connect HDMI cables to these ports from
HDMI sources.
4 AUDIO OUT
This port provides source audio 2CH de-
embedding. The audio of the HDMI inputs
will be directly de-embedded to an audio
DSP, amplier, or player device.
5 HDMI OUT
Connect an HDMI cable from this port to
an HDMI display, extender, or switcher.
6 LAN
Connect an Ethernet cable from this port
to a Local Area Network (LAN). This port
provides access to the webGUI or TCP/
IP control.
7 FW
Connect a mini USB cable to this port to
update the rmware.
8 Control Port
Connect a third party controller or PC
to control the matrix through either IR or
RS-232
9 DC 24V
Connect the included 24V DC power
supply to this power receptacle.
Panel Descriptions
35
467 8
9
12
Pin out will be determined by the
RS-232 cable and connect as
RX (receive), TX (transmit) and
(Ground).
A 5-pin captive screw connector for control has been included. The rst three terminals are RS-
232 control, the last two terminals are for IR.
IR IN is connected by a ground and
signal wire. Use with 3rd party control
systems. For easy termination, Atlona
recommends using the 2 meter IR
cable AT-LC-CS-IR-2M.
Control
RS-232 IR
GND S
GND RX TX
GNDRX TX

Installation Guide
3
AT-HDR-H2H-88MA
AT-HDR-H2H-44M
1 2 3 4
RS-232 IR IN
HDMI IN LAN FW DC 24V
SRX TX
OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4
AT-HDR-H2H-88MA
23
67
POWER
FNC INFO
ENTER
CANCEL
1
5
EDID
4
8
Mounting Instructions
The AT-HDR-H2H-88MA can be mounted in a standard 19-inch rack or placed freestanding on
top of a desk or table.
Rack installation
1. Remove the front two case screws from the sides of the case.
2. Attach the included rack ears to each side of the AT-HDR-H2H-88MA using the case
screws.
AT-HDR
Audio
LR
Connect to an audio DSP, amplier, or other
audio distribution or player devices. Only
unbalanced connections may be used.
Ground
L - Signal
Ground
R - Signal
Unbalanced
NOTE: Audio is directly de-embedded
from the HDMI IN ports and are not zone
output audio ports.

Installation Guide
4
AT-HDR-H2H-88MA
Surface mounting
The AT-HDR-H2H-88MA can be placed freestanding on top of a desk, a table, or in a cabinet.
To prevent damage to the surfaces or unnecessary movement of the matrix, four feet have been
included.
1. Turn the unit upside down.
2. Install each foot using the included feet screws, the rubber grips of the feet should be facing
up during installation.
3. Turn the unit right-side up and place it in the desired location.
AT-HDR-H2H-44M
12
34
POWER
FNC EDID INFO
ENTER
CANCEL
AT-HDR-H2H-88MA
23
67
POWER
FNC INFO
ENTER
CANCEL
1
5
EDID
4
8
AT-HDR-H2H-44M
12 3 4
RS-232IR IN
HDMIIN LAN FW DC24V
S
RXTX
OUTPUT1 OUTPUT2 OUTPUT3 OUTPUT4
AT-HDR-H2H-88MA
23
6 7POWER
FNC INFO
ENTER
CANCEL
1
5
EDID
4
8
NOTE: Increase the air ow as needed to
maintain the recommended temperature inside
the rack.
NOTE: Do not exceed the maximum weight
loads for the rack. Install heaver equipment in
the lower part of the rack for stability.
3. Install the HDR-H2H into a rack, using four rack screws.

Installation Guide
5
AT-HDR-H2H-88MA
1. Connect up to 8 HDMI sources to the HDMI IN ports.
2. Connect up to 8 HDMI displays to the HDMI OUT ports.
3. For control, connect to the captive screw port for IR and RS-232, or the LAN port for TCP/
IP and webGUI.
4. Connect the included 24V power supply to the DC 24V port.
5. Connect the power supply to an AC outlet.
Installation
WebGUI
The AT-HDR-H2H-88MA includes a built-in webGUI, which allows easy management and control
of all features. Follow the instructions below to access the webGUI.
1. View the IP address of the unit using the front panel OSD.
• Press the FNC button.
• Press button 6 (INFO). The rmware version will display on the front panel screen.
• Press button 6 again to bring up the IP address.
2. Launch a web browser and enter the IP address of the unit.
3. The AT-HDR-H2H-88MA Login page will be displayed.
4. Enter the following information on the Login page.
Login: root
Password: Atlona
5. Click the Login button.
NOTE: If there is no IP address or the unit is not connected to a DHCP network, press
and hold buttons 1 + 2 for 5 seconds to switch the unit to a static IP address. The default
static IP address and netmask is 192.168.1.254 255.255.0.0.
AMS 2.0
For full conguration of the HDR-H2H-88MA, AMS 2.0 is available from https://atlona.com/AMS
for free. Two options can be used for installation: The free Linux based software download or the
easy to install server hardware (AT-AMS-HW).
Once AMS has been set up:
1. Open a browser on the same network as AMS 2.0 and go to the IP of AMS 2.0.
a. View the AMS 2.0 installation instructions on how to nd the IP of the software.
2. Enter the login information on the AMS 2.0 web page, then click the Login button.
3. View the AT-HDR-H2H-88MA manual for routing and conguration.

Installation Guide
6
AT-HDR-H2H-88MA
Connection Diagram
DC5V HDBaseTIN HDMIOUT
DC5V HDBaseT OUT HDMIIN
Video
AT-HDR-EX-70-2PS-TX AT-HDR-EX-70-2PS-RX
AT-HDR-H2H-88MA
Display
Display
Video
Audio
Control
Video
Video
Video
Audio
Audio
Audio
Video
Video
HDBaseT
Set-Top Box
Automation
Control System
Media Player
Projector
Blu-ray Player
SET-TOPBOX
OK
224
2
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
+12V
SIG
GND
+12V
SIG
GND
+12V
SIG
GND
+12V
SIG
GND
1
COMPONENT
HDMI
1
2
3
4
5
6
SERIAL1
IROUT SERIAL 2
L
R
DIGITAL
COAXOUT
AUDIOOUT AUDIOIN ETHERNET
2 3 4
VIDEOOUT
48VDC
FACTORY
RESET
4
media4
AT-HDR-H2H-44M
1 2 3 4
RS-232 IR IN
HDMIIN LAN FW DC24V
SRXTX
OUTPUT1 OUTPUT2 OUTPUT3 OUTPUT4
AT-HDR-H2H-88MA
23
67
POWER
FNC INFO
ENTER
CANCEL
1
5
EDID
4
8
Matrix Mutli-zone Amplifier
CH1POWER CH2 CH3 CH4
CH5 CH6 CH7 CH8
I
0

Installation Guide
7
AT-HDR-H2H-88MA
Troubleshooting
Problem Solution
I am not receiving
multichannel audio or 3D
video.
• By default, multichannel audio and 3D will not pass
unless all devices support those features. Set each port’s
EDID through the front panel, webGUI, or RS-232.
What rmware am I on? • To view the device rmware version, press the FNC
button, followed by button 4 (INFO). The rmware will
appear on the front panel OSD.
What’s my baud rate? • To view the baud rate of the RS-232 port, press the FNC
button, followed by button 4, then press button 2. The
baud rate will appear on the front panel OSD.
What’s my IP? • To view the IP address of the unit, press the FNC button,
followed by the 6 button twice.
• If the unit is connected to a non-DHCP network, press
and hold the 1 + 2 button for 5 seconds to switch to
a static IP address. The default static IP address is
192.168.1.254.

Installation Guide
8
AT-HDR-H2H-88MA
© 2017 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered
trademarks are the property of their respective owners. Pricing, specications and availability subject to change without notice. Actual products, product images, and
online product images may vary from images shown here.
Version 1
atlona.com •408.962.0515 •877.536.3976