Atlona AT-PRO130HD User manual

AT-PRO130HD
MANUAL
www.atlona.com

This manual is only for operational instruction, not for any maintenance service.
The manufacturer will make a supplement for any function or parameter revision.
The copyright of AT-PRO130HD USER MANUAL belongs to the manufacturer,
any company or individual uses part of, or all content of the manual for any
commercial purpose without the consent of manufacturer is prohibited.
Please check Atlona website or contact local Atlona Distributor for updates.
www.atlona.com
Attention:
In order to ensure the credibility use of the product and the user’s safety, please
comply with the following items during installation and maintenance:
The system must be earthed properly. Please do not use two blades plugs and
ensure the alternating power supply ranged from 100v to 240v and from 50Hz to
60Hz.
To avoid any damage by over heat, please keep the working environment good in
ventilation to radiate the heat when running the machine.
The machine should be turned off when in rainy and humid days or nonuse for a
long time.
The AC power supply line should be disconnected with the power socket during
the following operation.
A. Take out or reinstall any component of the machine.
B. Disconnect or re-connect any connector of the machine.
Please do not attempt to maintain and uncover the machine for there is a high-
voltage component inside and the risk of the electric shock.
Do not splash any chemical product or liquid on or near the equipment.
Operation Notice:
www.atlona.com 1

Dimensions:
Features:
The AT-PRO130HD is a Seamless scaler/switcher designed for multi-signal processing, Composite
VIDEO, S-VIDEO, VGA and HDMI can be scaled to high-resolution VGA or HDMI formats.
* Composite video, S-Video, VGA and HDMI can be switched to VGA or HDMI outputs with the following
Resolutions:
SVGA 800X600 @60Hz
XGA 1024X768@60Hz
SXGA 1280X1024@60Hz
* Pal/NTSC AutoDetect and Conversion
* 2MIC inputs, separated volume circuit enable the connection with the master audio signal
* 3 wide-band VGA input signals switching
* Adjustable Brightness, contrast, saturation of VIDEO and S-Video
* IR remote control and serial control
* Built-in memory card with the power-fail protection Specially dedicated to the high-resolution
A/V presentation display, multimedia classrooms, command centers, conference rooms, etc.
www.atlona.com 2

Function:
Front Panel
• 1. LCD display
• 2. Signal Source selection, To select input Signal Source (HDMI, VGA,
Composite Video, S-Video , etc.)
HDMI Signal: Mainly for Cable Box or BluRay Player
VGA Signal: Mainly for PC or NOTEBOOK
Composite Video: CVBS, such as DVD,VCD,VCR ,etc.
S-Video: super DVD, VCD or video card, etc.
• 3. Signal Indication light
• 4. Source Switching: Selecting the corresponding input channel (1,2,3,4) of current
signal source. Please select before switching.
• 5. Resolution Display: Press it to enter the setting mode, press again to change the
resolution, with LCD status displaying.
• 6. MIC volume adjustment, with LCD and bar indicator.
• 7. Mute/Backlight setting: 1. Mute is available for both MIC and master volume; 2.
Under power-off status, pressing MUTING continuously while resuming
power supply to enter back light setting mode, setting range is 0-99 minutes.
• 8. Master vol adjustment. with LCD and bar indicator.
• 9. Power status indication
• 10. IR Sensor
• 10. MIC
Rear Panel
www.atlona.com 3

Remote control:
VIDEO Audio input ports
4-channel audio signal inputs
S-VIDEO Audio input ports
4-channel S-VIDEO audio signal inputs
VGA Audio input ports
3-channel VGA audio signal inputs
HDMI input ports
1-channel HDMI video/audio signal input
MIC inputs
2 MIC ports
Outputs:
VGA/HDMI signal outputs
1x VGA and 1 x HDMI signal output ports, one for monitor, the other for main outputs.
RS232 control ports
Connecting to computer or 3rd party control system with RS232
Power (AC100V~240V)
System power supply. Adapting to AC100V~240V 50Hz/60Hz automatically
Functions are the same as of the front panel.
1 Model and Channel choosing
Using remote to choose channels
2 Resolution choosing
SVGA,XGA,SXGA --3 types of resolution:
SVGA 800×600 @75Hz
XGA 1024×768@60Hz
SXGA 1280×1024@60Hz
3 MIC volume adjust
www.atlona.com 4

RS-232 COMMANDS:
Code Function
01*01! VGA1 with audio switch out
02*01!
HDMI2 with audio switch out
03*01! VGA3 with audio switch out
04*01! VGA4 with audio switch out
05*01! S-VIDEO1 with audio switch out
06*01! S-VIDEO2 with audio switch out
07*01! S-VIDEO3 with audio switch out
08*01! S-VIDEO4 with audio switch out
09*01! COMPOSITE1 VIDEO1 with audio
switch out
10*01! COMPOSITE2 VIDEO1 with audio
switch out
11*01! COMPOSITE3 VIDEO1 with audio
switch out
12*01! COMPOSITE4 VIDEO1 with audio
switch out
01$01! SVGA 800*600
02$01! XGA 1024*768 (default)
03$01! SXGA 1280*1024
04$01! MIC volume level up
05$01! MIC volume level down
06$01! Master volume level up
07$01! Master volume level down
08$01! Mute on
09$01! Mute off
11$01! restore the Video(CVBS) Brightness…
to the default value
12$01! restore the S-Video( YC ) Brightness…
to the default value
xx$02! select the Video brightness 00--99% (0<
xx <100)
xx$03! select the Video Contrast 00--99% (0<
xx <100)
xx$04! select the Video Saturation 00--99% (0<
xx <100)
xx$05! select the S-Video brightness 00--99%
(0< xx <100)
xx$06! select the S-Video Contrast 00--99%
(0< xx <100)
www.atlona.com 5

Code Function
xx$07! select the S-Video Saturation, 00--99%
(0< xx <100)
01#08! read present state
02#08! read present Firmware Ver.
03#08! read system information
Description for Compsite Video:
Press Video for 3 seconds under Video mode to enter the setting mode.
function_1: 1 CV brightness, brightness adjustment, works with
Parameter +, parameter -.
function_2: 2 CV Contrast, Contrast adjustment, works with parameter+,
parameter -.
function_3: 3 CV Saturation, Saturation adjustment, works with
Parameter +, parameter -.
function_4: 4 RESTORE CVBS DEFAULT VALUE?, works with ENTER.
Resets back to default.
Description for S - Video:
Press S-Video for 3 seconds under S-Video mode to enter the setting mode.
function_1: 1 SV brightness, brightness adjustment, works with
parameter +, parameter -.
function_2: 2 SV Contrast, Contrast adjustment, works with parameter +,
parameter -.
function_3: 3 SV Saturation, Saturation adjustment, works with
parameter +, parameter -.
function_4: 4 RESTORE SV DEFAULT VALUE?, works with ENTER. Resets back to default.
www.atlona.com 6

model
specication
AT-PRO130HD
Video
Gain 0 dB
Bandwidth AV video:150MHz, S-video video:150MHz,VGA video:375 MHz.
Multi-channel
input :one-channel
-50dB @50 MHz, -45dB @10 MHz
DC phase/OS <1.28 Degree,3.58 MHz
DC phase deviation 0.1%,3.58-4.43 MHz
DC gain deviation 0.1 Degree, 3.58-4.43 MHz
Switch speed 100 ns(Max)
Signal type
HDMI, VGA, S-video, Composite video
Video input AV S-Video
HDMI/VGA
Connector RCA
female connector
S-Video
Connector(Y-C)
female connector
Signal intensity
1V p-p : Y component video S-video,composite video 0.7V p-p:
VGA(Computer signal) 0.3V p-p:
Min/Max EL Analog signal: -3V/+3V
Impedance 75 Ω
Echo lost <-30dB@5MHz
Level frequency
response
60-200KHZ
Vertical frequency
response
100Hz-200Hz
VGA Video output
Connector
15-pin HD15 female connector and HDMI
Min/Max EL -2.0V / +2.0V
Impedance 75 Ω
Echo lost <-40dB@5MHz
Direct current
compensation
Max±5mV
VGA sync signal
Signal type
HDMI, RGBHV, RGBS, RGsB, RsGsBs,Composite,component,S-video
Video type
NTSC 3.58, NTSC 4.43, PAL, SECAM
Input EL 0.5V- 5.0V p-p,: 4.0V p-p normal
Output EL AGC-TTL: 5Vp-p, not terminated
Input impedance 510 Ω
Output impedance 75 Ω
Max transmitting
delay
level:90ns vertical:160ns
Max up/down time 4ns
Plus or minus
www.atlona.com 7

model
specication
AT-PRO130HD
Audio signal
Input/output
connector
8-channel RCA imbalance input,4-channel 3.5mm imbalance output
Gain 0 dB
Frequency
response
20 Hz ~ 20 kHz,
Total harmonic
component lost and
noise
0.05% @ 1 kHz (rating voltage)
(S/N ) >8dB
Stereo separation >80dB @ 1 kHz
(CMRR) >75dB @: 20 Hz ~ 20 kHz
Signal type Stereo (imbalance)
Impedance input:>10 kΩ(balance/imbalance)
output:50 Ω (imbalance), 100 Ω(balance)
Max input EL +19.5dBu, (balance/imbalance)
Gain deviation ±0.1dB @20 Hz ~ 20 kHz
Max output EL +19.5dBu, (balance/imbalance)
MIC
MIC type Moving-coil type
Input sensitivity 25mV
FR response 50Hz-16K Hz-
Connector type Single input
Control type
Serial control RS-232, 9-pin female D type
Baud rate and
protocol
Baud rate:9600, data bit:8, stop bit:1, non parity0
Serial control
structure
2 = TX, 3 = RX, 5 = GND
Specication
Power 100VAC ~ 240VAC, 50/60 Hz, international auto adapting power
Temperature Deposit using temperature: -20° ~ +70°C
Humidity Deposit using temperature:10% ~ 90%
Cover dimension 483(L)X230(W)X44mm(H)
Product weight 1.9kg
MTBF 30,000 hours
Quality warranty Guarantee to keep it in good repair for 1 year,
www.atlona.com 8

Troubleshooting:
1) If images output with ghost, such as the projector, please check the projector’s setting and or try another
high quality cable.
2) If there is color loss and no video signal on the output, please check the input and output connections and
the VGA cable.
3) The remote control doesn’t works:
A. Check batteries replace if needed.
B. The remote is broken please contact manufacture for repair.
4) Unable to control the scaler by computer through its COM port, please check
the COM port number and the software and make sure the COM port is in good condition.
5) If the output image is interfered, please make sure the system is grounded well.
6) If the static becomes stronger when connecting the BNC connectors, it maybe due to the
incorrect grounding, please correct it otherwise it would damage the scaler.
10) If the scaler cannot be controlled by the buttons on the front panel, RS232 port or
remote control, the scaler may have broken. Please contact the manufacture for repair/ replacement.
www.atlona.com 9