Atomic AMZ SERIES User manual

Instruction and Assembly Manual
Version 1.5 (October 2016)

Tools Needed (Not Included) :
Equipment required :
Tools Included :
Thank you for purchasing this Atomic product. BZ is a high
performance competition machine for 1:28 scale. Please read this
manual in detail in order to have proper assembly of this product
and wish you have fun with it.
Car Body Radio System Ball Diff Oil Grease
Rim Tire Battey
Small Screw Driver 1.5mm Allen wrench
1.3mm Allen wrench Diff tool
Hex Nut Driver
4.5mm
Hobby Knife
1.5mm Drill Bit 2.0mm Drill Bit #1500 Sandpaper

1.9x4KB(Silver)
2x4KM
x8
x3
Bulkhead B (+0)
Bulkhead A (+0)
11
2Apply Thrust
Bearing Grease
oil
Polish the diff plate and thrust
bearing plate with #1500 sand
paper
2.38mm
Thrust Ball
Diff Housing (Short)
Diff Housing (Long)
27T Pulley
Diff rubber
Diff Scwer
Pulley Collar
Diff Nut
Build 2 sets
2
Loosen
Tighten
After assembly
Diff tool
Ball differential
Attaching bulkheads
P.1
Apply Grease
Apply Ball Diff
Grease
M1.9x4KB (silver color)
M1.9x4KB (silver color)
2x4KM
2x4KM
Bulkhead B (+0)
Bulkhead A (+0)
Bulkhead B (+0)
Bulkhead A (+0)
Motor Mount
Spur gear shaft
Lower deck

M1.9x4PB
Bearing hub
Bearing hub
6x10x2.5
Bearing
6x10x2.5
Bearing
2x6PM
2x4x0.2
shims
2x5x2.5
Bearing
3x6x2.5
Bearing
Upper Bulkhead
B (+0)
Upper Bulkhead
A (+0)
16T Cnter Pulley
Drive belt (Short)
6x8 shims
About 0.2 mm
M1.9x4PB
6x10x2.5
Bearing
Bearing hub
Bearing hub
Upper Bulkhead
B (+2.5)
Upper Bulkhead
A (+2.5)
Drive belt (Long)
33Attaching Rear Ball differential
& Center Pully
1.9x4PB (silver)
2x6PM
x4
x1
44Attaching Front Ball differential
1.9x4PB (Silver)
x4
Upper Bulkhead
B (+0)
Upper Bulkhead
A (+0)
Upper Bulkhead
B (+2.5)
Upper Bulkhead
A (+2.5)
6x10x2.5
Bearing
P.2
6x8 shims
About 0.2mm
!
!
Attention:
!
Attention:
!
Add 0.2 mm
shims at this side
of outdrive cup.
Add 0.2 mm
shims at this side
of outdrive cup.
!

5
2x4PM
1.2x4KM
x4
x4
5
Attaching Upper deck
2x4PM
2x4PM
Upper deck
1.2x4KM
1.2x4KM
For Adjusting Bearing Hub
For Adjusting Bearing Hub
Loosen
Tighten
Loosen Tighten
Front
Rear
66Attaching Steering System
2x10PM x2
2x5x2.5
Bearing
Bell Crank
2x4x1
washer
Makeing 2
Linkage Ball A
Linkage Ball B
2x4x0.2
shims
2x10PM
Steering System
Mount
Crank Link
Attention:
Installation direction
!
!
P.3
Adjust the bearing hub
position to adjust belt
tension. Middle is the
recommended.
Make sure the carbon top deck can be
easily put on the bulk head. otherwise, use
sand paper to trim the end of top deck.

Attention:
!
Motor
77Attaching Servo Mount
2x4PM
2x4KM
x5
x2
1.5x6PB x1
8
8Attaching Spur gear & Motor gear
2x4PM
2x4KM
2x4KM
2x4KM
2x4PM
1.5x6PB
Servo
(AMZ-OP024)
Servo Mount A
Servo Mount B
Steering System
Linkage assembly
1.5x11 set screw
2.5mm Ball end
Linkage Ball A
Servo horn
1.5x11
Set screw
x1
Quick
Smooth
Steering Respond
!
Attention:
Installation direction
chamfer
Planar
chamfer
Planar
!
Motor
Motor pinion
Spur gear
5x7x1mm
O-ring
2x4KM x4
5x7x1mm
O-ring
x1
Servo assembly
P.4
!
 14 15 16 17 18
54 5.70 5.36 5.06
56 6.75 6.30 5.91 5.56 5.25
58 7.53 6.99 6.53 6.12 5.76 5.44
Motor Pinion
Spur Gear
(5.91 is recommended for 5000KV motor)
( )
Spur gear x 1.69
Motor gear = Gear ratio
Carefully adjust
the position of
pinion, make sure
it does not touch
the front belt.

99Axles assembly
3x5 shims
About 0.2~0.3mm
3x6x2
Bearing 3x6x2
Bearing
Steering block
Linkage Ball 4mm
(AMZ011)
10 Attaching Front arms
Wheel axle
Swing shaft
Cross joint
Lock collar
oil
CVD assembly
1x5.5mm
After assembly
Make sure the wheel
rotate freely.
Insert shims to
adjust the play
of CVD
10
LR
0.7mm
11 Attaching Tie Rod
11
1.2x3PB x2
1.2x3PB 2x12mm
Linkage Ball C
Camber arm
1.5X11mm
Turnbuckles
2.5mm Ball end
6.5mm
Build 2 Sets
!
Attention:
Installation direction
chamfer
Planar
chamfer
Planar
!
!
Not included
Build 2 Sets
Build 4 Sets
P.5

12 Attaching Rear arms
12
LR
1.2x3PB x2
2x4KM x2
2x4PB x2
2x12mm
Camber arm
Linkage Ball D
Linkage Ball E
2x4x0.5
washer
2x4KM
2x12mm
2x4PB
Rear
Front
13 Attaching Grease shock
13
LR Front
Rear
2x4KB x4
Front Shock Tower (+2.5)
Rear Shock Tower (0)
Shock Tower (+2.5)
Linkage Ball 4mm
(AMZ011)
2x4KB
Shock Tower (0)
2x4KB
0.6mm
1.2x3PB
Sping
Sping
oil
oil
Linkage Ball 4mm
(AMZ011)
P.6 oil We recommend to apply #30000
Different Grease to the shocks.

2x6KB x2
15 15 Attaching Front Body Mount
2x4KB x3
2x4PB x2
14 14 Attaching other parts
2x4KB
2x4PB
2x4PB
Double-sided Tapes
Speed controller w/ RX
2x6KB
Not included
Trim this part to avoid the touch of
front belt
P.7
Caution:
Trim the front body
mount a little bit
to give space for
the front belt.

www.rcatomic.com
End of Assembly