Attacus AT-500 User manual

RUN/WALK 1-1
RUN/WALK 1-2
FATBURN
MOUNTAIN RANGE
HIKING TRAIL
CLIMBING
SPEED UP
Unit dimensions:
Unit weight:
Maximum weight
carrying capacity:
Belt size:
Motor:
Voltage:
Speed:
Incline:
Length: 188 CM (74.02 in)
Width: 89 CM (35.04 in)
Height: 135 CM (53.15 in)
113.5 KG (250.2 lb)
130 KG (287 lb)
51 x 140 CM (20 x 55 in)
1.75 HP
110V 220V，50/60Hz
0.8~18 (KM/HR)
10 %
Exercise programs
Hand held heart
rate monitor:
Wireless receiving
device:
Fan:
Audio:
YES
5 kHz, Bluetooth and ANT+
YES
Bluetooth audio device/High
quality audio
MANUAL
INTERVAL 1-1
INTERVAL 1-2
WEIGHT LOSS
HILL CLIMB
CROSS COUNTRY
TARGET LAP
TARGRT STEP
BASIC HRC 80/60%
P01
P00
P02
P03
P04
P05
P06
P07
P08
P09
P10
P11
P12
P13
P14
P15
Basic specifica on
Basic equipment
8
1) Please move and transport the treadmill carefully. Put the box on a level surface. Only open the box with its
surface on top. It is recommended to put a protec ve mat on the floor.
2) Unpack and assemble the treadmill at the planned loca on to avoid unnecessary transporta on. Pay great
aen on when unfastening cable e that used for packing or fixing to avoid accidental bounce.
3) Please follow assembly procedure to assemble the treadmill a er unfastening cable e. Please fold the machine
to upright and make sure the pin of hydraulic li is securely locked if you need to li or move it. DO NOT try to
crane the machine.
4) DO NOT try to li or move the machine with a single part or stand. (Refer to “Move/transport the treadmill” on
P.14 for informa on related to moving the product.)
Enclosed tools
Hex wrench
Phillips screwdriver
No ces and safety ps
Assembly parts
Console x 1
Display Console x 1
Upright x 2(L & R)
Upright safety cover x 2(L & R)
Accessory pack
Hardware parts box x 1
Safety key x 1
Power cable x 1
Line-level audio adapter x 1
Silicon oil x 1
When assembling, make sure all nuts, screws and parts are posi oned and lightly locked before
proceeding to the next step. A er the assembly is completed, make sure all screws are securely
locked. DO NOT arbitrarily decrease the quan ty of assembling screw.
Several parts are lubricated before delivery to facilitate assembly. DO NOT arbitrarily wipe offthe
lubricant. You can use lubricant to assemble parts when facing any difficulty. It is recommended
to use the lithium base grease for bike.
Several parts are very heavy; DO NOT try to assemble the machine on your own. These heavy
parts may fall and lead to personnal injury. Strongly recommend to have more than 2 persons for
assembly.
•
•
•
Please follow assembly instruc ons to li or move the treadmill. DO NOT arbitrarily li or take out
the product from the package.
Fail to following above instruc ons may lead to personnal injury and machine damage. Please
pay great a en on to these instruc ons.
•
•
Please contact the distribu-
tor or the Warranty card for
technical support if any part
is missing or you have any
ques on.
Before Assembly
Troubleshoo ng of The Heart Rate
Please correctly wear the heart rate monitor(op onal accessories) according following steps. The posi on and ghtness will influence the accuracy of
detec on:
1) Adjust the strap length to fit ghtly but comfortably around your chest and avoid any slide during workout.
2) Make sure the fastener of heart rate monitor sensor is securely fastened.
3) Wet the electronic sensing area with clean water.
4) Wear your monitor under your chest.
5) Make sure the monitor is worn in right direc on. The logo must be at exact center of your chest to ensure successful and accurate detec on.
Please follow the above-men oned steps to wear the heart rate monitor correctly and achieve the most accurate detec on during workout.
The heart rate monitor is an assis ve devices instead of a medical equipment. Please select the appropriate exercise intensity according to
your physical condi on.
Wearable connec on
Fluorescent lamps, computers or large motors may interfere the detec on and lead to inaccurate heart rate reading:
1)Your heart rate reading may be unstable under following condi ons:
•The holds to heart rate sensor bar are too ght. Please hold the heart rate sensor bar with appropriate stress.
•Mo on and vibra on caused by con nuous hold to the heart rate sensor bar during the workout.
•Users with heavy breathing during the workout or thick skin on the palms.
•Wearing accessories like rings during the workout can lead to inaccurate detec on.
•Dry, moist or cold hands can influence the accuracy of detec on. It is recommended to keep moderate moisture on your hands and rub your hands for
keeping warm.
•Users with serious asthma, or atherosclerosis or peripheral arterial occlusive disease.
2)Unstable heart rate reading or the machine fails to display heart rate on the console display overview :
•Please make sure your skin have contact with the heart rate monitor. We recommend to wet the sensing area with clean water and try pairing again a er
wearing.
•Make sure the fastener of heart rate monitor sensor is securely fastened.
•Make sure the distance between the device and the receiver (on the upper right of onsole display overview) is within 300cm (118 in).
•Make sure the ba ery of heart rate monitor sensor is fully charged.
•Dry sensing area or loose strap of the heart rate monitor can effect detec on. It is necessary to maintain moderate moisture on the sensing area. Please
also make sure the strap fits your chest ghtly but comfortably.
Troubleshoo ng
Speaker
Console display overview/opera ng panel
Rack
Quick key panel
Power switch/power cord
Upright
Upright safety cover
Hydraulic li system
Fan
Magazine rack
Handrail quick key
Handrail
Safety key
Heart rate sensor bar
Motor safety guard
Side rail
Belt
Non-skid mat
Belt tension adjus ng screw
Caster
Water bo le holder
3
Grounding Instruc on
The power socket of this product contains a grounding conductor. This socket must be inserted into the outlet via the power cord with grounding latch. The plug must
be plugged into an appropriate outlet that is properly installed and grounded in accordance with local codes and ordinances.
This product uses a rated voltage of 220V or 110V and comes with a three-pin power cord as shown in the following illustra on.
If the grounding outlet is not available, please use grounding adapter to connect this plug to the two-pin outlet. Please have qualified electrician install the
grounding outlet correctly before using the adapter. Please connect the grip or similar adapter extension to the ground and fix with the metal screw whenever
the adapter is used. Refer to the following illustra on.
Do determine the power cord is electrically related for 220V or 110V by checking the specifica on label or specifica on. Please make sure
the cord is connected to the plug with correct voltage. DO not use the power cord via adapter or extension cord to avoid of any component damage or personnel
injury caused by sudden voltage changes such as voltage surges and spikes.
Power cable
Three-pin outlet
Power cable
Grounding adapter
Metal grounding screw
Two-pin outlet
The above illustra ons only show three-pin power code power cord and outlet or two-pin outlet and grounding adapter. The type of
three-prong, two-prong and grounding adapter may vary in different countries. The enclosed power cord will be provided according to local
regulaonsof each country.
Make sure the power cord is connected to the outlet with correct voltage. DO NOT connect the power cord to the outlet via voltage adapter
or extension cord to avoid accidental current that may damage component and lead to personnel injury.
•
•
Grounding
Outlet
Qty
4
6
8
4
Console cable
Hex wrench
A
A
DC
C
A
D
C
C
B
C
B
C
B
C
B
DC
A
D
Console cable
Hex wrench
A
A
DC
C
A
D
C
C
B
C
B
C
B
C
B
DC
A
D
1) Open hardware pack 1.
2) Connect the lead wire to the console cable, pull them through the
right upright of the console, pull out the lead wire from the right upright
and then fix the console cable to the top of upright. Please remove the
lead wire then.
3) Put the right upright on the frame.
4) Use part A, C & D (2 of each) and connect the upright to the frame.
Make sure all screws and washers are well posi oned and lock them
lightly.
5) Use part B & C (2 of each) and connect the upright to the frame. Make
sure part B & C are well posi oned and lightly locked. Confirm all screws
and washers on the right side are posi oned.
6) Repeat step 3~5 to complete the assembly of the le upright.
Hardware pack for step 1
Descrip on
Parts
A
B
C
D
TypeIllustra on
Bu on Head Socket Bolt (55L)
Bu on Head Socket Bolt (20L)
Flat washer (Ø23)
Split washer (Ø18)
Screw
Screw
Washer
Washer
• Put the console strut on the frame with great care to avoid any damage to the console cable.
• DO NOT lock the screw ghtly before you finish step 3.
Step 1 of Assembly Procedure
1) Take the le and right upright safety covers.
2) Put the protec ve cover through the right upright safety cover carefully.
3) Put the protec ve cover through the le upright safety cover carefully.
Step 2 of Assembly Procedure
12
Console cable
Console connec ng cable
Hex wrench
Phillips screwdriver
A
A
D
D
D
D
A
A
A
A
A
A
C
C
C
C
B
B
B
B
1) Open hardware pack 3.
2) Connect the console cable to the connec ng cable on the console.
3) Put the console on the uprights carefully.
4) Use part A & C (2 of each for le and right side), connect the upright
to the frame. Make sure all screws and washers are well posi oned and
lock them lightly.
5) Use part A & D (2 of each for le and right side), connect the upright
to the frame. Make sure all screws and washers are well posi oned and
lock them lightly.
6) Li the uprights safety cover of the upright on both sides and lock all
screws at the lower side of upright ghtly.
7) Use part B (2pcs for le and right side) and lock the uprights safety
cover of the upright safety cover on both sides ghtly.
8) Lock all screws ghtly.
Hardware pack for step 3
QtyDescrip onParts
A
C
TypeIllustra on
8
4
Bu on Head Socket Bolt (20L) Screw
Washer
B4Truss head Phillips screw (10L)Screw
D4
Flat washer (Ø23)
Curved washer (Ø23)Washer
• Please assemble the console with great care. Make sure no wire is pressed orbent to avoid any damage.
• Make sure all screws are well posioned and lightlylocked. DO NOT lock thescrew ghtly when posioning to ensure a smooth assembly.
Step 3 of Assembly Procedure
AT500 Specifica on

er
Workout intensity
4
5
10
9
7
3
2
8
6
Clear
Fan switch
ANT+
display/pairing
Bluetooth
display/pairing
Quick incline
bu on
Start
Program UP/DOWN
Incline UP/DOWN
Speed UP/DOWN
Conflrm
Workout data
display
Stop
Safety
key
Keypad
11
12
13
20
15
16
Quick speed bu on
on handrail
17
18 19
Quick incline
bu on
14
3.5mm
Audio Jack
(AUX IN)
Quick incline
bu on on handrail
1Digital Screen
1) Time : display in the format of HH: MM: SS. Display your
workout me or con nuous workout me.
2) Slope : display in level. Display the slope when you are doing a
fast walk or running on the treadmill.
3) Speed : display in km or mile. Display the slope when you are
doing a fast walk or running on the treadmill.
4) Lap & Program : display the lap or program selec on.
5) KM & Mile : display the distance in digital clock in km or mile.
6) STEP : display the step detected when running in le and right
feet.
7) Pace & Step : can switch the display of your current Pace,
steps(Step1), step frequency(Step2), and current length(Step3).
8) Distance & Slope : can switch the display of total distance or accumulat-
ed slopeof your workout.
9) Total calories & Calories per hour : can switch the display current total
calories burned or calories burned per hour.
10) Heart beat & Workout metabolic rate : can switch the display of
current heartbeat or convert the heart rate into metabolic rate to show
workout intensity.
11) Bluetooth connec on : when this indicator is on, the heart beat is the
valuedetected byBluetooth on the connected wearabledevice.
12) ANT+ connec on : when this indicator is on, the heart beat is the value
detected by ANT+ on the connected wearable device.
13) Smart device connec on : when this indicator is on, it means the
smart device is connected to the treadmill via Bluetooth.
14) Bluetooth Speaker connec on : when this indicator is on, it means the
Speaker is connected to the treadmill via Bluetooth.
Press
Move
Transport
•
•
There is a safety lock on the hydraulic li under the machine. If you like to put down the deck, please gently kick the orange pin of hydraulic
li and press deck slightly, then lower the deck carefully on the ground.
The treadmill is very heavy. Please ask another person to move or transport it with you. Before moving or transpor ng, make sure the deck is
folded and the pin of hydraulic li is fixed. DO NOT try to arbitrarily move or transport the treadmill on your own. Fail to follow above instruc ons
may lead to personnel injury and machinedamage. Please pay great a en on to these instruc ons.
Move / Transport the Treadmil
Please hold the frame at the rear side of machine or under back roller secure-
ly and upright the deck carefully un l the pin of the hydraulic li is locked.
Please put down the deck carefully and make sure it does not fall. To unlock
the fixa on, please hold the frame at the rear side of machine or under back
roller securely and lightly kick the orange pin of hydraulic li and press deck
slightly. Put the deck on the floor carefully.
How to fold
The treadmill comes with two sets of casters. Please fold the treadmill and
make sure the deck is fixed before moving it. Hold the handrails ghtly, make
the machine lean backward and move it. A empt to move or transport the
treadmill without a folded and fixed deck can result in personnel injury or
machine damage.
How to move
The treadmill comes with two sets of casters. Please fold the treadmill and
make sure the deck is fixed before moving it. Hold the handrails ghtly, make
the machine lean backward and move it. The treadmill is very heavy. DO NOT
arbitrarily move it unless it’s necessary.
How to transport “LUBE” will be displayed on the digital screen when the accumulated hour reaches 100
hours or distance of 1000km as a reminder of belt maintenance. Please press “STOP” or
remove the safety switch and maintain the belt under standby status. A er finishing belt
maintenance, please press “START”, “SPEED UP” and “SPEED DOWN” simultaneously to
clear the accumulated hours or kilometers. For belt maintenance, apply the silicon oil
(the whole bo le) to the inner side of belt. A er the oil is fully applied to the belt, please
operate with high speed (10KM) for 10 minutes to make the oil spread evenly on the belt.
The belt slides to the le :
When the belt slides to the le , please fine-tune
the rear le screw in a clockwise direc on to the
right under high speed opera on (10KM). Repeat
above steps un l the belt moves back to the
center if the belt s ll shi s offa er 30~60 seconds
under high speed opera on.
The belt slides to the right
When the belt slides to the right, please fine-tune
the rear right screw in a clockwise direc on to the
right under high speed opera on (10KM). Repeat
above steps un l the belt moves back to the
center if the belt s ll shi s offa er 30~60 seconds
under high speed opera on.
The posi on of belt is adjusted before shipment. However, some mes the belt may shi offcenter during transporta on.
To adjust a slipping belt, please use the enclosed hex wrench turn the screws at rear (both sides) of the deck to the right by 90 degrees un l no slippage occurs.
Make sure the belt is not moving while adjus ng the screw.
DO NOT adjust the belt when the machine is opera ng. A ght belt may bring extra load to the frame and electronic components and
therefore should be avoided.
When the belt is adjusted to the center, please test with the speed of 10KM for 30~60 seconds to check if the belt is appropriately
ghtened and if any devia on occurs. Keep your fingers, hair and clothing away from the belt when tes ng.
•
•
Adjust / Maintain the Belt
Belt maintenance
Belt adjustment
The belt stays at the center
200CM
100CM
100CM
30~50CM
Place the machine on a level ground. Clearance requirement: 200cm at the
rear, 100cm at le and right sides and 30~50 cm at the front. DO NOT place
the machine in front of the indoor/outdoor vent, in the garage, in the open
yard, outdoors, or near the water supply.
The treadmill is an equipment for aerobic exercise that can facilitate weight loss, cardiopulmonary func on enhancement, and muscle tension and basic metabol-
ic rate improvement. Good exercise habits are helpful for achieving these goals. This product can help you to build healthy exercise habit at home.
Please evaluate your physical condi on before the exercise and pay a en on to following advice:
1) Do warm-up before you start to run. Warm-up can help stretching your muscles and avoid sports injury.
2) Wear sneakers with a gum sole. This can effec vely relieve the pressure to knees during the workout.
3) Please focus on your workout and please a ach the safety clip to your clothing, please also pay highly a en on to your safety to use smart device or any media
player to watch TV/magazine during workout as this may lead to sport injury caused by poor posture.
4) Gradually increase your running speed. Release your grip on the handrails at a comfortable speed.
5) We recommend to limit your exercise to 30~60 minutes. Excessive exercise may result in knee injury or other poten al injuries.
6) Decrease your speed from a fast walk to a slow walk for a gradual recovery when your workout is coming to the end. DO NOT leave the deck immediately a
the workout to avoid dizziness.
The treadmill is a simple and efficient training equipment and your shortcut to pursue a
healthy lifestyle.
DO NOT start the machine with your feet on the belt. Please stand on foot rails when star ng the machine. Start walking on the treadmill only
when the belt starts moving. DO NOT start the machine with the fast run speed. DO NOT try to jump on the machine.
Prepara ons before Use
Treadmill loca on
Regula ng foot pad
The machine will not start opera ng un l the safety key is correctly inserted into the port. Always a ach the safety key to your clothing during workout. The
safety key is the device to ensure your safety, the emergency stop cu ng offthe power in case runner accidentally falls down on the treadmill. Please check every
2 weeks to ensure the safety key work func onally.
Start with slow speed and gradually increase the speed to a comfortable level. DO NOT let the machine run by itself. Please pull out the safety switch, turn the
power offand unplug the power cord when not in use. Please start the machine with slow speed. Stand on foot rails first and try to turn your trunk or lean
forward. Please stop using any sport equipments including the treadmill immediately once you feel any dizziness, pain, exhaus on or difficult breathing.
Level the machine before use. When the
treadmill loca on is determined, please adjust
the regula ng foot pad on the deck and fix it
aer adjus ng to the best posi on. Make sure
the deck is adjusted to an appropriate height
before use.
Make sure the power cord of treadmill is correctly plugged. The indicator should light up when the power is on. The digital screen will light up a er the beep; 3
seconds a er the machine enters standby status, you can press “Quick Start” twice to proceed to fast exercise or select “PROGRAMS” and the machine will start
to operate at low speed.
DO NOT use the machine without using the safety clip. Please a ach the safety clip to your clothing before the workout. Try to pull out
the safety switch and make sure the clip does not fall from clothing.
Damaged power cord or outlet may lead to irregular machine opera on and personnel injury. Please stop the opera on or workout imme-
diately if this occurs.
•
•
Leveling
Turn on the power
Safety key
Correct use
• Keep children under 13 or pets always away from the treadmill at least 3M (10 .) at all mes. Children under 13 are not allowed to use this machine.
• The use by children between 13~18, seniors over 65 or disabled people must be under the surveillance of other adults to avoid any danger.
• Please follow instruc ons in this manual when using the machine.
• DO NOT use parts other than manufacturer or distributor recommenda on to avoid personnel injury.
• Please stop using the machine immediately and contact maintenance staffif you encounter power cord or plug damage or irregular opera on caused by
accidental drop, impact or soaking in the water.
• Put the power cord away from the surface with high temperature. DO NOT li the machine with the power cord or use the power cord as a handrail.
• Make sure the vent of the machine is clean before the workout. Remove substances like co on wadding and hair.
• DO NOT put, drop or insert any object in openings as it may result in electric shock. Alatech is not responsible for any damage rising from failure to follow
instruc ons.
• The motor controller generate heat. DO NOT use any spray near this area as it may result in combus on.
• Turn offall equipment and power and unplug the power cord when the workout is completed or the connec on is removed.
• Only use this machine in a place with controlled temperature. DO NOT use in the garage, porch, bathroom, kitchen, carport or outdoors. We is not responsible
for any damage rising from failure to follow instruc ons.
• This treadmill is for ordinary household use ONLY. The warranty does not cover applica ons in business place, rental service, school or organiza on.
• Specific sole materials of shoes may generate sta c electricity. To avoid electric shock, please wear sneakers with gum sole instead of plas c or insulated one.
• Before using the machine, please DO consult your physician and evaluate by physical exam, especially for users are over age 45, users with pre-exis ng health
problems from family history such as high pressure or heart disease, users with high cholesterol or obesity, smokers, expectant mother, and users have not done
a workout regularly over one year.
Please abide by following instruc on to avoid burn, fire, electric shock or injury to persons:
This product is for indoor use only. Please pay a en on to room temperature and humidity. If the machine is placed in the environment with
unstable temperature and humidity, it is recommended to warm-up the machine to ambient temperature before the workout. Fail to follow
this instruc on may lead to early damage to electronic components.
To Ensure Your Safety
Treadmill Serial Number
Please always make sure that serial number on treadmill is same as warranty card indicated. If not, please do not assemble machine and contact
Alatech’s service center or distributor for further assistance. If maintenance needed, the serial number on machine and warranty card must be
the same, if inconsistent serial number is found, we will not provide warranty.
Ensure your warranty by following no ces:
1) The warranty will be invalid if there is no distributor stamp on warranty card or the content is incomplete. However, this warranty does not
cover following condi ons:
•When customers can provide original invoice or proof of purchase
•When the related proof of purchase can be provided by document
2) Please bring this warranty card when you need maintenance services.
3) Please contact approved distributors or service loca ons while your warranty is s ll valid.
4) Please keep this warranty card in a secure place.
Assembly Instruc on
Please follow the assembly instruc ons and steps in this manual and make sure all parts are securely fastened. Fail to follow the instruc ons
may lead to loose parts on the treadmill. Loose parts can result noise or may cause personnel injury. Please thoroughly read the assembly
instruc on to avoid any damage to the treadmill.

• Never use the treadmill before securing the safety key clip to your clothing.
• Stop exercising immediately and consult your physician before con nuing, if you experience any kind of pain, including but not limited to chest pains, nausea,
dizziness, or shortness of breath.
• Maintain a pace you feel comfortable during the workout. DO NOT run with extremely high speed.
• Do not wear clothes that might catch on any part of the treadmill.
• Always wear athle c shoes while using this equipment.
• At no me should more than one person be on treadmill while in opera on.
• Do not jump on the treadmill or stand on plas c parts such as Motor safety guard , Upright safety covers or rear cover, to avoid any improper use or ac on.
• This treadmill should not be used by persons weighing more than Max. User Weight. Failure to comply instruc ons will void the warranty.
• Disconnect all power before maintenance, moving or folding the treadmill.
• Please use a wet cloth to clean the surface for machine maintenance. DO NOT use any detergent.
• The treadmill should never be le una ended when the power is plugged in. Always UNPLUG from outlet when NOT in use.
• DO NOT cover the machine with blanket or fabric. The blanket or fabric may cause overheat and lead to fire, electric shock or other personnel injuries.
• Make sure the machine is connected to the correct outlet. Failure to comply instruc on will void the warranty.
• Please place the machine on a level ground. DO NOT place and use the machine on an uneven ground.
Please abide by following instruc on to avoid burn, fire, electric shock or injury to persons:
• Please turn offthepower and unplugthepower cord immediately a er finishing the workout.
• Always turn offthepower and unplugthepower cord before cleaning, performingmaintenance, move or taking offparts.
Treadmill Precau ons
• Keep children under 13 or pets always away from the treadmill at least 3M (10 .) at all mes. Children under 13 are not allowed to use this machine.
• The use by children between 13~18, seniors over 65 or disabled people must be under the surveillance of other adults to avoid any danger.
• Please follow instruc ons in this manual when using the machine.
• DO NOT use parts other than manufacturer or distributor recommenda on to avoid personnel injury.
• Please stop using the machine immediately and contact maintenance staffif you encounter power cord or plug damage or irregular opera on caused by
accidental drop, impact or soaking in the water.
• Put the power cord away from the surface with high temperature. DO NOT li the machine with the power cord or use the power cord as a handrail.
• Make sure the vent of the machine is clean before the workout. Remove substances like co on wadding and hair.
• DO NOT put, drop or insert any object in openings as it may result in electric shock. Alatech is not responsible for any damage rising from failure to follow
instruc ons.
• The motor controller generate heat. DO NOT use any spray near this area as it may result in combus on.
• Turn offall equipment and power and unplug the power cord when the workout is completed or the connec on is removed.
• Only use this machine in a place with controlled temperature. DO NOT use in the garage, porch, bathroom, kitchen, carport or outdoors. We is not responsible
for any damage rising from failure to follow instruc ons.
• This treadmill is for ordinary household use ONLY. The warranty does not cover applica ons in business place, rental service, school or organiza on.
• Specific sole materials of shoes may generate sta c electricity. To avoid electric shock, please wear sneakers with gum sole instead of plas c or insulated one.
• Before using the machine, please DO consult your physician and evaluate by physical exam, especially for users are over age 45, users with pre-exis ng health
problems from family history such as high pressure or heart disease, users with high cholesterol or obesity, smokers, expectant mother, and users have not done
a workout regularly over one year.
Please abide by following instruc on to avoid burn, fire, electric shock or injury to persons:
This product is for indoor use only. Please pay a en on to room temperature and humidity. If the machine is placed in the environment with
unstable temperature and humidity, it is recommended to warm-up the machine to ambient temperature before the workout. Fail to follow
this instruc on may lead to early damage to electronic components.
To Ensure Your Safety
Manufacture address: No.405 Tongxin Road, Tongxiang Economic
Development Zone, Zhejiang 314500, China
TEL: [phone]
Warranty card
Assembled on Y M D
Model number
Serial number
Dealer Stamp
Please keep this warranty card.
The following precautions can guarantee your warranty rights:
1) If the warranty card is not stamped with the company seal
( or dealer) or the contract is incomplete, it may loss the warranty rights,
the following conditions are not within this limit:
‧ Submit original invoice or proof of purchase
‧ Distribution document that can provide relevant proof of purchase
2) Please show this warranty card when requiring repair service.
3) During the warranty period, please contact the dealer or
maintenance base authorized by the company.
4) You are given only one original copy of this warranty card please
preserved it properly.