Treadmill Serial Number
Please always make sure that serial number on treadmill is same as warranty card indicated. If not, please do not assemble machine and contact
Alatech’s service center or distributor for further assistance. If maintenance needed, the serial number on machine and warranty card must be
the same, if inconsistent serial number is found, we will not provide warranty.
Ensure your warranty by following no ces:
1) The warranty will be invalid if there is no distributor stamp on warranty card or the content is incomplete. However, this warranty does not
cover following condi ons:
•When customers can provide original invoice or proof of purchase
•When the related proof of purchase can be provided by document
2) Please bring this warranty card when you need maintenance services.
3) Please contact approved distributors or service loca ons while your warranty is s ll valid.
4) Please keep this warranty card in a secure place.
Assembly Instruc on
Please follow the assembly instruc ons and steps in this manual and make sure all parts are securely fastened. Fail to follow the instruc ons
may lead to loose parts on the treadmill. Loose parts can result noise or may cause personnel injury. Please thoroughly read the assembly
instruc on to avoid any damage to the treadmill.
Press
Move
Transport
Move / Transport the Treadmil
There is a safety lock on the hydraulic li under the machine. If you like to put down the deck, please gently kick the orange pin of hydraulic
li and press deck slightly, then lower the deck carefully on the ground.
The treadmill is very heavy. Please ask another person to move or transport it with you. Before moving or transpor ng, make sure the deck is
folded and the pin of hydraulic li is fixed. DO NOT try to arbitrarily move or transport the treadmill on your own. Fail to follow above instruc ons
may lead to personnel injury and machine damage. Please pay great a en on to these instruc ons.
•
•
Please hold the frame at the rear side of machine or under back roller secure-
ly and upright the deck carefully un l the pin of the hydraulic li is locked.
Please put down the deck carefully and make sure it does not fall. To unlock
the fixa on, please hold the frame at the rear side of machine or under back
roller securely and lightly kick the orange pin of hydraulic li and press deck
slightly. Put the deck on the floor carefully.
How to fold
The treadmill comes with two sets of casters. Please fold the treadmill and
make sure the deck is fixed before moving it. Hold the handrails ghtly, make
the machine lean backward and move it. A empt to move or transport the
treadmill without a folded and fixed deck can result in personnel injury or
machine damage.
How to move
The treadmill comes with two sets of casters. Please fold the treadmill and
make sure the deck is fixed before moving it. Hold the handrails ghtly, make
the machine lean backward and move it. The treadmill is very heavy. DO NOT
arbitrarily move it unless it’s necessary.
How to transport
“LUBE” will be displayed on the digital screen when the accumulated hour reaches 100
hours or distance of 1000km as a reminder of belt maintenance. Please press “STOP” or
remove the safety switch and maintain the belt under standby status. A er finishing belt
maintenance, please press “START”, “SPEED UP” and “SPEED DOWN” simultaneously to
clear the accumulated hours or kilometers. For belt maintenance, apply the silicon oil
(the whole bo le) to the inner side of belt. A er the oil is fully applied to the belt, please
operate with high speed (10KM) for 10 minutes to make the oil spread evenly on the belt.
The belt slides to the le :
When the belt slides to the le , please fine-tune
the rear le screw in a clockwise direc on to the
right under high speed opera on (10KM). Repeat
above steps un l the belt moves back to the
center if the belt s ll shi s offa er 30~60 seconds
under high speed opera on.
The belt slides to the right
When the belt slides to the right, please fine-tune
the rear right screw in a clockwise direc on to the
right under high speed opera on (10KM). Repeat
above steps un l the belt moves back to the
center if the belt s ll shi s offa er 30~60 seconds
under high speed opera on.
The posi on of belt is adjusted before shipment. However, some mes the belt may shi offcenter during transporta on.
To adjust a slipping belt, please use the enclosed hex wrench turn the screws at rear (both sides) of the deck to the right by 90 degrees un l no slippage occurs.
Make sure the belt is not moving while adjus ng the screw.
DO NOT adjust the belt when the machine is opera ng. A ght belt may bring extra load to the frame and electronic components and
therefore should be avoided.
When the belt is adjusted to the center, please test with the speed of 10KM for 30~60 seconds to check if the belt is appropriately
ghtened and if any devia on occurs. Keep your fingers, hair and clothing away from the belt when tes ng.
•
•
Adjust / Maintain the Belt
Belt maintenance
Belt adjustment
The belt stays at the center
200CM
100CM
100CM
30~50CM
Place the machine on a level ground. Clearance requirement: 200cm at the
rear, 100cm at le and right sides and 30~50 cm at the front. DO NOT place
the machine in front of the indoor/outdoor vent, in the garage, in the open
yard, outdoors, or near the water supply.
The treadmill is an equipment for aerobic exercise that can facilitate weight loss, cardiopulmonary func on enhancement, and muscle tension and basic metabol-
ic rate improvement. Good exercise habits are helpful for achieving these goals. This product can help you to build healthy exercise habit at home.
Please evaluate your physical condi on before the exercise and pay a en on to following advice:
1) Do warm-up before you start to run. Warm-up can help stretching your muscles and avoid sports injury.
2) Wear sneakers with a gum sole. This can effec vely relieve the pressure to knees during the workout.
3) Please focus on your workout and please a ach the safety clip to your clothing, please also pay highly a en on to your safety to use smart device or any media
player to watch TV/magazine during workout as this may lead to sport injury caused by poor posture.
4) Gradually increase your running speed. Release your grip on the handrails at a comfortable speed.
5) We recommend to limit your exercise to 30~60 minutes. Excessive exercise may result in knee injury or other poten al injuries.
6) Decrease your speed from a fast walk to a slow walk for a gradual recovery when your workout is coming to the end. DO NOT leave the deck immediately a er
the workout to avoid dizziness.
The treadmill is a simple and efficient training equipment and your shortcut to pursue a
healthy lifestyle.
DO NOT start the machine with your feet on the belt. Please stand on foot rails when star ng the machine. Start walking on the treadmill only
when the belt starts moving. DO NOT start the machine with the fast run speed. DO NOT try to jump on the machine.
Prepara ons before Use
Treadmill loca on
Regula ng foot pad
The machine will not start opera ng un l the safety key is correctly inserted into the port. Always a ach the safety key to your clothing during workout. The
safety key is the device to ensure your safety, the emergency stop cu ng offthe power in case runner accidentally falls down on the treadmill. Please check every
2 weeks to ensure the safety key work func onally.
Start with slow speed and gradually increase the speed to a comfortable level. DO NOT let the machine run by itself. Please pull out the safety switch, turn the
power offand unplug the power cord when not in use. Please start the machine with slow speed. Stand on foot rails first and try to turn your trunk or lean
forward. Please stop using any sport equipments including the treadmill immediately once you feel any dizziness, pain, exhaus on or difficult breathing.
Level the machine before use. When the
treadmill loca on is determined, please adjust
the regula ng foot pad on the deck and fix it
aer adjus ng to the best posi on. Make sure
the deck is adjusted to an appropriate height
before use.
Make sure the power cord of treadmill is correctly plugged. The indicator should light up when the power is on. The digital screen will light up a er the beep; 3
seconds a er the machine enters standby status, you can press “Quick Start” twice to proceed to fast exercise or select “PROGRAMS” and the machine will start
to operate at low speed.
DO NOT use the machine without using the safety clip. Please a ach the safety clip to your clothing before the workout. Try to pull out
the safety switch and make sure the clip does not fall from clothing.
Damaged power cord or outlet may lead to irregular machine opera on and personnel injury. Please stop the opera on or workout imme-
diately if this occurs.
•
•
Leveling
Turn on the power
Safety key
Correct use
1) Time : display in the format of HH: MM: SS. Display your
workout me or con nuous workout me.
2) Slope : display in level. Display the slope when you are doing a
fast walk or running on the treadmill.
3) Speed : display in km or mile. Display the slope when you are
doing a fast walk or running on the treadmill.
4) Program : display the program selec on. when you select the
desired program, the program name will be showed on the
screen accordingly.
5) KM & Mile : display the distance in digital clock in km or mile.
6) Reminds you to apply silicon oil: “LUBE” will be displayed
flickering on the digital screen either the accumulated hours
reach 100 hours or accumulated distances reach 1000km
7) Pace & Step : can switch the display of your current Pace,
steps(Step1), step frequency(Step2), and current length(Step3).
8) Distance & Slope : can switch the display of total distance or accumulat-
ed slope of your workout.
9) Total calories & Calories per hour : can switch the display current total
calories burned or calories burned per hour.
10) Heart beat & Workout metabolic rate : can switch the display of
current heartbeat or convert the heart rate into metabolic rate to show
workout intensity.
11) Bluetooth connec on : when this indicator is on, the heart beat is the
value detected by Bluetooth on the connected wearable device.
12) ANT+ connec on : when this indicator is on, the heart beat is the value
detected by ANT+ on the connected wearable device.
13) Smart device connec on : when this indicator is on, it means the
smart device is connected to the treadmill via Bluetooth.
14) Bluetooth Speaker connec on : when this indicator is on, it means the
Speaker is connected to the treadmill via Bluetooth.
3
9
2
Digital screen 1
11
Workout intensity display
18
10
Fan switch
8ENTER
START
Quick incline bu on
on handrail
13 PROGRAMS UP/DOWN
5INCLINE UP/DOWN
7Quick incline bu on
Quick speed
bu on
6
4SPEED
UP/DOWN
12
3.5mm
Audio Jack
(AUX IN)
STOP 15 Quick speed
bu on on
handrailBluetooth display/pairingSafety key
16
Exercise data
display
14
17 ANT+ display/pairing
1) Digital screen: displays informa on such as the workout me, distance, calorie, heart rate, step, slope and speed.
2) START: press this bu on to start your workout, or start the exercise a er selec ng the program. Press to restart the exercise a er the pause.
3) STOP: press this bu on to pause and press it again to stop the exercise and collect the data. Press this bu on to return to the previous program when se ng
program value.
4) SPEED UP/DOWN: adjust the speed (unit=0.1, ranged from 0.8~20KM). It can also help you to enter quickly when se ng program value.
5) INCLINE UP/DOWN: gradually increase or decrease the slope (level unit=1, total=10%). It can also help you to enter quickly when se ng program value.
6) Quick speed bu on: quickly switch different speed values including warm-up and fast run.
7) Quick incline bu on: quickly switch different slope angles including warm-up and workout.
8) ENTER: press this bu on to proceed to the input of next data when se ng program value.
9) Bluetooth display/pairing: click this bu on can switch the heart rate of paired device. Long press this bu on to pair any wearable device.
10) ANT+ display/pairing: click this bu on can switch the heart rate of paired device. Long press this bu on to pair any wearable device.
11) Fan switch: turn on/offthe fan.
12) Audio Jack (AUX IN): connect your media player to the treadmill via the enclosed 3.5mm Audio Jack (AUX IN).
13) PROGRAMS UP/DOWN: select the program ; there are 13 programs available.
14) Exercise data display: exercise data switch; there are 4 types of data available, including Pace/steps(Step1)/step frequency(Step2)/current length(Step3),
distance/slope, total calorie/calorie per hour and heart rate/training intensity.
15) Quick speed bu on on handrail: located on the right handrail; increase or decrease the speed (unit=0.1KM, ranged from 0.8~20KM).
16) Quick incline bu on on handrail: located on the le handrail; gradually increase or decrease the slope (level unit=1, total=10%).
17) Safety key: you can turn on and operate the treadmill a er the switch is inserted. The machine is in emergency mode when the safety key is not inserted and
no opera on will be allowed.
18) Workout intensity display: display training intensity; determine current intensity according to the heart rate detected.
Please remove the transparent protec ve film on the opera ng panel before use.
Opera on Panel
You can choose to display your workout data by pressing “PACE/STEP” bu on. “Pace” shows target speed in minutes per mile (or kilometer),
“Step 1” shows steps, “Step 2” shows step frequency per minutes, or “Step 3” shows your current length, total 4 workout data.
