AUDIO TELEX TX6000 User manual

Description
The TX6000 is a high specification, single rack space, 6 channel mic/line mixer suitable for desk or rack mounting. The mixer is
designed to operate from both AC mains power as well as 24 volts DC.
Inputs
Six dual mic/line inputs are provided. The mic inputs are active balanced and feature 3 pin XLR female sockets. Each channel
also includes dual female RCA line/aux sockets.
Outputs
The TX6000 features a balanced line output via a 3 pin XLR male socket. A mono tape output is also available via dual female
RCA sockets. A 1/4” mono headphone socket is included on the front panel.
Controls
Front panel controls include a master output level control plus overall bass and treble controls. Individual channel level controls
are provided for all six inputs.
Metering
A 7 segment LED meter is provided for the master output. A power "on" neon is included on the power switch.
Muting
Muting is available via the optional VOX operated plug-in TX3010 or TX3014 VOX precedence cards. The TX3010 provides
priority from channel 1 over all other channels. The TX3014 provides two levels of priority. Channel 1 is the master mute channel
and overrides channels 2-6, whereas channels 2 will mute channels 3-6 only.
Tone Generators
The ATC5488 is an optional plug-in accessory providing 4 tones (Bell, Pre-Announce Chime, Alert and Evacuate). The evacuate
and alert tones comply with Australian Standard AS2220.1. The ATC5488 plugs into the main board via a 7 pin connector.
Activation wires can be fed through a rear panel slot below the 24V DC connector. Each tone can be activated by a simple
contact closure.
PhantomPower
Phantom power (18V DC) is provided on all mic inputs
EMC Compliance
The TX6000 is approved to Spectrum Management Agency EMC, C-Tick standards.
TX6000
6 Channel Mic/Line
Mixer
Audio Telex Communications Pty Ltd
www.audiotelex.com
Sydney [phone], Melbourne [phone], Brisbane [phone], Perth [phone]
Auckland [phone], Adelaide [phone], Hobart [phone]
A.C.N: 001 345 482

Architectural and Engineering Specifications
The mixer shall have 6 dual mic/line inputs. The microphone inputs shall be active balanced and feature 3 pin female XLR
sockets. The line inputs shall feature dual female RCA sockets.
Overall bass and treble controls shall be provided with front panel access. They shall provide 12dB cut or boost at 100Hz and
9dB cut or boost at 10kHz. The master section shall include a master level control and a 7 segment output level LED meter. The
master output shall be via a balanced 3 pin XLR male socket. The tape output shall be via dual female RCA sockets whilst a ¼"
headphone socket shall be provided on the front panel for monitoring purposes. The mixer shall have facilities for plug-in muting
cards as well as a 4 tone generator card.
The mixer shall be of high quality, suitable for both live and commercial applications. It should have ample headroom and a
frequency response of no less than 50Hz-15kHz (+/-3dB). Total Harmonic Distortion shall be no more than 0.08% at 1kHz. The
signal to noise ration shall be –78dB or better. Phantom power shall be available to all microphone inputs and shall be switchable
via an internal link. The unit shall be packaged in a 1 rack unit rugged metal chassis suitable for desk or rack mounting.
The mixer shall be an Audio Telex model TX6000.
Frequency Response
50Hz-15kHz (+/-3dB)
THD
Less than 0.08% @ 1kHz
S/N Ratio
-78dB (all channels at centre position)
Tone Controls
Bass @ 100Hz, Boost +12dB, Cut –12dB
Treble @ 10kHz, Boost +9dB, Cut –9dB
Inputs
6 dual mic/line. The mic inputs are active balanced with 3 pin
XLR female sockets (200-600 ohms). Maximum input level is
100mV. The line inputs are dual female RCA’s (47k ohms).
Maximum input level: 2.5V/10V
Input Sensitivity
Mic: 0.6mV @ 200 ohms
Line: 50mV @ 47k ohms
Channel 6 line input is 200mV (for CD player or similar high
level input)
Phantom Power
18V DC available on all mic channels (overall internal on-off
link)
TX6000 Specifications
Outputs
Master output is via a 3 pin male XLR socket (1.5v @ 600
ohms). Maximum output level: +20dB. Mono headphone
output via ¼" socket (3.5v @ 600 ohms). Mono tape output
via dual female RCA connectors (700mV @ 10 k ohms)
Controls
Level control per channel
Overall bass & treble controls
Master level control
Indicators
Power "on" neon
7 segment LED meter on master output
Power Source
AC: 240V-50Hz or 110V-60Hz (special order), 3 pin IEC
connector
DC: 24 volts via 2.1mm DC socket
Dimensions/Weight
44mm H x 482mm W x 250mm D (Chassis Dimensions
Only). 3kg
Power Consumption
7 vA
Audio Telex Communications Pt
y
Ltd
www.audiotelex.com
S
y
dne
y
(
02
)
9647 1411, Melbourne
(
03
)
9890 7477, Brisbane
(
07
)
3852 1312, Perth
(
08
)
9228 4222
Auckland
(
09
)
415 9426, Adelaide
(
08
)
8234 9444, Hobart
(
03
)
6228 6373
A.C.N: 001 345 482