AudioCodes MediaPack MP-263-DB User manual

AudioCodes MediaPack™Multimedia Home Gateway
MP-263-DB Quick Guide
2. Cabling
The basic cabling of your gateway is illustrated below:
Use only the supplied 12VDC +/-10%, tolerance, 2A, limited power source wall mount Class II power supply adapter.
Before connecting the gateway to power, ensure that the VAC ratings match, and that you have read the Compliance and
Regulatory Information at www.audiocodes.com/library.
1. Connect the gateway to the Internet using one of the following
connectivity methods:
WAN Ethernet: connect the WAN port (labeled WAN) to an
external modem, using a CAT 5 Ethernet cable.
xDSL:connect the xDSL port (labeled xDSL)to the
telephone socket, using an RJ-11 telephone cable.
Use minimum 26 AWG wire for connecting the xDSL
port to the public switched telephone network (PSTN).
2. Connect the Ethernet ports, labeled LAN 1-4 to your LAN
computers, using CAT 5 Ethernet cables.
3. Connect the telephone ports, labeled Phone 1-2 to analog
telephones, using RJ-11 telephone cables.
4. Connect the gateway to a standard 110/220 VAC electrical wall
outlet, using the supplied AC/DC power adapter.
5. When powered on, the gateway's Status LED turns on. When
initialization completes (~ 2 min.), the LED changes from red to
green. If the gateway is off, press the Power button located on
the rear panel to switch it on.
For wall mounting the gateway, refer to the
User's
Manual
.
Welcome
Thank you for purchasing AudioCodes MediaPack 263-DB
Multimedia Home Gateway (MP-263)!
This Quick Guide provides basic instructions on installing
and configuring your MP-263.
3. Installing the DECT Phone
1. On the handset, pull out the plastic tab jutting out from the battery compartment.
2. On the lower part of the gateway's front panel, remove the cover protecting the
connector for the handset cradle.
3. Attach the handset cradle to the unit by inserting it into the exposed groove and then
pushing it up so that it clicks on to the connector. Attach the removed cover to the
front of the cradle.
4. Place the handset in the cradle and leave to charge for at least 16 hours prior to initial
use.
1. Before Installing
Ensure that the shipped package contains the following items:
MediaPack Multimedia Home Gateway
1 x RJ-11 telephone cable
1 x RJ-45 Ethernet cable
12V AC/DC power adaptor (use only supplied)
DECT handset and cradle
If any item is missing, please contact your sales representative.
All manuals and user guides at all-guides.com

Notice
Information contained in this document is believed to be accurate and reliable at the time of printing. However, due to ongoing
product improvements and revisions, AudioCodes cannot guarantee accuracy of printed material after the Date Published nor can
it accept responsibility for errors or omissions. This document is subject to change without notice. Refer to the current Release
Notes that may be included with your documentation or hardware delivery. Updates to this document as well as software files can
be viewed by registered customers at www.audiocodes.com/downloads.
© Copyright 2013 AudioCodes Ltd. All rights reserved.
Date Published: April-18-2013
Document #: LTRT-18660
4. Registering the DECT Handset to the Base Unit
Before you can make or receive calls, you need to register the DECT handset to the gateway's base unit:
1. Press the Menu softkey, and then select the Registration icon.
2. Press the DECT LED button until (2-5 seconds) it starts flashing green; the base unit enters registration mode.
3. On the handset, select base unit, "Base 1" to which the handset must register; the registration process begins and
"Registering - Waiting" is displayed on the handset screen. When the handset identifies the base unit, it displays its radio
frequency identification.
4. Click the Accept softkey to confirm registration.
5. Configuring Network Parameters
1. Open a Web browser and then enter the following URL
address to access the gateway's embedded Web server
graphical user interface (GUI): http://mp263.home
2. Select the Web GUI display language and click Continue.
3. Define a new login username / password and click OK.
4. In the ‘Quick Setup’ page, select and define the Internet
connection type as instructed by your ITSP, and then
click OK. You are now connected to the Internet and can
proceed to configure VoIP parameters for
making and receiving voice-over-IP calls.
If there is no Internet connection, the Web GUI’s
Map View page (Home) displays a red icon after
the globe icon. Consult your ITSP for valid connection
parameters.
The gateway's default wireless (Wi-Fi) network name
(SSID)
comprises product name followed by "_" and
the six last characters of the MAC address in capital
letters (secured). For example, if the MAC address is
00:90:8F:2C:64:70, the SSID will be MP263_2C6470.
The password is the eight
last digits of the MAC
address, in capital letters, i.e., in this example:
8F2C6470.
6. Configuring VoIP Parameters
Before you can make VoIP calls, you need to register with an
Internet Telephony Service Provider (ITSP) and obtain account
and SIP Proxy server information
1. From the menu pane, click Voice Over IP; the ‘Voice
Over IP’ page appears in the right pane.
2. Click the Line Settings tab, mark check boxes of lines
that are connected to telephones (clear those not
connected), and then click Apply.
3. Click the Edit icon corresponding to the telephone
lines, and then in the ‘Line Settings’ page, configure the
parameters with values provided by your ISP.
4. Click the Signaling Protocol tab, and then select the ‘Use
SIP Proxy’ check box. In the ‘Proxy IP Address or Host
Name’ field, enter the ITSP’s proxy server IP address or
host name. Click OK to complete the VoIP configuration.
To verify successful registration with
the proxy
server, ensure that the Phone
LED is lit green or in
the Voice over IP tab (System Monitoring menu), the
entry ‘SIP Registration’ displays “Registered” for the
configured lines.
5. Pick up the phone receiver (or handset) and listen for a
dial tone; you’re now ready to make a VoIP call.
All manuals and user guides at all-guides.com