Audiovox VE926 - VE - 926 User manual

VE926
UNDER THE COUNTER 9” TV,
AM/FM RADIO, TELEPHONE &
DVD PLAYER
OWNER’S and INSTALL MANUAL
0
• Slot-in DVD Player & 9” TFT LCD Monitor
• Multi-function Remote Control
• Built-in Hands Free Speaker Phone
• Cable Ready 125 Channel TV Tuner
• AM/FM Radio
• 2 A/V Inputs
• Intercom Ready
• Internal Stereo Speakers
• Under Cabinet / Table Top Mounting

INTRODUCTION
WARNING – To prevent fire or shock hazard, do not expose this unit to moisture.
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NO
T
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
1
This symbol alerts the user to the fact that exposed “dangerous voltages”
reside within this product’s enclosure and contact with any of these voltages will
result in electric shock.
This symbol alerts the user that important and maintenance (servicing)
instructions in the literature accompanying the unit.
To prevent electric shock: do not use this unit’s polarized ac plug with extension
cords, receptacles or other outlets that prevent the units plug from being fully
seated and leave any part of the blade exposed.

INFORMATION
Installation of this equipment shall be in strict accordance with the manufacture’s instructions. Failure
to follow these instructions may cause or result in the reception of unwanted interference. This unit
complies with FCC Rules Part 15, which are designed to provide reasonable protection against
interference in a residential installation. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference with radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following means:
Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected
- Consult with the dealer or an experienced radio/TV technician for help
NOTE:
Record your unit’s Model Number and Serial Number in the space provided below. Refer to these
numbers if you need to call your AUDIOVOX dealer regarding this product.
MODEL No. SERIAL No.
_
____________________ _______________________
2

IMPORTANT SAFETY INFORMATION
1. Read Instructions –All the safety and operating instructions should be read before the product
is operated.
2. Retain Instructions –The safety and operating instructions should be retained for future
reference.
3. Heed Warnings –All warnings on the product and in the operating instructions should be
adhered to.
4. Follow Instructions –All operating and use instructions should be followed.
5. Cleaning –Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol
cleaners. Use a damp cloth for cleaning. Do not apply pressure to the LCD screen. Excess
pressure may damage the screen.
6. External Accessories –Do not use external accessories that have not been recommended by
the product manufacturer, as they may damage the unit.
7. Water and Moisture –Do not use this product near water, for example, near a bathtub, kitchen
sink, washing machine, in a wet basement, near a swimming pool, or similar environment.
8. Mounting considerations –Do not mount this product on an unstable surface. The product
may fall, causing serious injury to a child or adult, and may result in damage to the product. Use
only with a cart, stand, tripod, bracket, or table recommended by the manufactures, or sold with
the product. Mounting of this product should be in accordance the manufacture’s instructions,
and should use the mounting hardware provided with the unit by the manufacturer.
9. Carts –A product and cart combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may cause the product and cart
combination to overturn.
3
ded.
10. Ventilation –Slots and openings in the cabinet are provided for ventilation
and protect the product from over heating. These openings must not be blocked or covered.
This product should not be placed in a built-in installation such as a bookcase or rack unless
proper ventilation is provi
11. Power Sources –This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply in your home, consult your
product dealer or local power company.
12. Grounding or Polarization –This product may be equipped with a polarized alternating current
line plug (a plug having one blade wider than the other). This plug will fit into the power outlet
only one way this is a safety feature. If you are unable to insert the plug into the outlet, try rotating
the plug 180 degrees. If the plug still cannot be inserted, contact your electrician to replace your
outlet. Do not defeat the safety purpose of the polarized plug, doing so will void product warranty.

4
13. Power-Cord Protection –Route the power supply cord in a manner that protects it from being
stepped on or pinched by items placed on it. Pay particular attention to the power cord’s plug,
and the point where the power cord exits from the product.
14. Outdoor Antenna Grounding –If an outside antenna or cable system is being connected to the
product, verify that it is properly grounded to insure some type of protection against voltage
surges and static build-up. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides
information with regards to proper grounding of the mast, supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-
discharges unit, and connection to grounding electrode
15. Lightning –For added protection against lightning storms, or when the unit is not going to be
used for long periods of time, it is recommended that it be unplugged from the wall outlet and
disconnected from the antenna or cable system. This will prevent damage to the product due to
lightning and power-line surges.
16. Power Lines –An outside antenna system should not be located in the vicinity of overhead
power lines or other electric light or power circuit, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits, as contact with them might be fatal.
17. Overloading –Do not overload wall outlets, extension cords, or integral convenience receptacles,
as this can result in a risk of fire or electric shock.
18. Object and Liquid Entry –Never insert objects of any kind into this product through the
openings in the chassis as this may result in a fire or electric shock. Never spill liquid of any kind
on the product.
19. Servicing –Do not attempt to service this product yourself as opening or removing covers will
expose you to dangerous voltages and other hazards. Refer servicing to qualified service
personnel.
20. Damage Requiring Service –Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
A. When the power-supply cord or plug is damaged.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally as defined by the operating instructions.
Adjust only those controls that are covered by the operating instructions, as an
improper adjustment of other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to it’s normal operation.
E. If the product has been dropped or damaged in any way.
F. When the product exhibits a significant change in performance this indicates a need or
service.

21. Replacement Parts –When replacement parts are required, be sure the service technician has
used replacement parts specified by the manufacturer or that have the same characteristics as
the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
22. Safety check –Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper operating condition.
23. Mounting –The product should be mounted only as specified in this manual.
24. Heat –The product should be situated away from heat sources such as radiators, heating vents,
stoves, or other products (including amplifiers) that produce heat.
– Cable System Installation:
Note to CATV system installer: “This reminder is provided to call the CATV (CABLE-TV) system
installer’s attention to article 820-40 of the NEC, that provides guidelines for proper grounding and,
in particular, specifies that the cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as possible”
– Under cabinet mounting:
CAUTION: to reduce the risk of fire, do not place any heating or cooking product beneath this unit.
– Installation Marking:
“Use minimum No.26AWG wire for telephone interconnect cable.
– Speaker Impedance Marking:
External 8 ohms speaker only
5

TABLE OF CONTENTS
Before You Begin
Installation
Remote Control Functions
Modes of Operation
Using the DVD Loader
Technical Specifications
Troubleshooting Check List
Introduction 1
Important Safety Information 3
Table of Contents 6
Contents of package 7
Under Cabinet Installation 8
Countertop/Desktop Installation 9
Front Panel Controls 10
Rear Panel Controls 11
LCD Control Functions_________________ 12
Battery Installation 13
Remote Control Functions 14
Operation 17
Initial Set up 17
Channel Tuning Set up 17
Positioning the Screen 17
Setting the Time 17
Setting and Activating The Alarm 18
Deactivating Alarm 18
Setting the Alarm Tones 18
Setting the Alarm Volume 18
Setting the Cable TV Mode 19
Setting the Air TV Mode 19
Setting the Speaker Mode 19
Setting the Intercom Mode 19
Setting the Presets (In FM, AM or TV Modes) 19
Using the DVD Player 20
Inserting and Ejecting the Disc 20
Playback and Stop 20
Searching for a Specific Scene/Song
by Selecting the Chapter Number 20
by Using the Chapter 20
by Using Playback Speed 20
Repetitive Playback
To Repeat a Specific Section 21
Repeat a Specific Section (A-B Repeat)___ 21
Changing the Subtitle Language 21
Changing the Vocal Language 21
Zoom (To Enlarge a Picture) 21
Viewing Different Angles 22
Viewing the Main Disc Menu 22
Viewing the Playback Time, Title, Chapter Status 22
Playing Audio CDs 24
Playing MP3 Discs 24
Playing A JPEG FILE 26
SETUP (Language, Video, Rating) 26
Technical Specifications 30
Troubleshooting Check List 31
6

CONTENTS OF PACKAGE
7
1. VE926
re bag
g screws (4)
(4)
(4)
3. Re
er (4)
2. Hardwa
A. 2” Mountin
B. 2-1/2” Mounting screws
C. 3”Mounting screws (4)
D. Foot (4)
E. Hole cap
mote Control
4. Multi Height Spac
5. Battery (AAA)
nna
Adaptor
le Template
al
6. FM Dipole Ante
7. Right Angle Coaxial
8. FM Antenna Balun
9. AM Antenna
10. Mounting Ho
11. Owners Installation manu
12. Telephone Cord

UNDER CABINET INSTALLATION
1) Choose an appropriate mounting location underneath a cabinet or shelf. Close proximity to an electrical
outlet, TV antenna or cable connection and telephone jack will facilitate a neat, easy installation. Do not
mount the VE926 above a range or oven. Be sure that the location chosen will provide adequate access
to the electrical connections on the rear of the unit before continuing.
2) If the location chosen has a bottom edge molding it may be necessary to use the mounting spacers
provided to effectively lower the VE926 below or even with the molding. Measure the distance between
the edge molding and the bottom of the cabinet. The spacers and mounting holes are stepped to
achieve different mounting heights from .5” to 1”. Adjusting the mounting height is done by lifting and
rotating the spacer in the mounting hole. Choose a spacer height, which will allow the VE926 to clear
the edge molding.
3) Measure the thickness of the bottom of the cabinet or shelf and the spacer height chosen. Select the
shortest screw length, which will secure the VE926 to the bottom of the cabinet.
4) Cut out the template supplied and tape it in place onto the cabinet surface to be drilled. Center punch
the four holes indicated on the template and remove the template.
5) Carefully drill four 1/8″holes at the locations marked above.
6) Connect your TV antenna or cable system to the antenna connector on the rear of the VE926.
7) Attach the FM Dipole Antenna and position the antenna for the best reception.
8) Attach the AM Antenna and position the antenna for the best reception.
9) Position the VE926 and mount it in place using the selected screws. NOTE: Do not over-tighten.
10) Plug the AC power cable into the wall outlet. Route the wires safely away from heat and moisture
sources.
8

COUNTERTOP/DESKTOP INSTALLATION
NOTE: Use caution to avoid damaging the LCD screen and the main unit when converting this unit
from an under-counter unit to a countertop unit. Leave the protective plastic on the screen until this
procedure is completed.
1) Place the unit (with the screen facing up) on a soft padded surface.
2) Pivot the screen so that it is perpendicular to the front of the unit and then turn it sideways.
3) Remove the hinge guide covers (#1) using a flat blade screwdriver inserted into the removal
slots. Unscrew the mounting screws (#2). Remove the connector from the unit (#3), be
careful not to damage the screen (#5) or wires.
4) Turn the unit over and remove the blank cover (#4)
5) Connect the plug of the LCD monitor into the connector (#3). NOTE: Align the “L” and “R”
stamped on the screen-mounting bracket with the “L” and “R” molded into the connector
housing.
6) Replace the screws and slide the hinge guide covers onto the unit, be careful to not damage
the wires. NOTE: Do not over-tighten.
9
7) Insert the rubber pieces (#6) (Foot, Mounting Cap - please refer to the illustration above) into
the unit. Install the blank cover on the unused port.

FRONT PANEL CONTROLS
1) ON/OFF BUTTON –Power ON/OFF and Standby Condition(Time Display).
2) SET BUTTON –Press this button to set the TIME, ALARM, TV Mode or Speaker Mode.
3) TEL BUTTON –Selects the Hands-free speakerphone function.
4) SOURCE BUTTON –Selects the TV, FM, AM, AV1, AV2 and DVD functional modes.
5) T/F BUTTON –Selects Clock Mode When playing a DVD (MP3, CDDA).
6) CALL BUTTON –Press the CALL button to call another station.
7) TALK BUTTON –To answer from a station that was called, press the TALK button and keep it
pressed while talking.
* CALL and TALK buttons are working while Intercom function is selected.
8) INT BUTTON –Selects the Intercom function.
9) MUTE BUTTON –Press this button to mute the audio (++++ will appear and blink on the
display when the system is muted).
10
Stop an
Next butto
Play/Paus
Previous b
10) P4 BUTTON –Selected Preset Channel “4” in the Radio or TV mode.
d Eject (press and hold) button in DVD play mode.
11) P3 BUTTON –Selected Preset Channel “3” in the Radio or TV mode.
n in DVD play mode.
12) P2 BUTTON –Selected Preset Channel “2” in the Radio or TV mode.
e button in DVD play mode.
13) P1 BUTTON –Selected Preset Channel “1” in the Radio or TV mode.
utton in DVD play mode.

14) VOLUME UP (X) BUTTON –Press this button to raise the volume.
15) VOLUME DOWN (W) BUTTON –Press this button to lower the volume.
16) SEEK BUTTONS (TS-Right Side) –Press these buttons to go to next available channel with
sufficient signal strength.
17) CHANNEL BUTTONS (TS-Left Side) –Press these buttons to go to next available channel.
18) DISPLAY WINDOW –Displays the channel/station number, time, and selected source.
19) REMOTE INFRARED SENSORS –These sensors receive infrared command signals from the
hand held remote control unit.
20) MICROPHONE –Used for hands-free speakerphone operation.
21) SCREEN LOCK BUTTON –Used to lock screen in place.
22) Disc Insertion Slot
1) AC LINE CORD – Connects to AC outlet
2) AUDIO LINE OUT – Connect to low-level input of stereo system or low-level input of computer
speaker
REAR PANEL CONNECTIONS
7 8
3) SPEAKER OUT TERMINAL – Connect to external speakers (min. 8ohms)
4) FM ANTENNA – Allows the VE926 to be connected to a 75-Ohm external antenna for the
reception of FM broadcast signals.
5) AM ANTENNA - Allows the VE926 to be connected to an external antenna for the reception of
AM broadcast signals.
6) A/V (AUDIO/VIDEO) INPUT CONNECTORS – Connect to A/V OUTPUT of a VCR or
Camcorder.
7) TV ANTENNA (75 OHM ANTENNA CONNECTOR) -Allows the VE926 to be connected to a
75-ohm external coaxial antenna or cable TV system.
8) TEL JACK – Connect to telephone jack (not supplied) for hands-free speakerphone.
11

12
1. MENU Button – When pressed, the LCD control MENU is displayed.
m to be changed using
3. item in upward
4. rolls downward through menu items; also adjusts selected item; in
NO ttings to the factory settings, highlight RESET and press the
LCD Control Functions
2. SEL Button – Used to enter the picture menu. Highlight the menu ite
the UP/DOWN buttons and then press Select to adjust the highlighted item..
UP Button – Scrolls upward through menu items, also adjusts selected
(increase) direction.
DOWN Button – Sc
downward (decrease) direction.
TE: To reset all of the picture se
SEL button.

9)
BATTERY INSTALLATION
13
(Rear View, Battery Size AAA)

REMOTE CONTROL FUNCTIONS
(1) EJECT
(2) DVD
(3) TV
(4) SETUP
(5) SEEK DN, SEEKUP
(6) MENU
(7) FR(WW)
(8) STOP(■)
(9) PREV (IWW)
(10) Digit 0-9 Select
(11) TITLE
(12) DISPLAY
(13) SUB TITLE
(14) AUDIO
(15) SCREEN
(16) ANGLE (AP)
(17) ON/OFF
(18) A/V
(19) AM/FM
(20) TEL
(21) CH+, CH-
(22) ENTER
(23) MUTE
(24) FF (XX)
(25) SF (IX)
(26) NEXT (XXI)
(27) PLAY/PAUSE (XII)
(28) VOL +/-
(29) SEARCH
(30) REPEAT
(31) A-B Repeat
(32) ZOOM
(33) DELETE
(34) STEP (ADD)
14

15
cha
DVD REMOTE FUNCTION
(1) EJECT: Press this button to Eject and Load the disc tray.
(2) DVD: Press this button to select DVD mode of operation.
(4) SETUP: Displays setup menu for initial user settings.
(5) SEEK DN/UP (21) CH+/-: For selecting item on menu.
(6) MENU: For displaying the menu contained in the disc. (PBC ON/OFF Function - VCD)
(7) FR (WW): Fast reverse (2X, 4X, 8X, 20X and play).
(8) STOP (■): Press this button to stop disc playback
(1 time) Stop at the present playing point / (2 times) Stop playing
(9) PREV (IWW): For skipping to the next or previous chapter or track.
(10) Digit 0~9 Select: For direct selecting a chapter (or tack) and for password input.
(11) TITLE: For displaying the title menu contained in the disc.
(12) DISPLAY: For checking the current disc status.
(13) SUBTITLE: For selecting the subtitle language
(14) AUDIO: For selecting the audio language.
(15) SCREEN: Press this button to change Display Mode. Push the SCREEN Button to enlarge the
screen. The screen will be enlarged in the following order:
TV MODE: Normal (default) -> Full
AV, DVD MODE: Full (default) -> Normal
CDDA, MP3: Full (default) -> Normal -> LCD MONITOR OFF
(16) ANGLE: If a DVD disc contains sequences recorded from different camera angles you can
nge the camera angle for playback.
(17) ON/OFF: Press this button to turn power ON and OFF.
(22) ENTER: Press this button will cause the chapter (or track) change to occur immediately.
(23) MUTE: Press this button to remove all sound (++++ blanks on display window).
(24) FF (WW): Fast Forward ((2X, 4X, 8X, 20X and play)).
(25) SF (IX):Slow Play (1/2, 1/4, 1/6, 1/7) speed in forward.
(26) NEXT (XXI): For skipping to the next chapter or track.
(27) PLAY/PAUSE (XII): Start disc playback or Pauses disc play.
(28) VOL +/-: Use these buttons to increase or decrease the volume level.
(29) SEARCH: Allows a search to a desired Chapter/Title/Song/etc.
(30) REPEAT: For repeated playback of disc title, chapter/track.
(31) A-B: For specifying and repeating playback of a section of the disc.
(32) ZOOM: For magnifying the screen (1, 2, 3 or OFF).
(34) STEP: Play forward each time button is pressed.

16
ban
TV REMOTE FUNCTION
(3) TV: Press this button to select TV mode of operation.
(5) SEEK DN/UP: Use these buttons to advance to the next higher or lower station.
(10) 0~9: Use these buttons to make a direct channel selection
(15) SCREEN: Press this button to change Display Mode.
(16) AP (Auto Program): Press this button for 0.5sec to program and save all the stations on memory.
(21) CH+/-: Use these buttons to advance to the next higher or lower channel.
(23) MUTE: Press this button to remove all sound (++++ blinks on display window)
(28) VOL+/-: Use these buttons to increase or decrease the volume.
(33) Delete: Use to remove selected channel from memory.
(34) Step (Add): Use to add a selected channel to memory.
RADIO REMOTE FUNCTION
(5) SEEK DN/UP: Use these buttons to advance to the next higher or lower station.
(19) AM/FM: Each time this button is pressed, the VE926 will alternate between AM and FM radio
ds.
(21) CH +/-: Use these buttons to advance to the next higher or lower channel.
(23) MUTE: Press this button to mute the sound (++++ blinks on display window).
(28) VOL+/-: Use these buttons to increase or decrease the volume.
MISC REMOTE FUNCTION
(20) TEL: Press this button to answer an incoming call, press again to hang up the speakerphone.
(The VE926 contains a hands-free speakerphone).
(18) A/V: Press this button to select external A/V source 1 or 2.

OPERATION
INITIAL SETUP
This unit defaults to cable TV mode. When the unit is first powered on, it will detect the cable system
and auto-program the TV tuner to the available stations. Please wait while the unit auto-programs
before attempting to operate the unit. During this time the unit will not respond to any commands.
The unit will respond normally once the cable mode and channel search mode is concluded.
CHANNEL TUNING SETUP
If you are Cable TV subscriber, in addition to normal broadcast reception of VHF and UHF channels,
your new TV is capable of receiving many unscrambled Cable channels without the use of a converter
box. When set to broadcast (AIR) TV, it receives CH2-CH69. When set to one of the CATV modes
(STD, HRC, or IRC) it receives CH1-CH125. NOTE: Most cable companies broadcast in STD Mode
After a power interruption, the unit will go into a cable mode search (HRC, IRC, STD) and channel
search mode automatically. During this time the unit will not respond to any commands. The unit will
respond normally once the cable mode and channel search mode is concluded.
POSITIONING THE SCREEN
Press the screen lock button and pivot the screen forward until a comfortable viewing angle is reached.
The screen may also be rotated from side to side. Do not force the screen beyond its rotational limit.
The VE926 is now ready for use.
Pressing the ON/OFF button on the unit or the remote will turn the system on or off. Remember to turn
the unit off and pivot the screen to the closed position when not in use to prevent damage to the
screen.
SETTING THE TIME
NOTE: All settings (except setting the presets) are performed with the VE926 turned OFF.
1) Press the SET button and the minutes will flash.
2) Use the CH up/down button to set the minutes.
3) Press the SEEK button to toggle between the hour and minutes.
4) Use the CH up/down button to set the hour. (Check AM/PM indicator)
17
5) Press the ON/OFF button to return to the time display.

18
SETTING and ACTIVATING the ALARM
NOTE: The VE926 must be turned “OFF” when performing the following procedure.
1) Press the SET button twice to enter the alarm mode, press the P3 button to toggle between
the active and deactivated mode.
NOTE: If a series of dashes appear (--: --), the Alarm is DEACTIVATED.
2) Press the CH up/down buttons to set the desired hour/minute. When setting the alarm, check
the AM/PM indicator to assure the proper setting.
3) Press the SEEK buttons to toggle between the hours and minutes.
4) Press the ON/OFF button. The alarm is now set and activated. Once the alarm is set it will
sound each day at the same time as long as it is activated.
DEACTIVATING ALARM
1) Press the SET button twice to enter the alarm mode.
2) Press the P3 button once. The set time will disappear from the Display Window and a series of
dashes (--: --) will appear, Alarm DEACTIVATED mode.
3) Press the ON/OFF button. The alarm is now deactivated.
NOTE: The set time will be stored in memory and can be reactivated whenever desired by
performing step 1) – 3) of the ACTIVATING ALARM procedure.
SETTING THE ALARM TONES
1) Press the SET button twice (power off).
2) Press the P4 button once to hear the alarm tone.
NOTE: Alarm must be in the “Activated” mode to hear tones.
3) Each time CH UP/DOWN button(s) is pressed it will select a different alarm tone.
4) Press the ON/OFF button to confirm the selected tone.
5) When the alarm sounds, press the ON/OFF button to turn it off.
SETTING THE ALARM VOLUME
1) Power OFF
2) Press the SET button twice for the Alarm setting mode.
3) To select alarm tone, Press "P4" button and press volume UP/DOWN for your desired volume
level. Then, press "SET" button for volume setting

19
* I
SETTING THE CABLE TV MODE
1) Press the SET button three times to enter the TV/Cable configuration mode.
2) CABLE or AIR will appear on the display.
3) Press the SEEK button to select Cable mode.
4) Press the CH UP/DOWN button(s) to select the desired cable mode (STD/IRC/HRC).
5) When the desired mode is reached, press the ON/OFF button to confirm.
SETTING THE AIR TV MODE
1) Press the SET button three times to enter the TV/Cable configuration mode.
2) Press the SEEK button to select the AIR mode.
3) Press the ON/OFF button to confirm.
SETTING THE SPEAKER MODE
1) With power off, press the SET button four times to enter the speaker configuration mode.
″ISP (or ESP) ″appears on the VFD.
2) Press the seek button to toggle between the ″I SP″and ″E SP″
3) When the desired mode is reached, press the ON/OFF button.
SETTING THE INTERCOM MODE
4) With power off, press the SET button five times to enter the intercom configuration mode.
″Int On (or Int OFF) ″appears on the VFD.
5) Press the seek button to toggle between the ″Int On″and ″Int OFF″
6) When the desired mode is reached, press the ON/OFF button.
nt OFF : default, No response to call signal.
SETTING THE PRESETS (IN AM, FM OR TV MODES)
1) Tune to the desired channel/station.
2) Press the SET button and the display flashes.
3) Press desired preset (P1, P2, P3 & P4) to confirm the selection.
NOTE: you can preset 4- AM, 4- FM and 4- TV Programs