Audiovox LCM5869NP Installation instructions

128-6324
1 of 22
LCM5869NP & LCM7069NP
Remote Controlled Color Display Monitor
Installation and Owner's Manual
Released:03-27-02.
ELECTRONICS COR
P.
®
5.8-Inch Color Display Monitor
7-Inch Color Display Monitor

128-6324
2 of 22
1
EXPLANATION OF GRAPHIC SYMBOLS
WARNING:
TOPREVENTFIRE ORELECTRIC SHOCKHAZARD,DO NOTEXPOSE
THISPRODUCT TO RAINOR MOISTURE.
CAUTION:
1. This product is designed to operate with a 12 volt, negative ground bat-
tery system.
2. Disconnect the ground wire from the battery terminal before connecting
the electrical system. Refer to the electrical connection diagram to avoid
wrong connection of the electrical system.
Always use authorized service center for service assistance.
3. Do not operate the monitor at temperatures below 32°F (0°C) or above
104°F (40°C).
4. Keep the monitor clean and dry.
5. Never attempt your own repairs. This unit should be installed and re-
paired by qualified technicians or service personnel..
6. Do not drop the monitor or expose to strong impacts.
7. Do not expose to direct sunlight for extended periods of time.
8. Use proper insulation material to prevent short-circuiting of the supply
system.
9. Tighten all loose wires after installation.
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK DO
NOT REMOVE COVER (OR BACK) NO SERVICEABLE PARTS
INSIDE REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with the arrowhead within a triangle is in-
tended to alert tell the user that parts inside the product are
capable of producing an electric shock .
The exclamation point within a triangle is intended to alert the
user that important operating and servicing instructions are
being provided.

128-6324
3 of 22
MATERIALS LIST
1. System Monitor (LCM5869NP=136C2185) or
(LCM7069NP=136C2184) (1pc.)
2. Remote Control Unit (136B2156, used with LCM5869NP
and LCM7069NP) with Lithium Battery, 3V,CR 2025 (1pc.)
3. Interconnect Box (136B2183, used with LCM5869NP and
LCM7069NP) (1pc.)
4. Monitor Cable, 8' (112B3151, used with LCM5869NP and
LCM7069NP) (1pc.)
5. Headrest Mounting Tray (LCM5869NP=102C3739)
or (LCM7069NP=102B3738) (1pc.)
6. Trim Ring for Mounting Tray (LCM5869NP=102C3746)
or (LCM7069NP=102B3745) (1pc.)
7. Power Cable, 2.46' (112B3127, used with LCM5869NP
and LCM7069NP) (1pc.)
8. Removal Tool (108B3632) (1pc.)
2
 !
"
#$
%&

128-6324
4 of 22
3
SYSTEM OVERVIEW
The LCM5869NP is comprised of a 5.8" Thin Film Transistor (TFT) Liq-
uid Crystal Display ( LCD) Monitor. The LCM7069NP is comprised of a 7"
Thin Film Transistor (TFT) Liquid Crystal Display ( LCD) Monitor. The
Monitor for both of these systems have a 16:9 Aspect Ratio display that
allows the user to select between two video sources (Not Supplied). The
Monitors display all functions with the comprehensive On Screen Display
(OSD). Can be used with optional one or two channel Wireless Infrared
Headphones.
OPTIONAL AUDIO CONNECTION
Materials Needed for Optional Audio Connection:
Option #1
1) IRT456 (CHA) Infrared Transmitter, Single Channel............. (1pc)
2) MVIRHS Single Channel (A) Infrared Headphone(s) ............. (1pc)
Option #2
1) IRT457 (CHB) Infrared Transmitter, Dual Channel ............... (1pc)
2) IR2CHS Dual Channel (A/B) Infrared Headphone(s) ............ (1pc)
Before installing the IRT boards gently bend the three IR LEDs closest to
the center of the vehicle toward the center of the vehicle.
NOTE: When installing two screens, install one IRT456 Single Channel
Infrared Transmitter into the left Headrest Mounting Tray and one IR2CHS
Dual Channel Infrared Transmitter into the left Headrest Mounting Tray.
IRT456CHABEFORE
IRT457CH BBEFORE IRT457CHBAFTER
IRT456CHAAFTER

128-6324
5 of 22
4
Insert the IRT boards into their respective compartments in the Headrest
Mounting Tray and insert the plug into the IRT board. When the user
switches the video source utilizing the ON/OFF/MODE switch, the A/B
switch (see illustration below) on the IR2CHS Headphones must also
be switched to select the desired audio source.
IMPORTANTNOTICE
It is unlawful in most jurisdictions to drive a motor vehicle which is
equipped with a television viewer or screen that is located at the point
forward of the back of the driver’s seat, or that is visible directly or indi-
rectly, to the driver while operating the vehicle.
1) Wireless Headphones (1 Channel) .......................P/N=MVIRHS
1) WirelessHeadphones(2Channel) .................. P/N=IR2CHS
POWER
VOL
POWER
OFFON
INFRAREDHEADPHONES
AUDI
O OX
AUDI
O OX
INFRAREDHEADPHONES
CH.A
CH.B
POWE
R
OFF-ON
NOTE: The following IRT board installation procedure should be per-
formed between steps 10 and 11of the Headrest Mounting procedure on
page 10.
Optional Wireless Headphones:
POWER
VOL
POWER
OFFON
INFRAREDHEADPHONES
AUDIO OX
AUDIO OX
INFRAREDHEADPHONES

128-6324
6 of 22
VEHICLE PREPARATION
1) Decide on the system configuration and the options that will be in-
stalled (i.e.what components,VCP,DVD, TV Tuner,VideoGame,
Monitor,FMModulator,etc.).
2) Read the manuals and get familiar with the electrical requirements
andconnections.
3) Decideonthemountinglocationsandmethodsofmountingtheprod-
ucts.
4) Preparethe vehicleby removingany interiortrim necessaryto gain
accesstothevehicle'swiringaswellasallareaswhereinterconnect-
ingwireharnesseswillbelocated.Ifanyaccessholesneedtobecut
intothevehicle,headrests,orothertrimcomponents,thisshouldbe
performednow.(RefertotheInstallationProcedure).
5) Runthewiringharnessesandcablingthroughoutthevehicleasnec-
essary.(Refertothewiringinstructionsfortheindividualcomponents
andaccessoryoptionsbeinginstalled).Besure,thatallthewiringis
protectedfromsharpedgesandisroutedinsuchamannerthatitwill
not be pinched, when it is fully installed. Be sure to leave enough
slack in the wiring at each component to allow sufficient working
room.
6) Remove all the A/V system components from their packaging and
thenplacetheminthevehicleattheirrespectivelocations.
7) Locateanaccessorypowersource(RedWire)(+12VDCpresentwhen
theignitionkey is in the accessoryand run positions. 0VDC should
bepresent, whentheignition keyis intheOFFposition).Generally,
thesewirescanbefound attheignitionswitchor fusebox.
8) LocateaConstantPowerSource(YellowWire)(+12VDCpresentat
all times).
NOTE: Ensure that the accessory power is fused at the source.
Failure to do so may result in vehicle wiring damage.) Ground the
blackwire to a chassis groundclose to the mountinglocation of AV
sources.
9) Connectallthecomponentstogether(electrically)andverifythatthe
proper operation of all the system functions. NOTE: This is best
doneBEFOREthecomponentsarepermanentlymounted.
5

128-6324
7 of 22
6
10) After verifying the proper operation of the system, proceed to mount
each component.
11) The mounting method, and the location will vary from vehicle to
vehicle; this manual will focus on typical Headrest installation pro-
cedures.
12) The best location for the system components is:
a) Monitor: Headrest or bracket (optional) mounted onto a
flat surface.
b) System Interconnection Box (AVX-6869): In line with all the
system cabling and in an area where it can be easily accessed.
c) System Main Cable: Under either seat where monitors
are located.
Tools and Materials Required:
Utility knife or box cutter with sharp blade.
Permanent Marker.
Tie Wraps.
INSTALLATION
Mounting with Optional Bracket:
This procedure describes mounting the system monitor using an op-
tional Surface Mount Bracket (sold separately, P/N FB1)
1) Start by firmly attaching the Surface Mount Bracket onto a clean flat
surface.

128-6324
8 of 22
7
3) Adjust viewing angle of monitor by tightening the fastener at the
side.
4) When the system components are mounted, test the system to
verify that it is functioning correctly. Make sure that no wiring was
pinched, or connected improperly during the final installation.
Surface Mount
MountingBracket
FastenerWheel
Monitor
2) Slide monitor onto Surface Mount Bracket and then tighten the
fasten wheel.
SurfaceMountFastener

128-6324
9 of 22
8
1) Remove the headrest from the
vehicle for easiest installation.
2) Lay headrest on a flat surface.
3) Center trim collar on headrest
as shown.
NOTE: Depending on the angle of
the headrest the Trim Ring and
housing may be mounted upside
down.
4) Using a permanent marker,
mark headrest material along
the interior of the Trim Ring.
5) Remove the Trim Ring and
mark an “X” from corner to cor-
ner as shown.
Headrest Mounting:
Monitor Mounting
Tray Trim Ring Headrest

128-6324
10 of 22
9) Using your fingers, tear the foam
out of the headrest leaving a re-
cess where the shell will be in-
serted.
NOTE: At this point you will need to
install the harness up through the area
into the recess. It may be helpful to
follow one of the posts and tie wrap it
to the post for restraint.
6) Usingtheutility knife, cut the head-
rest material along the “X” lines.
Do not cut the material along the
other lines at this time.
7) This will leave you with an “X” cut
as shown.
8) Pull the flaps up and cut the foam
beneath the material to the proper
depth. Cut all four sides of the
foam.
9