Audiovox Eddie Bauer PE703 User manual

PE703
PORTABLE 7" LCD MONITOR AND DVD PLAYER
128-7203

2
NOTICE:
This Product incorporates copyright protection technology that is pro-
tected by method claims of certain patents and other intellectual prop-
erty rights owned by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be authorized by
MacrovisionCorporation,andisintendedforhomeandotherlimitedview-
ing uses only unless authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
NOTICE:
An LCD panel and/or video monitor may be installed in a motor vehicle
and visible to the driver if the LCD panel or video monitor is used for
vehicle information, system control, rear or side observation or naviga-
tion. If the LCD panel or video monitor is used for television reception,
video or DVD play, the LCD panel or video monitor must be installed so
thatthese featureswill onlyfunction whenthe vehicleis in‘park’ orwhen
the vehicle’s parking brake is applied.
An LCD panel or video monitor used for television reception, video or
DVD play that operates when the vehicle is in gear or when the parking
brake is not applied must be installed to the rear of the driver’s seat
where it will not be visible, directly or indirectly, to the operator of the
motor vehicle.

3
A. Introduction
Thank you for choosing the PE703 portable DVD player. The main
features include a 7" Wide Screen (16:9Aspect Ratio) Liquid Crystal
Display (LCD)monitor and aDVD player. The unit applies the latest
state of the art electronics and is designed for use in hotels, offices
or your home. The unit is constructed to provide years of reliable,
trouble-free service, and is compact so that you can take it with you
anywhereandis designedforquick andeasyinstallation. Please read
the entire instruction manual supplied with this product prior to using.
The documentation will assist you in installing the system properly to
obtain the best equipment performance. Please save this manual for
later use.
B. Cautions and Warnings
1. Placement
To prevent fire or electric shock, do not expose this appliance to
rain or moisture. Do not place the set on an unstable cart, stand,
tripod,bracket ortable to prevent it from falling. Keepthe unitaway
fromstrong magnets,heatsources, directsunlight, excessivedust.
If the unit is brought directly from a cold to a warm location, mois-
ture may condense inside the unit. When you move it from a cold
to a warm location, wait for about one hour before operating the
unit, or remove the disc and leave the unit turned on until the mois-
ture evaporates.
2. Installation
Ensure that the PE703 is installed in accordance with the instruc-
tions and illustrations provided in this manual.
3. Caution
Do not push objects of any kind into the unit through openings; do
not spill or spray liquid of any kind on or in the system (this may
result in a fire or electric shock). Do not place anything heavy on

4
the unit. To ensure proper ventilation and proper operation, never
cover or block and openings with a cloth or other material. Keep
the unit away from an open flame such as,.fire, candle etc,. It is
hazardous to replace the battery incorrectly. Replace the battery
only with the same or equivalent type, in order to protect the
enviromnent,please dispose the battery properly. Do not use the
unit in temperatures higher than 104 degrees Fahrenheit or 40 de-
grees Celcius.
4.Disassemble
Do not attempt to disassemble the cabinet. There is a risk of elec-
tric shock and/or exposure to Laser Radiation. Contact qualified
service personnel if your system needs repair.
5. Cleaning Unit
Whencleaning,makesurethe system isunplugged fromthepower
source. Do not use liquid cleaners or aerosol cleaners. Use a cloth
lightly dampened with water for cleaning the exterior of the system
only.
6. Disc
Do not use irregularly shaped discs such as heart or star-shaped
discs as they may cause the unit to malfunction. Do not stick pa-
per, tape or glue on the disc. Do not expose the disc to direct sun-
light or heat sources. Do not touch the surface of disc. Handle the
disc by its edge. Clean the disc by wiping the disc from the center
out with a cleaning cloth. Remove the disc from the unit and store
it in its case after playing. Some playback operations of discs may
be intentionally fixed by software producers. Since this unit plays
discs according to the disc contents the software producers de-
signed, some playback features may not be available.Also refer to
the instructions supplied with the discs.

5
C. Contents
1. 1 x 7’’ LCD Monitor & DVD Player Combo
2. 1 xAC to DCAdapter
3. 1 x Remote Control with battery (CR2025)
4. 1 x Instruction Manual
5.1 xAudio/VideoCable
6. 1 x DC PowerAdapter
7. 1 x Rechargeable Battery
D. Powering and installation
1. Powering the system indoors (Refer to Figure 1)
Plug one end of the AC to DC adapter into the DC 9V jack on the
rightsideof themainunit, thenplugthe otherendinto the 120V AC
power outlet.
2. Powering the system in a car (refer to Figure 1)
Plug one end of the DC power adapter into the DC 9V jack on the
unit, then plug the other end into the vehicle power socket.
Figure 1

6
E. Controls, Indicators, and Connectors
1. Unit View (Refer to Figure 2)
Figure 2
1)MENU Button
2) Up Button
3) Left Button
4) Down Button
5) OK Button
6) Right Button
7) Open Button
8) Skip- Button
9) Stop Button
10) Skip+ Button
11) Play Button
12) Pause Button
13) Screen Mode Button
14) LCD Panel Shut Off Switch
15) Remote Control Sensor
16) Power Indicator
17) Video output Jack
18) DVDAudio output Jack
19)Video Input Jack
20)AudioInputJack
21) Power On/Off Switch
22) Volume Control
23) Headphone Jack 2
24) Headphone Jack 1
25) DC 9V Input Jack
26) Brightness Control
1
2
3
4
65 78910
11
12
13
14 15
16
17181920
21 22 2324 25
26

7
2. Remote Control View (Refer to Figure 3)
1) Display Button
2) Angle Button
3) Subtitle Button
4) Audio Button
5) Zoom Button
6) UP/DOWN/LEFT/RIGHT/
ENTER Buttons
7) Return Button
8) A-B Button
9) Forward Button
10) Reverse Button
11) Slow Button
12) Stop Button
13) Numeric Keypad
14) Setup Button
15) Menu Button
16) Repeat Button
17) Skip- Button
18) Skip+ Button
19) Play Button Figure 3
20) Pause Button
F. Loading and Playing a Disc
a. After connecting power to the unit, turn on the DVD player by slid-
ing the power switch to the on position. The power indicator will
light.
b. Open the disc tray by pressing OPEN, and place a disc into the
tray with the label side facing up.
c. Close the tray by pressing the “PRESS” area on the door. The unit
will load the disc and start playing.
d. Rotate BRIGHTNESS and VOLUME to adjust the LCD’s bright-
ness and the DVD player’s volume.
e. To stop playing a disc, press STOP.

8
G. SETUP
Press ‘SETUP’ to display the Main screen of the SETUP Menu on the
screen. Press ‘SETUP’ again to exit the SETUP Menu and the unit
will resume it’s last playback mode.
Main Setup Menu Screen Display
1) Press ‘SETUP’, the ‘General Setup Page’ will display on screen.
a).Select ‘TV Display’ using the UP/DOWN button, and then press
RIGHTto enterthe submenu. Selectthe TVdisplay modeon the
screen using UP/DOWN, and press ENTER to confirm the set-
ting. Press LEFT to return.
* Normal/PS: When the player is connected to a normal TV, and
a wide picture is shown on the full screen.
* Normal/LB: When the player is connected to a normal TV, and
a wide picture is shown on the screen with a black strip at both
the top and bottom of the screen.
* Wide: When the player is connected to a wide screen TV, a
wide picture is shown on the full screen.
TV Display Screen Display

9
b).Select ‘Angle Mark’ using the UP/DOWN buttton, and then press the
RIGHT button to enter the submenu. Choose Angle Mark on or off
using the UP/DOWN button and then press ENTER to confirm the
setting. Press the LEFT button to return.
Angle Mark Screen Display
* On: The screen will show the angle mark icon. (*If an angle
optionis available).
Off: The screen will not display theAngle Mark
NOTE: Not all discs contain the features above. The above
features are disc dependent.
c). Select ‘Screen Saver’ using the UP/DOWN button.
Screen Saver Screen Display
*On: Enable screen saver
*Off: Disable screen saver (off)
*NOTE: The DVD player will enter the Screen Saver mode after ap-
proximately five minutes if the same image remains on the screen.

10
d). Select ‘Last Memory’ by UP/DOWN button.
Last Memory Screen Display
*On: The unit will return to the last position on the disc.
*Off: The unit will not return to the last position on the disc.
2) Select “Video Quality Setup”by using the LEFT/RIGHT button, press
ENTER to enter the video quality setup page.
Video Quality Setup Menu Screen Display
a).Select ‘Brightness’ by using the UP/DOWN button, then press EN-
TER you can change the Brightness by pressing the LEFT/RIGHT
button. To exit Brightness Setting, press ENTER again to return
themain Menu.
Brightness Screen Display
State

11
b).Select ‘Contrast’ by using the UP/DOWN button, then press ENTER
you can adjust the Contrast by pressing the LEFT/RIGHT button.
Contrast Screen Display
To exit ‘Contrast’ Setting, press ENTER again to return the main Menu.
c).Select ‘Hue’ by using the UP/DOWN button, then press ENTER you
can adjust the Hue by pressing the LEFT/RIGHT button.
Hue (Tint) Screen Display
To exit ‘Hue’ Setting, press ENTER again to return the main Menu.
d).Select ‘Saturation’ by using the UP/DOWN button, then press ENTER
you can adjust the Saturation by pressing the LEFT/RIGHT button.
Saturation (Color) Screen Display
To exit ‘Saturation’ setting, press ENTER again to return to the
main Menu.

12
3).Select “Password” using the LEFT/RIGHT button, then press the
ENTER button to enter “Password Setup Page”.
Password Change Menu Screen Display
Press ENTER to enter the Password Change Page. Input the Old
Password or the Default Password, the New Password, and the Con-
firmed New Password. Press ENTER to confirm the change.
Password Change Menu Screen Display
NOTE: The Default Password is 3308. This password is always
effective even after you have selected your own password and
changed it. To avoid the possibility of others using the default
password to set the parental level and change the password, you
can record this default password in another area and delete it from
this manual. Some discs can be limited depending on the age of
users while some discs can not.

13
4).Withnodiscinsidetheplayerselect “Preference”usingthe LEFTorRIGHT
button, then press ENTER to enter the preference page.
a. Select ‘Audio’ using the UP/DOWN button, then press RIGHT to
enterthe submenu.Select the audiolanguage youdesire usingthe
UP/DOWN button, then press ENTER to confirm the setting. Press
LEFT to return.
Preference Audio Language Screen Display
b.Select ‘Subtitle’ the using theUP/DOWN button, then press RIGHT
toenter thesubmenu. Selectthe desired subtitlelanguage orSub-
title Off using the UP/DOWN button, then press ENTER to confirm
the setting. Press LEFT to return.
Preference Subtitle Language Screen Display

14
c. Select ‘Disc Menu’ using the UP/DOWN button, then press RIGHT to
enter the submenu. Select the Disc Menu Language you desire using
theUP/DOWNbutton, then pressENTERtoconfirm thesetting.Press
LEFT to return.
Preference Disc Menu Language Screen Display
Note: Language and subtitle selection is only available for discs that
are recorded in the above listed languages. If the selected language
isnot available, theplayer will playand displayonthe screenthe origi-
nal recorded language contained in the disc.
d. Select ‘Parental’ using the UP/DOWN button, then press RIGHT to
enter the submenu.
Parental Preference Screen Display
Select the parental level you desired using the UP/DOWN button for
discs with lock-out function or multiple rating levels. These are listed
fromthe lowestlevel (1 Kid Safe) tothe highestlevel (Adult).Enter a4
digit password, then press ENTER to confirm the parental level set-
ting.
NOTE: The level of 8Adult is the factory default.

15
e. Select ‘Default’ using the UP/DOWN button, then press RIGHT to en-
ter the submenu. Press ENTER to make the setting return to the fac-
tory-set mode.
NOTE: The parental setting is not affected by the default reset
function.
Loading Factory Setting Screen Display

16
1. Basic Operation
Turntheuniton/off
Remove/loadthedisc
StartPlay/Executeitemorsetting
Playat1/2,1/4,1/8or1/16timesspeed
StillPicture
(1time)Stopatthepresentplayingpoint/
(2times)Stopplaying
Goto the nextchapter,trackorscene dur-
ingplayback
Gobacktothepreviouschapter,trackor
sceneduringplayback
Scanforwardat2,4,8,16or32timesspeed
Scan backward at 2, 4, 8, 16 or 32 times
speed
UsedforMenuNavigation
Executeitemorconfirmsetting
Selectitemorsetting
Return
Displaythe mainmenu ofthedisc
Repeatplayingtitle,chapter,ortrack
RepeataspecificportionfrompointAtopoint
B of the disc
Display information (title, chapter, track,
time,etc.).
Changetheviewinganglesonthescene
Selectthe subtitle languageandturn it on/
off
Selecttheaudiolanguage
Enlargean imageto2, 3,or4 timesthe
originalsize.
Display the setup menu to select and set
items,andexitthesetupmenu.
POWER
OPEN
PLAY
SLOW
PAUSE
STOP
SKIP+(NEXT)
SKIP-(PREVIOUS)
FORWARD
REVERSE
LEFT/RIGHT/UP/DOWN
ENTER
NUMBERS
RETURN
MENU
REPEAT
A-B
DISPLAY
ANGLE
SUBTITLE
AUDIO
ZOOM
SETUP

17
2. MENU
ADVD is dividedintosections called titlesandchapters.When you
playaDVD,arootmenu ofthediscwillappearonthescreenofyour
TVorMonitor.Thecontentsofthemenuvaryfromdisctodisc.Press
MENUduringplaybacktodisplaythemenu.SomeDVDsonlyallow
youtoselectdiscplaybackoptionsusingtheDVDrootmenu.
3. DISPLAY
1. PLAYING TIME AND REMAINING TIME
a.During playbackpressthe ‘DISPLAY’ buttonto displaythecur-
rentTitle Number (1), the totalNumber ofTitles (2), the current
ChapterNumber(3), the total Number of Chapters (4),andthe
Playing elapsedTimeforthetitle(5).Theheadingwilldisappear
automaticallyafter3secondsifthe‘Display’buttonisnotpressed.
Title, Chapter Number, and Time Screen Display
b.Press‘DISPLAY’againtodisplaytheRemainingTimeof thetitle.
Theheadingwill disappearautomatically in3seconds.
Title Remaining Time Screen Display

18
c. Press ‘DISPLAY’ a 3rd time to display the Elapsed Time for the
chapter. The heading will disappear automatically in 3 seconds.
Chapter Elapsed Time Screen Display
d. Press ‘DISPLAY’ a 4th time to display the Remaining Time for the
chapter. The heading will disappear automatically in 3 seconds.
Chapter Remaining Time Screen Display
e.Press‘DISPLAY’a 5thtimeto exit,‘DISPLAYOFF’willbedisplayed
and will disappear automatically in 3 seconds.
2.ANGLE
Duringplaybackofadisc,press‘ANGLE’todisplaytheavailableangles
for discs containing multi-angles*, with the current angle number (1)
and the total number of angles (2) displaying. Press ‘ANGLE’ to se-
lect another angle, then press again to exit and return to the normal
viewing angle. The angle mark will disappear automatically if the
‘ANGLE’ button is not pressed again in 3 seconds.
*NOTE: Not all discs contain this feature.

19
Angle Screen Display
3. SUBTITLE
Duringdiscplayback press‘SUBTITLE’to selectthesubtitle language
you desire*, with the current Subtitle Language Number (1) and the
total Number of Subtitle Languages (2) displayed. If there are mul-
tiplelanguages press‘SUBTITLE’ againto select another subtitle lan-
guage.Toturnsubtitles OFF,press the ‘SUBTITLE’button until ‘SUB-
TITLEOFF’ isdisplayed. The Subtitledisplay willdisappear automati-
cally if the ‘SUBTITLE’ button is not pressed again within 3 seconds.
Subtitle Screen Display
*SomeDVDsonlyallowaccesstothisfunctionthroughtheDVDmenu.

20
4. AUDIO
During playback press ‘AUDIO’ to select the audio language you de-
sire*, with the current Audio Channel Number (1) and the total num-
ber of Audio Channels (2) displayed. Press AUDIO again to select
another audio language. The audio display will disappear automati-
cally if the ‘AUDIO’ button is not pressed within 3 seconds.
Audio Language Screen Display
* Some DVDs only allow access to this function through the DVD
menu.
5. ZOOM
During playback press ‘ZOOM’ to enlarge the picture by 2x, 3x or 4X
with the current zoom multiple.(1)Press “ZOOM”one time ,the picture
will be enlarged 2X.(2)Press “ZOOM” a 2nd time, the picture will be
enlarged 3X.(3)Press “ZOOM” a 3rd time, the picture will be enlarged
4X.(4)Press “ZOOM”4th time, the picture will return to normal size.
Zoom Screen Display