AUTEC A08 User manual

Instruction Manual for the use and the
maintenance of the Radio Remote Control
Original instructions
Part C: A8+ (Model A08 Type LA5AM)
Transmitting Unit
AIR SERIES
LIUA8BEN0_eng-01

WARNING
THIS PART OF THE MANUAL CONSISTS OF: Part C - Information, instructions and
warnings for the A8+ (Model A08 Type LA5AM) Transmitting Unit. The Manual consists
of Part A – General, Part B – Conformity and Frequencies, Part C – Transmitting Unit, Part
D – Receiving Unit, Part E – Battery and Battery Charger, plus the Technical Data Sheet.
THIS MANUAL, INCLUDING ALL PARTS THEREOF, AND ALL INSTRUCTIONS CONTAINED
HEREIN, MUST BE READ CAREFULLY AND UNDERSTOOD BEFORE INSTALLING,
USING, MAINTAINING OR REPAIRING THE AUTEC RADIO REMOTE CONTROL.
FAILURE TO READ AND COMPLY WITH ALL APPLICABLE WARNINGS AND
INSTRUCTIONS OR ANY ONE OF THE LIMITATIONS NOTED IN THIS MANUAL CAN
RESULT IN SERIOUS BODILY INJURY OR DEATH, AND/OR PROPERTY DAMAGE.
THE AUTEC RADIO REMOTE CONTROL IS NOT A STANDALONE PRODUCT AND IS
INTENDED ONLY AS A COMPONENT ON A MACHINE:
-ON WHICH AND WHERE THE USE OF A RADIO REMOTE CONTROL IS APPROPRIATE,
-THAT CAN BE OPERATED SAFELY AND IN ACCORDANCE WITH ALL APPLICABLE
LAWS, REGULATIONS AND STANDARDS BY SUCH REMOTE CONTROL.
ACCORDINGLY, IT IS THE RESPONSIBILITY OF THE MANUFACTURER AND OF THE
DESIGN PROFESSIONALS OF THE MACHINE ON WHICH THE AUTEC RADIO REMOTE
CONTROL IS TO BE INSTALLED, that a full and proper risk assessment is done to
determine whether the use and installation of the Autec Radio Remote Control is
appropriate for the safe and e󰓐ective operation of the Machine by a Radio Remote Control
in the facility and for the purposes intended, and that the installation, maintenance
and operation of the Autec Radio Remote Control and all of its components are done
solely and completely in accordance with this Manual, and with all local applicable
laws, safety rules and standards (all of the foregoing referred to herein as “Laws,
Regulations and Standards”).
With reference to the USA market the Laws, Regulations and Standards include all safety
rules and regulations of the Occupational Safety & Health Administration (OSHA) (http://
www.osha.gov), all federal, state and local laws, regulations and building and electrical
codes, and all applicable standards, including but not limited to ANSI Standards.
AUTEC LIUA8BEN0_eng-01

It is also the responsibility of the Manufacturer and of the design professionals of
the Machine on which the Autec Radio Remote Control is to be installed and used to
be certain that the structure, condition, organization and markings of the Machine as
installed at the facility is appropriate for and will allow for the safe and reliable use and
control of the Machine through the Autec Radio Remote Control interface.
IT IS THE RESPONSIBILITY OF THE OWNER AND FACILITY OPERATOR, AND THEIR
DESIGN PROFESSIONALS, that the installation, maintenance and operation of the Autec
Radio Remote Control and all of its components are done solely and completely in
accordance with this Manual, and with all applicable Laws, Regulations and Standards,
even local. It is also the responsibility of the Manufacturer of the Machine on which the
Autec Radio Remote Control is to be installed and used, and their design professionals,
to be certain that the structure, condition, organization and markings of the Machine
as installed at the facility is appropriate for and will allow for the safe and reliable use
and control of the Machine through the Autec Radio Remote Control interface.
ONLY QUALIFIED AND PROPERLY TRAINED PERSONNEL SHOULD BE PERMITTED
TO OPERATE OR USE THE AUTEC RADIO REMOTE CONTROL AND THE MACHINE
OPERATED BY OR THROUGH THE AUTEC RADIO REMOTE CONTROL. ONLY QUALIFIED
AND PROPERLY TRAINED PERSONNEL SHOULD BE PERMITTED TO BE IN THE VICINITY
OF MACHINE OPERATED BY OR THROUGH THE AUTEC RADIO REMOTE CONTROL.
FAILURE TO PROPERLY INSTALL, OPERATE, MAINTAIN AND SERVICE THE AUTEC
RADIO REMOTE CONTROL CAN RESULT IN SERIOUS BODILY INJURY OR DEATH
AND/OR PROPERTY DAMAGE. Refer to this Manual and each of its Parts for further
assistance or contact Autec. Autec is not responsible for and shall not be held liable
for any installation of the Autec Radio Remote Control not performed by Autec or for
any use of the Autec Radio Remote Control not in complete compliance with, and/or
not maintained in complete compliance with, all Autec instructions and warnings and
all applicable Laws, Regulations and Standards, even local.
Autec is not responsible for and shall not be held liable for any alteration or modi󰄈cation
of the Autec Radio Remote Control, or the use of non-Autec components or products
used with or incorporated into the Autec Radio Remote Control.
IT IS THE RESPONSIBILITY OF THE OWNER AND FACILITY OPERATOR, AND THEIR
DESIGN PROFESSIONALS, to be certain that the Autec Radio Remote Control is
properly maintained and serviced at all times in compliance with all Autec instructions
and warnings, and with all applicable Laws, Regulations and Standards, even local.
LIUA8BEN0_eng-01 AUTEC

IT IS THE RESPONSIBILITY OF THE OWNER AND FACILITY OPERATOR, AND THEIR
OFFICERS, MANAGERS AND SUPERVISORS, to be certain that all Users of the Autec
Radio Remote Control and that all Persons who are or will be working with or near
the Machine operated by or through the Autec Radio Remote Control are fully and
properly educated and trained by quali󰄈ed Personnel in the proper and safe use of
the Autec Radio Remote Control and of the Machine, including without limitation
complete familiarity with and understanding of Autec warnings and instructions, and
all applicable Laws, Regulations and Standards, even local, and that such Users and
other Persons do in fact at all times operate or work with the Autec Radio Remote
Control safely and ONLY in compliance with Autec instructions and warnings and
with all applicable Laws, Regulations and Standards, even local. FAILURE TO DO SO
CAN RESULT IN SERIOUS BODILY INJURY OR DEATH AND/OR PROPERTY DAMAGE.
IT IS THE RESPONSIBILITY OF THE OWNER AND FACILITY OPERATOR, AND THEIR
OFFICERS, MANAGERS AND SUPERVISORS, to be certain that the areas in which
the Machine operated by or through the Autec Radio Remote Control is located and
operates are clearly delineated and marked in accordance with all Autec warnings
and instructions, and all applicable Laws, Regulations and Standards, even local, and
otherwise su󰓑cient to alert and warn ALL PERSONS that the Machine is operated by
or through a Radio Remote Control, and prohibiting any unauthorized access thereto.
FAILURE TO DO SO CAN RESULT IN SERIOUS BODILY INJURY OR DEATH AND/OR
PROPERTY DAMAGE.
FAILURE TO OPERATE THE AUTEC RADIO REMOTE CONTROL SAFELY AND IN
COMPLIANCE WITH AUTEC INSTRUCTIONS AND WARNINGS AND WITH APPLICABLE
LAWS, REGULATIONS AND STANDARDS, EVEN LOCAL, AND/OR PERMITTING USERS
OR OTHER PERSONS NOT PROPERLY TRAINED IN THE SAFE AND PROPER USE
OF THE SYSTEM, OR THE MACHINE ON WHICH IT IS INSTALLED, CAN RESULT IN
SERIOUS BODILY INJURY OR DEATH AND/OR PROPERTY DAMAGE.
AUTEC LIUA8BEN0_eng-01

INDEX
1 Information on the use of instructions ................................................................ 7
1.1 Structure of the Instruction Manual ................................................................ 7
1.2 Caption and terminology ................................................................................ 9
1.3 Symbols ........................................................................................................ 9
1.4 To whom the instructions are addressed ..................................................... 10
1.5 Instruction storage ....................................................................................... 10
1.6 Intellectual property ..................................................................................... 10
2 Brief product presentation ................................................................................. 11
2.1 Series, Radio Remote Control and Unit ....................................................... 11
2.2 Conformity with standards ........................................................................... 11
2.3 Contacts and useful addresses .................................................................... 11
2.4 Warranty ..................................................................................................... 11
2.5 Technical assistance and spare parts .......................................................... 11
3 Description of the Transmitting Unit ................................................................. 12
4 Technical data ..................................................................................................... 13
5 Technical Data Sheet .......................................................................................... 13
6 Plates ................................................................................................................... 14
6.1 Plates on the A8+ Transmitting Unit in a Radio Remote Control .................. 14
6.2 Plates on the A8+ Transmitting Unit in a "Take & Release"
Radio Remote Control ................................................................................. 14
6.3 Plates on the A8+ Transmitting Unit in a "Multi Units" or "Multi Receiver"
Radio Remote Control ................................................................................. 14
7 Light signals ........................................................................................................ 15
8 General operating instructions .......................................................................... 18
8.1 Power keyswitch .......................................................................................... 18
8.2 START pushbutton ...................................................................................... 18
8.3 STOP pushbutton ........................................................................................ 18
8.4 FUNCTION pushbutton ............................................................................... 19
8.5 Battery ......................................................................................................... 19
8.6 ID internal tx memory .................................................................................. 21
8.7 Starting up the Radio Remote Control ......................................................... 22
8.8 Command activation .................................................................................... 24
8.9 Radio link interruption .................................................................................. 24
8.10 Transmitting Unit automatic switch o󰘯 ......................................................... 24
8.11 Switching o󰘯 the Transmitting Unit .............................................................. 25
8.12 "Data Feedback" function ............................................................................ 26
8.13 BACK-UP UNIT ........................................................................................... 27
9 Instructions for the User .................................................................................... 28
9.1 Usage restrictions ........................................................................................ 28
9.2 User behaviour ............................................................................................ 28
9.3 Pouch with belt ............................................................................................ 30
10 Maintenance ........................................................................................................ 32
11 Malfunction signalled by the Transmitting Unit ................................................ 32
12 Decommissioning and disposal ......................................................................... 33
LIUA8BEN0_eng-01 AUTEC

1 Information on the use of instructions
Before reading this part of the Manual, you must read and understand the general
part (Part A) of the Manual provided with the Radio Remote Control.
1.1 Structure of the Instruction Manual
The Manual for the use and maintenance of Autec Air series Radio Remote Controls consists of
di󰘯erent parts, that altogether form the Manual; the Manual must be read carefully, understood
and applied by the Radio Remote Control's Owner, User and by all those Persons that, for any
reasons, may operate with the Radio Remote Control or with the Machine where it is installed.
The following table describes the structure of the Instruction Manual for the use and the
maintenance of the Radio Remote Control.
Part Title Contents
AGeneral part
- General information regarding the series,
- directions for risk assessment of the "Machine+Radio Remote
Control" system,
- warnings for installation of the Radio Remote Control,
- warnings for use and maintenance of the Radio Remote Control,
- instructions for correct transportation and storage of Radio Remote
Control.
BConformity and
frequencies
- Operating frequency bands of the Radio Remote Control,
- conformity and law references of the Radio Remote Control.
CTransmitting Unit
Description and instructions concerning the Transmitting Unit,
including:
- description of operation,
- commands,
- light signals,
- malfunctions,
- additional instructions to the general part.
DReceiving Unit
Description and instructions concerning the Receiving Unit,
including:
- description of operation,
- light signals,
- malfunctions,
- additional instructions to the general part.
EBattery and
Battery Charger
Description, warnings and instructions concerning batteries and
Battery Chargers, including:
- description of operation,
- light signals,
- malfunctions,
- instructions for the User.
AUTEC - Air series
Information on the use of instructions 7
LIUA8BEN0_eng-01

Usage and maintenance instructions are supplemented by the Radio Remote Control's
Technical Data Sheet, that:
-describes the Transmitting Unit's con󰘰guration,
-indicates the relation between commands sent by the Transmitting Unit and those available
on the Receiving Unit.
Usage and maintenance instruction as a whole are to be considered as an integral part both
of the Autec Radio Remote Control and of the Machine, system, device or Machinery system
where the Radio Remote Control is installed.
The Manufacturer of the Machine on which the Autec Radio Remote Control is installed, and
the Owner and User of the Machine, must make sure that the Instruction Manual and all of
its parts are included in the Instruction Manual of the Machine.
The CD attached to each Instruction Manual includes the translations of the Manual.
Act as follows to identify the single Manual parts in the relevant language in the CD:
-identify the correct section depending on the Radio Remote Control serial number,
-choose the desired language,
-select the single parts of the Manual: refer to the code name provided on the cover of
each part.
XXXXXXXXX_language-XX
XXXXXXXXX_language-XX
Instruction Manual for the use and the
maintenance of the Radio Remote Control
Original instructions
Part X: XXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XX SERIES
8
LIUA8BEN0_eng-01
Information on the use of instructions
AUTEC - Air series

1.2 Caption and terminology
Contact Autec if any of the instructions, symbols, warnings or images are not
clear and understandable, or if you have doubts or questions.
In this part of the Manual, the terms listed below have the same meaning explained in the
corresponding paragraph of the general part (Part A):
-Unit
-Radio Remote Control
-Transmitting Unit
-Receiving Unit
-Machine
-Manufacturer
-Installer
-User
-Maintenance Technician
-Manual or Instruction Manual
-Installation Manual
-Person
-Owner
Functions indicated for the Manufacturer, the Installer, the User and the Maintenance
Technician may be performed by a single Person, if he/she has the needed competence
and undertakes the resulting responsibilities. Each Person must be aware of the instructions
contained in the Manual, depending on the activity they carry out.
For example, if a Manufacturer is also the Installer, and/or Maintenance Technician, he must
also know and follow the instructions speci󰘰cally addressed to those Persons. The same
applies, for example, if a User is also the Manufacturer and/or the Installer.
1.3 Symbols
This symbol identi󰘰es the parts of text in the Manual that must be read with
special attention.
This symbol identi󰄈es the parts of text in the Manual containing warnings,
information and/or instructions that are particularly relevant with regards
to safety; failure in understanding them may cause hazards for People and/
or property.
AUTEC - Air series
Information on the use of instructions 9
LIUA8BEN0_eng-01

1.4 To whom the instructions are addressed
Addressees of instructions are listed in the paragraph with the same title in the general part:
please refer to that part.
1.5 Instruction storage
Regulation for the storage of instructions are described in the paragraph with the same title
in the general part: please refer to that part.
1.6 Intellectual property
Restrictions connected to intellectual property are described in the paragraph with the same
title in the general part: please refer to that part.
10
LIUA8BEN0_eng-01
Information on the use of instructions
AUTEC - Air series

2 Brief product presentation
2.1 Series, Radio Remote Control and Unit
The object of this part of the Manual is the A8+ (Model A08 Type LA5AM) Transmitting Unit
of an Air series' Autec Radio Remote Control.
Autec Air series' Radio Remote Controls are designed to be used on Machines and provide
a command interface to their command and control system, to be used from an appropriate
distance and position.
2.2 Conformity with standards
The conformity of Radio Remote Controls with standards and with working requirements and
conditions in the single Countries is provided in the related speci󰘰c part “Conformity and
frequencies” (Part B) of the Manual.
2.3 Contacts and useful addresses
The Radio Remote Controls are produced by Autec srl – Via Pomaroli, 65 – 36030 Caldogno
(VI) – ITALY.
You can 󰘰nd contacts for Autec, its distributors, dealers and authorized service centres on
the website www.autecsafety.com.
2.4 Warranty
General warranty conditions are indicated both in the relevant sheet provided together with
this documentation, and in the speci󰘰c page on the website www.autecsafety.com.
2.5 Technical assistance and spare parts
If you need technical services and/or spare parts, please refer to contacts provided in the
website www.autecsafety.com.
When applying for technical service to Autec, its distributors, dealers and authorized service
centres, the Radio Remote Control's serial number is required; you can 󰘰nd it on the
identi󰘰cation plate on the Transmitting Unit and/or on the Receiving Unit.
AUTEC - Air series
Brief product presentation 11
LIUA8BEN0_eng-01

3 Description of the Transmitting Unit
A
B
C
D E F G
H
J
K
L
AUTEC srl via Pomaroli, 65 Caldogno (VI) ITALY
MADE IN ITALY
TYPE LA5AM
MODEL: A08
FCC ID: OQA-A08LA5AM
IC: 9061A-A08LA5AM
BATTERY RADIO
MODULE
FREQUENCY
AIRTR08LM
433.050-434.790MHz
915-928MHz
......................
..........
.............................................
..........................
LPM00 3.7V
M
ALEDs
BCommand pushbuttons
CFUNCTION pushbutton
DSTART pushbutton
EBattery
FBattery housing
GPower keyswitch
HDIP switches
JConnector for "ID internal tx memory"
KTechnical data plate
LRadio Remote Control identi󰘰cation
plate
MSTOP pushbutton
12
LIUA8BEN0_eng-01
Description of the Transmitting Unit
AUTEC - Air series

4 Technical data
Power supply (battery LPM00) ............................................................................... 3.7V
Antenna .................................................................................................................. internal
Housing material .......................................................................................... PA 6 (20%fg)
Protection degree ....................................................................................... IP65 (NEMA 4)
Dimensions ............................................................ 64.5x179x37.5mm (2.54x7.05x1.48In)
Weight ......................................................................................................... 250g (0.55Lb)
Run time at 20°C (68°F) .............................................................................................. 16h
Maximum altitude (a.s.l.) ......................................................................................... 2000m
Continuous vibration ..................................................................... 0.35mm, 5g (10-150Hz)
Shock ................................................................................................. half sine, 11ms, 30g
Fall ...................................................... 2 falls from a height of 1m onto a concrete surface
Power frequency magnetic 󰘰eld immunity according to CEI EN 61000-4-8 ... up to 300A/m
5 Technical Data Sheet
The Radio Remote Control 's Technical Data Sheet:
-describes the Transmitting Unit's con󰘰guration,
-indicates the relation between commands sent by the Transmitting Unit and those available
on the Receiving Unit.
The Technical Data Sheet must be 󰘰lled in, checked and signed by the Installer, who is
responsible for correct wiring.
A Technical Data Sheet must always be kept together with this Manual: if you need to use
the Technical Data Sheet for administrative purposes (tests, check, etc.), make a copy of it.
The wiring of the Receiving Unit's outputs must always re󰄉ect the wiring
indicated in the Technical Data Sheet.
AUTEC - Air series
Technical data 13
LIUA8BEN0_eng-01

6 Plates
The following instructions refer to the plates on di󰘯erent types of Radio Remote Controls
where the A8+ Transmitting Unit may be used.
6.1 Plates on the A8+ Transmitting Unit in a Radio Remote Control
Plate Position Content
Radio Remote Control
identi󰄈cation plate Battery housing Radio Remote Control serial number
(S/N), bar code and manufacturing year.
Technical data plate Battery housing
MODEL, TYPE and main Transmitting
Unit's technical data, marking and
possible Radio Remote Control marks.
6.2 Plates on the A8+ Transmitting Unit in a "Take & Release" Radio Remote
Control
Plate Position Content
Radio Remote Control
identi󰄈cation plate Battery housing Radio Remote Control serial number
(S/N), bar code and manufacturing year.
Technical data plate Battery housing
MODEL, TYPE and main Transmitting
Unit's technical data, marking and
possible Radio Remote Control marks.
6.3 Plates on the A8+ Transmitting Unit in a "Multi Units" or "Multi Receiver"
Radio Remote Control
Plate Position Content
Radio Remote Control
identi󰄈cation plate Battery housing
Radio Remote Control serial
number (MULTI S/N), bar code and
manufacturing year.
Technical data plate Battery housing
MODEL, TYPE and main Transmitting
Unit's technical data, marking and
possible Radio Remote Control marks.
14
LIUA8BEN0_eng-01
Plates
AUTEC - Air series

7 Light signals
ARed LED
BGreen LED
CLEDs for "Data
Feedback" function
The A8+ Transmitting Unit always has a green LED [B] and a red LED [A] that provide
information regarding the Radio Remote Control.
Symbol Meaning
This symbol identi󰘰es the red LED [A].
This symbol identi󰘰es the green LED [B].
The meaning of signals provided by the LEDs identi󰘰ed with “C” are explained in
the "Data Feedback" function part (see paragraph 8.12). The meaning of LEDs
related to the "Data Feedback" function are decided and established by the
Machine Manufacturer depending on the Machine's functions for which he wants
to receive information.
The meaning of red LED [A] and green LED [B] signals is described in the following tables;
possible actions to carry out are given in chapter 11.
The meaning of the red and green LED signals cannot be modi󰘰ed.
AUTEC - Air series
Light signals 15
LIUA8BEN0_eng-01

Signal Meaning
The green LED [B] is o󰓐. The Transmitting Unit is o󰘯.
The green LED [B] is lit with a
steady light. The Transmitting and Receiving Unit do not communicate.
The green LED [B] repeats the
sequence: two blinks and a pause.
The working range of the remote control has been
exceeded for more than 20 seconds.
The green LED [B] repeats the
sequence: three blinks and a
pause.
The Receiving Unit does not communicate with the
transmitting Unit. If the Transmitting Unit communicates
with the Receiving Unit, it is possible to send commands.
The green LED [B] blinks fast.
The Transmitting and Receiving Unit communicate. It
is only possible to send commands after pressing the
START pushbutton.
The green LED [B] blinks slowly
(one blink per second). It is possible to send commands.
Signal Meaning
The red LED [A] is o󰓐. The Transmitting Unit works correctly.
The red LED [A] is steady on
during start up. The STOP pushbutton is pressed or damaged.
The red LED [A] blinks twice per
second during start up. At least one of the pushbuttons is pressed or damaged.
The red LED [A] blinks three times
per second during start up. The battery is 󰘱at.
The red LED [A] is lit for 2s with a
steady light. The Transmitting Unit does not work correctly.
The red LED [A] blinks slowly (one
blink per second). The battery has a run time of approximately 3h.
The red LED [A] blinks fast. The battery has a 10min run time.
16
LIUA8BEN0_eng-01
Light signals
AUTEC - Air series

Signal Meaning
The green [B] and red [A] LEDs are
steady on during start up.
A wrong "ID internal tx memory" has been inserted in the
Transmitting Unit, or this is a "BACK-UP UNIT".
The green [B] and red [A] LEDs
blink 3 times per second during
start up.
"ID internal tx memory" is damaged.
The green LED [B] is lit with a
steady light and the red LED [A]
blinks two times per second during
start up.
The START pushbutton is activated.
The green [B] and red [A] LEDs
blink alternating. 30 s left before the Unit automatically switches o󰘯.
The green LED [B] repeats the
sequence: 3 blinks and a pause,
and the red LED [A] is steady on
during start up.
The UNPAIR procedure has been carried out.
AUTEC - Air series
Light signals 17
LIUA8BEN0_eng-01

8 General operating instructions
8.1 Power keyswitch
The Transmitting Unit always has a power keyswitch that allows to power the Unit.
The Radio Remote Control cannot work if the power keyswitch is not inserted in the Transmitting
Unit.
Power keyswitch
8.2 START pushbutton
The START pushbutton is used to:
-start the Radio Remote Control (see paragraph 8.7),
-activate the horn when the Radio Remote Control is started.
8.3 STOP pushbutton
When the STOP pushbutton is activated, the Machine stops and the Transmitting Unit switches
o󰘯. To start the Radio Remote Control again and enable it to control the Machine after the
STOP pushbutton has been pressed, you need to:
-make sure that the working and usage conditions are safe,
-pull or turn the STOP pushbutton in the arrow direction (show on the button) to unlock it,
-start the Radio Remote Control following the procedure described in paragraph 8.7.
The STOP pushbutton should be pressed when it is necessary to stop the
Machine immediately whenever a dangerous condition occurs.
The Machine Manufacturer and/or the Installer must provide the User with the
instructions and warnings concerning possible risks that may originate from
the Machine stop (by way of example: movement inertia, swinging load…).
18
LIUA8BEN0_eng-01
General operating instructions
AUTEC - Air series

8.4 FUNCTION pushbutton
The function of the FUNCTION pushbutton is decided by the Installer of the Radio Remote
Control. The Machine Manufacturer and/or the Installer must provide the user with instructions
about the relation between the FUNCTION pushbutton and the corresponding movement on
the Machine. The User must be properly trained about this.
8.5 Battery
The Air series' Transmitting Units can only be powered by Autec rechargeable
batteries.
For any warnings and instructions regarding the battery, see "Part E" in
the Instruction Manual.
8.5.1 Battery insertion
Push the battery towards the contacts on the Transmitting Unit (1) and insert it inside the
housing (2).
1
2
The battery slides in with no e󰘯ort and ensures the correct connection of the positive
(+) and negative (-) poles only if it is inserted as shown in the above pictures.
AUTEC - Air series
General operating instructions 19
LIUA8BEN0_eng-01

8.5.2 Battery removal
Push the battery towards the contacts on the Transmitting Unit (3) and remove it from the
housing (4).
3
4
When the Transmitting Unit is not in use, remove the battery if possible.
8.5.3 Indication of the battery charge level
Perform the following actions to check the Transmitting Unit's battery
charge level:
1. Switch off the Transmitting Unit and make sure that the STOP
pushbutton is unlocked.
2. Hold down pushbuttons S1 and START until the 3 LEDs on the left
hand side illuminate showing the Unit's charge level (3 illuminated
LEDs=maximum charge level). The charge level indication disappears
after some seconds.
Commands associated to the keys that are activated during the procedure to
check the battery charge level are not sent to the Machine.
20
LIUA8BEN0_eng-01
General operating instructions
AUTEC - Air series