Auto Page KE-120 User manual

KE-120
CUSTOMER SYSTEM OPERATIONS
1) ACTIVE LOCKING & UNLOCKING
Active or Manual locking is activating the System by the Remote Control Transmitters.
(Interfacing the vehicles horn and starter interrupt circuit requires additional installation.)
Active locking is as follows…
a) Press button on the Remote Control Transmitter.
b) The horn will honk once, the parking lights will flash once & the doors will lock.
c) A steady flashing of the System LED will confirm locked status.
Unlocking is as follows…
a) Press button on the Remote Control Transmitter.
b) The horn will honk twice, the parking Lts. will flash twice & the doors will unlock.
c) The System LED will turn off indicating unlocked status.
2) PANIC FUNCTION
In the event of an emergency, the Remote Control Transmitter can be used to activate the
System Panic Mode. (Interfacing the vehicles horn to the System requires additional
installation.) Panic Mode operation is as follows…
a) Push and hold the button for more than 3 seconds.
b) The horn will begin honking and the vehicles parking lights will begin flashing.
3) CAR LOCATOR FUNCTION
To help locate your vehicle when out of sight our parked in a crowded parking lot.
(Interfacing the vehicles horn to the System requires additional installation.)
You can activate the Car Locator by:
a) Push button while system is locked
b) The horn will sound chirping 6 times & the parking lights will flash 12 times.
4) VALET / OVERRIDE SWITCH
(The Valet / Override Switch has dual functions:)
Emergency unlock(To dis-engage the optional starter interrupt circuit) –In the event the
Remote Control Transmitter malfunctions or is lost the System can still be disarmed.
Emergency unlock is activated as follows…
a) Turn the vehicles ignition to the “ON” position and press the Valet / Override
Switch once.
b) The System is now de-activated.
Valet Mode –In the event the vehicle needs to be serviced or valet parked, the System
can be programmed into a “Valet Mode” that will only allow the Remote Control
Transmitters to activate the door lock / unlock circuit. Programming Valet Mode is as
follows…
a) Turn the vehicles ignition to the “ON” position and push the Valet / Override
Switch for 2 seconds or until the System LED turns on solid. The System is now
in Valet mode.
b) To return the System to normal operation, turn the vehicles ignition “ON”
position and push the Valet / Override switch for 2 seconds or until the System
LED turns off. The System has resumed normal operation.
5) IGNITION CONTROLLED DOOR LOCKS
When the vehicles ignition is turned “ON” the door will automatically lock and when the
vehicles ignition is turned “OFF” the doors will automatically unlock. *
6) DOME LIGHT ILLUMINATION
When the System is locked, the vehicles dome light will illuminate for 10 seconds. When
the System is unlocked, the vehicles dome light will illuminate for 30 seconds. *
7) REMOTE CONTROL TRANSMITTER OPERATION
Transmitter Button System Function
Locks the door / flashes the parking lights once /
Activates the horn once* / starter interrupt circuit engaged*
3 Seconds ( Panic ) Activates the horn* / flashes the parking lights
(Push and hold button for 3 sec.)
–Car Locator Activates the horn* 6 chirps & Flashes parking 12 times
(Push the button when system is activated)
Unlocks the doors / flashes the parking lights twice
Activates the horn twice* / De-activates Panic
-Unlocks the Drivers door on the first push, then unlocks the
Rest of the doors on the 2P
ndPpush/ flashes parking lights twice.
Activates channel 2 output (Push and hold button
for 3 seconds to activate) Trunk Pop
Panic
(Push and hold button for 3 sec.)
+ Silent Arm/ Disarm Activates silent Locking mode (Push both buttons and
at the same time to activate)*
Optional silent lock and unlock (Programming Required)
* Additional Installation may be required
8) LED & HORN INDICATORS
LED HORN*
Operation Function Operation Function
Off Unlocked 1 Chirp Locked
Slow Flash Locked 2 Chirps Unlocked
Fast Flash Passive Locking Mode Engaged
& programming mode Continuous Chirp
Panic Mode Engaged
On (Solid) Valet Mode
(30 seconds)
* Additional Installation may be required

9) PARKING LIGHT INDICATORS
PARKING LIGHTS
Operation Function
1 Flash + 10 sec on Locked/ The parking lights will remain “on”for 10 sec.
2 Flashes + 30 sec on Unlocked / The parking lights will remain “on” for 30 seconds
Continuous Flash Panic Mode Engaged (30 Sec.)
10) STARTER INTERRUPT CIRCUIT (OPTIONAL)
The vehicles starter circuit may be interrupted for additional protection when the System is
locked. Use of the RK-1 Starter Interrupt Relay kit is recommended.
11) TRANSMITTER PROGRAMMING
In the event, you should need to add or replace a Remote Control Transmitter, it is
important that you follow the instructions below.
Note: Each step must be performed within 10 seconds of the previous step otherwise the System
will exit the programming mode.
PROGRAMMING THE REMOTE TRANSMITTER
Enter:
1. Turn the Ignition ‘switch ‘OFF/ON’ 3 TIMES and stay in ON
position. Within 15 seconds.
2. Push the Valet switch 2 times. (Holding in on the 2nd push) until you hear a long chirp. The
transmitter is ready to program.
Program:
1. Press any button on the transmitter until the horn responds with a confirming chirp and parking
light flash once the first transmitter is now programmed.
2. Press button on the second transmitter until the horn responds with a confirming chirp, the
second transmitter is now programmed.
3. Apply the same procedure to program 3rd and 4th.
Exit: Turn Ignition to ‘OFF’ position, or leave it for 15 seconds. A 3 long chirps to confirm exit.
You must register your product online at http://www.autopageusa.com to
receive any warranty service.
Please go to the customer service tab and select product registration.
Warning: Some batteries may contain Perchlorate
For Warranty Information, Please visit www.autopageusa.com
KE-120
PROFESSIONAL KEYLESS ENTRY SYSTEM
OPERATIONS MANUAL
Please register your product at
www.autopageusa.com
THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY