AV Access HDW200 User manual

1. Application
Note:
(1) Ensure the Wireless Channel -- DIP switches of transmitter and
receiver are set to the same positions.
DIP Position Channel Number
1 2 3
Up Up Up 1
Up Up Down 2
Up Down Up 3
Up Down Down 4
Down Up Up 5
Others Reserved
(2) Up to five sets of HDW200 transmitter and receiver can be
deployed in the same zone.
2. Specications
Technical
Input A/V Port Transmitter: 1 x HDMI
Receiver: 1 x WLAN
Input Resolutions Up to 1080P@60Hz
Technical
Output A/V Port Transmitter: 1 x HDMI, 1 x WLAN
Receiver: 1 x HDMI
Output Resolutions Up to 1080P@60Hz
Compliance HDMI 1.3, HDCP 1.4
Transmission Distance 200m/656ft (line of sight)
General
Operating Temperature +32°F ~ +113°F (0°C ~ +45°C)
10% ~ 90%, non-condensing
Storage Temperature -4°F ~ 140°F (-20°C ~ +70°C)
10% ~ 90%, non-condensing
Power Supply DC 5V 1A
Power Consumption TX: 3.5W (Max) RX: 1.6W (Max)
ESD Protection Human body model:
• ±8kV (air-gap discharge)
• ±4kV (contact discharge)
Product Dimension
(W x H x D)
140mm x 21mm x 80mm/5.5'' x 0.83'' x 3.15"
each for TX and RX (Antennas not included)
Net Weight TX: 0.31kg; RX: 0.30kg
Gross Weight 1.10kg
3. Package Contents
1 x Transmitter; 1 x Receiver; Others: 2 x Antennas; 2 x Power
Adapters (DC 5V 1A); 2 x Exchangeable US Plugs; 1 x IR Emitter;
1 x Broadband IR Receiver (30-50KHz); 4 x Mounting Ears (with
Screws); 1 x Quick Start Guide
4. FAQs
(1) What should I do when Link LED is on, but there's no video output
on the remote display?
• Check and ensure the DIP switches on both transmitter and
receiver(s) are set to the same positions.
• Check and ensure the HDMI source is powered on, and the
transmitter's HDMI In LED is on.
• Connect the HDMI source device directly to the display to see if
there's signal output.
www.avaccess.com
www.avaccess.com [email protected] [email protected]
TV
DVD Player
IR Emitter IR Receiver
DVD Player Remote
TV
Transmitter Receiver

(2) How to deal with poor video quality?
• Check if the HDMI cables are connected properly. Use different
HDMI cables if necessary.
• Change the angles of the antennas on transmitter and receiver
to make the antennas parallel to each other (refer to Fig a).
Operation in Fig b&c is not recommended.
Transmitter Receiver
Fig (a)
Transmitter Receiver
Fig (b)
Transmitter Receiver
Fig (c)
• Decrease the distance between the transmitter and receiver to
ensure it is within the available transmission range.
• Remove other wireless signals and any obstacles that are
blocking the signal line-of-sight.
(3) Why the IR remote controller seems not sensitive enough?
Avoid to press and hold the IR remote controller's buttons.Try to
short press them intermittently instead.
5. Panel Layout
Transmitter
www.avaccess.com [email protected] V1.0.0
6
7
11
10
98
5554321
Features and Ports
1. Power input port | 2. Reset Key and Led | 3. HDMI In port |
4. HDMI Out port | 5. IR Out port | 6. Update port | 7. Antenna |
8. Power Led | 9. Link Led | 10. HDMI In Led | 11. Wireless Channel
Receiver
Features and Ports
a. Power input port | b. Reset Key and Led | c. HDMI Out port |
d. IR In port | e. Update port | f. Antenna | g. Power Led | h. Link Led |
i. Wireless Channel
f
ih
g
55edcba