AV-GAD EasyLoader AV-701 User manual

EasyLoader
End User Manual
Downloaded from: http://www.guardianalarms.net

2
Table of Contents
Table of Contents...................................................................................................................... 1
System Configuration............................................................................................................... 3
Introduction.............................................................................................................................. 4
SAFETY AND MAINTENANCE INSTRUCTIONS.................................................................... 4
GLOSSARY......................................................................................................................... 4
Basic Operations....................................................................................................................... 8
ARMING YOUR SYSTEM.................................................................................................... 8
DISARMING ....................................................................................................................... 8
AMBUSH DISARMING ........................................................................................................ 8
ZONE BYPASSING.............................................................................................................. 9
HOW TO BYPASS ZONES ................................................................................................... 9
ARMING CHOICES ............................................................................................................. 9
AV-701T Keypad..................................................................................................................... 11
LED INDICATORS............................................................................................................ 12
KEYPAD DISPLAY ............................................................................................................ 12
SETTING NEW CODE FOR THE AV-701 ........................................................................... 13
DELETE A USER CODE .................................................................................................... 14
SETTING THE FOLLOW-ME TELEPHONE NUMBER .......................................................... 14
SOUNDER ........................................................................................................................ 14
AV-707 Keypad....................................................................................................................... 15
INTRODUCTION ............................................................................................................... 15
LCD DISPLAY.................................................................................................................. 16
KEY ENTRIES .................................................................................................................. 16
SETTING NEW CODE FOR THE AV-707 ........................................................................... 16
SETTING FOLLOW-ME TELEPHONE AT AV-707 ............................................................. 17
Displaying System Information.............................................................................................. 18
ALARM MEMORY DISPLAY............................................................................................. 18
EVENTS DISPLAY ............................................................................................................ 18
TROUBLE CONDITIONS.................................................................................................... 18
Setting System Features .........................................................................................................19
CHANGING CODES .......................................................................................................... 19
DELAYS DELETE ............................................................................................................. 19
Testing Your System............................................................................................................... 20
SIREN AND BATTERY TEST ............................................................................................. 20
DETECTION DEVICES TEST ............................................................................................. 20
TESTING YOUR CENTRAL STATION (CS) ........................................................................ 20
Troubleshooting...................................................................................................................... 21
Av-Gad Limited Warranty...................................................................................................... 23
@ All Rights Reserved to AV-GAD SYSTEMS LTD, Tel Aviv, Israel. POB 49 080 Tel-Aviv 61 104, Israel. / W7/ END_2000_2. June 02

3
System Configuration
Zone Index
Zone Description Type Zone Description Type
1 9
2 10
3 11
4 12
5 13
6 14
7 15
8 16
Installation Data
Installer CS Information Programmed Telephones
Phone: Phone:
Mobile: Account No.:
Installation date: Contact Person:
Zone at Home Mode Siren Times Silent Zones
Notes
--------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------

4
EASYLOADERTM SERIES
ALARM CONTROL PANELS
End User Operating Manual
(for version 2.17)
Congratulations for purchasing this state-of-art computerized security panel. You
have made a wise investment in the future safety of your home or business premises
with this high-technology security system, however still EASY as 1,2,3.
All of Av-Gad products conform to year 2000.
Introduction
Review this manual carefully before operating your security system.
Your installer should instruct users how to operate the system, and about its various
features. Complete the System Configuration page and store this manual in a safe
place for future references.
Safety and Maintenance Instructions
Your security system cannot prevent burglaries, emergency case or damage to your
property. It is only intended to alert emergencies.
To keep your system efficient as intended it’s recommended to test the system daily;
upon arming and weekly testing the siren and detection devices. Read the ‘Testing
your System’ section. If your system does not function properly, contact your installer.
Keep the keypad dry; clean the keypad with dry cloth. Never disconnect the main AC
to your system.
Glossary
Your security system has been designed to offer the latest security features with
simple and easy operation. Described here are some terms that are used throughout
this manual to explain the common terms in this manual.
Group Bypass - (HOME mode)
‘Group Bypass’ allows bypass of zones determined by the installer to be bypassed at
once by entering a short keys combination prior to Arming.
24-hour Zone
A zone programmed for 24-hour protection. Zone is active in both Armed and Disarmed
modes. When a 24-hours zone is troubled, alarm will sound in both Armed and
Disarmed mode.
Battery
Standby battery located in the control box provides emergency backup power in event of
power loss.

5
Bypass (Shunt) a zone
Allows manual removal of one or more protected zones from the system.
Day and Tamper Zone
A zone programmed as a Day or Tamper Zone enables alarm from keypad's buzzer
during daytime, when system is usually disarmed. The Day or Tamper zone will trigger
the keypad buzzer and the zone number will flash on keypad display. To reset Day Zone
alarm, hold-down key 9 (reset key).
During Armed mode, this zone will act as burglary zone and will emit an alarm when
troubled.
Dialer and Communicator
Alarm reports directly to predetermined stations via telephone lines. The dialer reports
an alarm to your telephone, a siren or a recorded message. To report a message, a SVM-
40 unit is required.
Digital Display
Keypad display. Provides alphanumerical readout of zone status and messages.
Entry Delay
The Entry Delay is the period allowed for someone to enter the premises and disarm the
system.
Entry-Exit Zone
The entry-exit door or zones are designated by your installer to be used for entering and
leaving the premises when the system is armed.
Exit Delay
The Exit Delay is the period allowed for users to leave the premises after arming the
system.
Fire Zone
A zone programmed for connection of fire or smoke detector. Alarm heard in both
Armed and Disarmed modes, and Fire LED is activated.
The siren sound is different from the 24H zone or burglary alarm (it depends on the
siren type used). To reset Fire alarm, hold-down ‘9’ key and your code.
‘Follow-Me’ Programmable Telephone Number
Dialer feature. The desired Follow Me Telephone number is programmed by the user
prior to arming – as necessary (to follow the user destination).

6
Follower Zone (also called conditioned Zone)
Follower Zone reacts instantly upon detection without previous triggering of Delayed
zone. Exit delay applies to Follower zones.
Hold-down Functions
Holding down keys for about 2 seconds provides additional easy-to-access functions.
Instant Arming
Instant Arming of system. Short press on key 5 instantly arms system.
Instant Zone
Zone feature. System reacts instantly upon detection at a zone, which has been
programmed as ‘Instant.’
Key-switch (optional)
Located on control panel door or remote panel. Used for arming/disarming the system.
Keypad
Your system contains one or more keypads. The keypad is used to operate the system,
and to view operating information about the system. Information about the system is
displayed. Commands are entered on the keypad by pressing one key at a time.
LCD
Shortening for ‘Liquid Crystal Display’. This type displays full texts, zone locations,
messages, etc.
LED
Shortening for ‘Light Emitting Diode’. LED is a modern bulb. LED visually displays the
system status and confirms the functions.
Master Code
The Master Code is a 4 to 6 digit code used to arm and disarm the system, to program
your codes and to bypass zones (in certain models). Normally, only one person should
know the Master Code. Your default master code is 1,2,3,4.
Panic Button
Two keys (* and #) on the digital keypad, for alerting the central station in case of
emergency.
Programmable Features
Computerized control panel allows system tailoring to suit individual requirements.
Smoke Detectors
Triggers alarm upon detection of smoke. Smoke detector requires reset after alarm.

7
Sounder
The sounder (in Keypad) simplifies alarm recognition by producing different amounts
and patterns of sounds to identify various events. The sounder also functions as key-
press confirmation.
User Codes
One master and seven codes are available to allow users to arm and disarm the system
and to bypass zones. Keep the code confidential to ensure maximum system security.
Zone (also called area)
An area protected by a security device. For example, a room protected by a motion
detector as Zone number 1, while a door protected by a magnetic contact as Zone
number 3. Your installer will inform you which zones have been set up on your
system. The AV-701 contains a zone index list. The AV-707 displays the zone
description.

8
Basic Operations
Arming Your System
Before arming your system, close all protected doors and windows, and stop
movement in areas protected by motion detectors. When all protective zones are
closed, the Green Status LED stops blinking.
To arm the system, enter your code. At each digit entry, the keypad sounder will beep.
When the code has been entered, the Armed LED will light. If an incorrect user code
is entered, the keypad will sound a single long tone. To correct the mistake, press ‘9’
and enter the code again.
When the Armed light is on, leave the premises through the designated entry-exit door
before the exit delay expires. At the end of the exit delay, all lights on the keypad will
be shut off, except for the Red Armed light - your system is now armed.
The factory setting for the exit delay is 30 seconds; your installer may change this
time to suit your needs. Refer to the Arming Options section of this manual for
information on other arming functions.
Disarming
Enter the premises through the designated entry-exit door. The keypad will sound a
constant tone to indicate that the system must be disarmed.
Enter your code at keypad, if an error made while entering the code, press ‘9’ and
enter the code again. After six wrong entries, the keypad locks itself for 30 seconds,
keys do not respond during this period.
When a correct code is entered, the Armed light shuts OFF, and the sounder is silent -
your system is now disarmed.
Enter your code before the entry delay expires (to prevent alarm). The factory setting
for the entry delay is 12 seconds; your installer may change the time to suit your
needs.
If an alarm occurs while the system is armed, the Armed LED blinks. Refer to
‘Display Alarm Memory’ for instructions on displaying the zones in alarm.
Ambush Disarming
If you are forced by an intruder to disarm your system, the Ambush alarm can be
activated. Disarming the system with the Ambush code will cause the system to
disarm and simultaneously send a silent ambush alarm signal to central Station. This
is an optional feature. For details ask your installer.
IMPORTANT: If you return to the premises and find that an alarm is in
progress or that there are alarms in memory, do not enter the premises, as an
intruder may be present. Contact the local authorities from your mobile or
public phone.

9
Zone Bypassing
A ‘Bypassed’ zone will not cause an alarm. Zones may be bypassed to allow access to
part of the protected area while other zones are armed. For example, you could bypass
the zone protecting your living room. This would allow you to remain in the room,
while the other zones on your system are armed.
With the system disarmed, hold-down ‘2’ key to display bypassed zones. The zone
number displayed represents bypassed zones. Ensure that any zone displayed as
bypassed is intentionally bypassed. Zone bypasses are automatically cancelled when
the panel is disarmed.
How to Bypass Zones
To bypass a zone press ‘0’ key and the zone number (1 to 8, or 1 to 16 in AV-2016),
the Shunt (Bypass) Yellow light is on in confirmation, enter your arming code, Armed
Red LED goes on.
To remove a bypassed zone, arm then disarm the system, re-enter the bypassed zones.
When you arm your system, the zones you have indicated will now be bypassed.
When arming the system with bypassed zones, it is always recommended to review
the list of bypassed zones before entering your code to arm the system. After
bypassing the desired zones, enter your code to arm the system.
Arming Choices
Home Mode
Arming with Home mode, automatically bypasses the zones programmed as Group
Bypass. This feature allows you to arm the system and remain on the premises.
For new systems, version 2.17 and later: To bypass 1st group press “0” and hold-down
“1”, to bypass 2nd group press ”0” and hold-down “2”, to bypass both groups press
“0” and hold-down “0”.
At Home mode, another member would still be able to enter the premises through the
entry-exit door without causing an alarm (requires special programming). When the
entry-exit door is opened, to disarm the system, enter your user code.
Away Arming
Close all protected doors and windows, you can move in front of the delayed detector,
enter your code, and check if the Armed LED is on. In case of arming with an open
zone, a ≡(three lines) sign will be displayed, indicating that the system is disarmed
warning about a open (troubled) zone.

10
Instant Arming
The Instant Arming feature allows you to press ‘5’ key to arm the system.
This command is designed to allow user to arm the system without needing a full user
code.
Note: The instant arming is not recommended. This will allow the easy arming
by someone who is not a regular user.
Auto Arming
Auto Arming provides setting of the desired system arming time when the regular
user is away. This feature is useful for shop and sites requiring long exit delay.
Enter to user programming mode; hold-down ‘8’ key then enter your master code,
three LEDs are blinking.
Hold down '8' ('A' is displayed); type hour and minutes in 24 hours format.
To display, hold down '8' and wait. To disable Automatic Arming program 0000.
After Automatic Arming is programmed, the system time can be set only via User
Programming Mode: Enter User Programming Mode (hold-down ‘8’ and 1234), hold
down '1' ('t' is displayed) and type hour and minutes. Hold down '1' and wait for the
time to be displayed. Holding down '0'+'1' keys to program the time is possible only if
the Automatic Arming is disabled (otherwise an 'Error’ warning is displayed).
Automatic Arming will not operate if the system time has not been set (blinking 'h').
Automatic Arming will not operate if the control panel is already armed.
Automatic Arming will operate even if the control panel is currently in ALARM.
When the Automatic Arming programmed time arrives, the system starts at a
30-second countdown. An 'A' is intermittently displayed and beeps are sounded at the
keypad.
During the countdown period, the Automatic Arming can be aborted by entering a
valid user code (not code No. 7, if used to ‘open’ a door).
Remote Arming
The Remote Arming allows you to use a remote key switch, or wireless tiny
transmitter to arm the system. This command is designed to arm the system without a
code, or for convenient arming from your car.